Top Water Cooled Machine Reviews

Outboard Motor, 2 Stroke 12 hp 246cc Heavy Duty Boat Engine Fishing Boat Motor w/CDI System Water Cooling System

  • Short axle: axle length 381 mm (15 inches) suitable for boats below 44 cm（17.32inches） (inclusive) transom height.
  • two-stroke water-cooled outboard engine must put the machine in the water to start the machine to start (do not start the machine on shore).
  • 2-stroke water-cooled outboard engine uses the specified two-stroke engine oil in strict accordance with the instructions Mix it with No. 87 gasoline and use it in the correct proportion. Do not use four-stroke engine oil, automobile engine oil, Gear Oil.
  • Attention: It is strictly forbidden to start the machine on the shore. The two-stroke outboard engine should use a mixture of two-stroke engine oil and gasoline. The new machine is running in within 10 hours. The fuel ratio is 30L gasoline: 1L engine oil, and the ratio is oil after 10 hours. 50L: Oil 1L must ensure that gasoline and oil are fully mixed, otherwise it will damage the machine.
  • The ignition system of this outboard motor has a CDI ignition system. So you can start the motor quickly and safely, which saves your time and is very convenient to use. This outboard adop....
Check Stock

Outboard Motor, 6hp Heavy Duty Boat Engine Fishing Boat Motor w/CDI System Water Cooling System (2 Stroke 6 hp)

  • Short axle: axle length 381 mm (15 inches) suitable for boats below 44 cm（17.32inches） (inclusive) transom height.
  • Hangkai two-stroke water-cooled outboard engine must put the machine in the water to start the machine to start (do not start the machine on shore).
  • Hangkai two-stroke water-cooled outboard engine uses the specified two-stroke engine oil in strict accordance with the instructions Mix it with No. 87 gasoline and use it in the correct proportion. Do not use four-stroke engine oil, automobile engine oil, Gear Oil.
  • Attention: It is strictly forbidden to start the machine on the shore. The two-stroke outboard engine should use a mixture of two-stroke engine oil and gasoline. The new machine is running in within 10 hours. The fuel ratio is 30L gasoline: 1L engine oil, and the ratio is oil after 10 hours. 50L: Oil 1L must ensure that gasoline and oil are fully mixed, otherwise it will damage the machine.
  • The ignition system of this outboard motor has a CDI ignition system. So you can start the motor quickly and safely, which saves your time and is very convenient to use. This outboard adopts an international standard air intake system and compression ratio, which can effectively improve combustion efficiency and thus reduce fuel consumption. It....
Check Stock

22" Commercial Ice Maker Machine 550LBS/24H with 350LBS Large Storage Bin, 990W SECOP Compressor, Air Cooled, Automatic Cleaning, Perfect for Restaurants, Bars, Cafes and Other Businesses (Full Ice)

  • ...ce every day? This commercial ice maker can be a good solution to your worries. Up to 550 lbs of ice per day, it can supply all the ice you need for your restaurant, cafe, bar, catering company, or hotel. Serving above 370 meals per day according to 1.5 lbs ice per meal sold in restaurant. In just 8~15 minutes, the machine can produce 182 ice cubes for immediate use, which is perfect for busy establishments..
  • ♪【SECOP Compressor & Air Cooled】As the heart of the ice machine, our machine uses the world's top brand SECOP Compressor.These compressors are known for their high efficiency, durability, low noise, reliability and variable speed operation.Ice machine is air-cooled, compared with water-cooled, has the advantages of low noise, low energy consumption, low water consumption, easy maintenance, etc.You get what you pay for..
  • ♪【High-Quality Materials Create High Performance】Built with heavy-duty, high-quality brushed stainless steel, which is rust-proof and durable while being aesthetically pleasing. Ice storage bin is composed of food grade PP injection liner and six-sided cyclopentane foam layer, not only can easily withstand impact from ice, b....
Check Stock

PENNZOIL Marine TC-W3 2 Cycle Engine Motor Oil 1 qt.

  • For outboard, water cooled & air cooled 2-cycle engines.
  • Including those calling for 100:1 fuel to oil ratio, & all air cooled 2-cycle engines requiring an NMMA TC-W, TC-W11 or TC-W3.
  • Exceeds requirement of water cooled outboards and air cooled engines at heavy loads and high speeds for long periods.
Check Stock

Tormek T-4 Chef’s Kit (Tormek T-4 Original Sharpener + KJ-45 Centering Knife Jig + KJ-140 Wide Centering Knife Jig + SVM-00 Small Knife Holder Jig + SVX-150 Scissor Jig + MH-380) (US Version)

  • This bundle combines the Tormek T-4 water-cooled sharpening system with the jigs trusted by chefs around the world..
  • This Tormek T-4 Chef’s Kit includes all the jigs to keep your kitchen knives and tools sharp. Use the KJ-45 for your knives, the KJ-140 for the longer knives, the SVX-150 for your scissors, and the SVM-00 for small knives. When you are all finished, cover your machine with the MH-380 machine cover to keep it nice and tidy..
  • The Tormek T-4 Original is Tormek’s 8 inch sharpener. It is a low RPM, water-cooled sharpening system that is built for precision sharpening and long tool life. It will keep your tools and accessories razor sharp and always ready to work. Includes both a grinding and honing wheel.
  • Includes: Tormek T-4 Original, PA-70 Honing Compound, SP-650 Stone Grader, WM-200 Angle Master, KJ-45 Centering Knife Jig, KJ-140 Wide Centering Knife Jig, SVM-00 Small Knife Holder Jig, SVX-150 Scissor Jig, and MH-380 Machine Cover.
  • Note: This low RPM machine operates at 115 volts and is designed to work exclusively in North America. If you plan on using this product in a country that operates at 220-240V, you will cause damage to the motor and machine..
Check Stock

Tormek T-8 Chef’s Kit (Tormek T-8 Original Sharpener + KJ-45 Centering Knife Jig + KJ-140 Wide Centering Knife Jig + SVM-00 Small Knife Holder Jig + SVX-150 Scissor Jig + MH-380) (US Version)

  • ... This Tormek T-8 Chef's Kit includes all the jigs to keep your kitchen knives and tools sharp. Use the KJ-45 for your knives, the KJ-140 for the longer knives, and the SVM-00 for small knives. Also included is the SVX-150 for your scissors. When you are all finished, cover your machine with the MH-380 machine cover to keep it nice and tidy..
  • The Tormek T-8 is Tormek’s most powerful sharpener. It is a low RPM, water cooled sharpening system that is built for precision sharpening and long tool life. It will keep your tools and accessories razor sharp and always ready to work. Includes both a grinding and honing wheel.
  • Includes: Tormek T-8 Original, SE-77 Square Edge Jig, PA-70 Honing Compound, SP-650 Stone Grader, WM-200 Angle Master, TT-50 Truing Tool, KJ-45 Centering Knife Jig, KJ-140 Wide Centering Knife Jig, SVM-00 Small Knife Holder Jig, SVX-150 Scissor Jig, and MH-380 Machine Cover.
  • Note: This low RPM machine operates at 115 volts and is designed to work exclusively in North America. If you plan on using this product in a country that operates at 220-240V, you will cause damage to....
Check Stock

WeldingCity 5-Lb ER308L Stainless Steel 308 TIG Welding Rod 3/32\x36\ | Pack of 5-Lb

  • Packing including: The 53pcs tig welding torch stubby gas lens kit accessories including---4pcs TIG Stubby Gas Lens + 4pcs TIG Gas Lens Collets Body + 12pcs TIG Collets+6pcs #10 Pyrex Glass Cup + 10pcs TIG Alumina Nozzle+3pcs TIG back cup+ 2pcs Gasket Cup+12pcs Temperature Resistant O-rings.
  • Fit for: 17 & 26 series air cooled torches + 18 series water cooled torches, Lincoln torch model #---PTA-17/PTA-18/PTA-26 , Miller Diamondback torch model#--DB17/DB18/DB26 AND the Weld craft WP-17/ WP-18 /WP-26.
  • Electric conductivity similar with: 2% thoriated tungsten electrode.
  • Applicable machine: Mitech, Longetivity,Rilon, Krypton, Riland, Jasic, Chiry, UNT, Berlan etc.
Check Stock

Professor Mysterious Ground Hugger Indoor Fog Machine Fluid, Quart

  • To generate amazing low-lying fog effects, a fog cooler or cooled fog machine is required.
  • Generates a medium density, low-lying fog that dissipates before it gets too high.
  • Made from pure RO/DI water and pharmaceutical-grade FDA GRAS materials.
  • Non-toxic, non-flammable, non-staining, and unscented.
  • 1 quart water based fog liquid, compatible with all water-based fog machines 400w and higher.
Check Stock

Tormek T-4 Hand Tool Kit (Tormek T-4 Original + Tormek HTK-806 Hand Tool Kit) - sharpener that includes all the necessary jigs for knives, axes, scissors, and carving tools (US Version)

  • A complete sharpening system for hand tools – this bundle combines the Tormek T-4 water-cooled sharpening system with the HTK-806 hand tool sharpening jig and accessory kit.
  • The HTK-806 hand tool kit includes 6 jigs for sharpening hand tools like knives, scissors, axes, carving tools, and comes with its own storage case.
  • The Tormek T-4 Original is Tormek’s 8 inch sharpener. It is a low RPM, water-cooled sharpening system that is built for precision sharpening and long tool life. It will keep your tools and accessories razor sharp and always ready to work. Includes both a grinding and honing wheel.
  • Includes: WM-200 Angle Master, PA-70 honing compound, SP-650 stone grader, SVM-45 knife jig, SVM-00 small knife jig, SVM-140 long knife jig, SVA-170 axe jig, SVX-150 scissor jig, SVS-38 short tool jig, TC-800 storage case. It’s a sharpening shop in a box!.
  • Note: This low RPM machine operates at 115 volts and is designed to work exclusively in North America. If you plan on using this product in a country that operates at 220-240V, you will cause damage to the motor and machine..
Check Stock

Jet JWS-10 Variable-Speed Wet Sharpening System (727100)

  • CONVENIENT STORAGE: Built-in drawer for jig storage..
  • REDUCED SPLASH: Deep well trough reduces splash while keeping the stone cool..
  • PRECISE SHARPENING: Variable-speed motor turns wheels 90 to 150 RPM..
  • COMPLETELY ENCLOSED MOTOR: Keeps debris and water from entering the machine..
  • VERSATILE OPERATION: Ideal for wood turning chisels, knives, and hand carving tools..
  • PREVENTS TEMPER LOSS: Water-cooled stone grinding wheel prevents tools from overheating..
Check Stock

10'' Two-Direction Water Cooled Sharpening System, DNYSYSJ Wet/Dry Stone Grinder 110V Electric Knife Sharpener with Adjustable Water Reservoir for Sharpening Chisels and Planer Blades 240W USA STOCK

  • ...or, Water Cooled Sharpening System, Features a 10-Inch 220 Grit Sharpening Stone and an 8-Inch Leather-stropping Wheel, The motor shell is made of aluminum alloy and has a long service life..
  • ★ 【Completely Enclosed Motor】Prevent impurities and water from entering the machine, Reverse the Rotational Direction with the Simple Flip of a Switch, Easy to use, It allows you to work at any angle without adjusting the motor position..
  • ★ 【Complete Equipment】Features an Onboard Carrying Handle, an Angle Guide, an Adjustable Water Reservoir, and a Jig for Sharpening Chisels and Planer Blades..
  • ★ 【Precision Sharpening Motor】Particle size of grindstone: 220mesh, 10 inch grindstone speed: 95 RPM, Motor Speed: 1425 RPM, The deep well slot design keeps the stones cool while reducing splash, making your work area cleaner..
  • ★ 【Multipurpose】Widely Used in Woodworking Hobby and Training, Slaughtering Meat, Catering Hotels, Leather Care, Pedicure and Pedicure, Clothing Sewing and Medicinal Material Slicing. You can contact us at any time if you have any questions. (U.S. inventor....
Check Stock

Tormek T-8 Drill Bit Sharpener Kit (Tormek T-8 Original + DBS-22 Drill Bit Sharpening Attachment) also Includes: SP-650, TT-50, SE-77, PA-70, WM-200, and Tormek Handbook. (US Version)

  • Includes: Tormek T-8 Original, SE-77 Square Edge Jig, PA-70 Honing Compound, TT-50 Truing Tool, WM-200 Angle Master, SP-650 Stone Grader, DBS-22 Drill Bit Sharpening Attachment.
  • Note: This low RPM machine operates at 115 volts and is designed to work exclusively in North America. If you plan on using this product in a country that operates at 220-240V, you will cause damage to the motor and machine..
Check Stock

WeldingCity 150 Amp Power Cable Hose 57Y03R 25-ft Rubber 1-pcs Style for Air-Cooled TIG Welding Torch 9/17 in Lincoln Miller ESAB Weldcraft CK Everlast AHP

  • Premium quality power cable hose for air-cooled and water-cooled TIG welding torch 9, 17, 18, 20, 25 and 26 series..
  • For air-cooled torches 9 and 17 series: standard Weldcraft style one-piece type rubber-jacketed power cable hoses 57Y01R (12.5-ft) and 57Y03R (25-ft....
  • For air-cooled torches 26 series: standard Weldcraft style one-piece type rubber-jacketed power cable hoses 46V28R (12.5-ft) and 46V30R (25-ft and....
  • For water-cooled torches 20 series: standard Weldcraft style power cable hoses (rubber-jacketed with fabric sleeve) 45V03R (12.5-ft) and 45V04R....
  • Compatible with most TIG welders from Lincoln, Miller, ESAB, Everlast, Eastwood, AHP, etc. US-based welding and hardware supplier. Strong technical....
Check Stock