Top Vertical Shaft Kiln Reviews

Playcraft Telluride Espresso 22’ Shuffleboard Table

3” – vertical stave, edge glued, kiln dried Russian Birch butcher block playfield with ¼” poured polymer surface.
24” stained hardwood overhead electronic scorer with plexi face.
Playing equipment includes, set of (8) 2-5/16” weights – 4 blue, 4 red, board sweep, speed wax and playing instructions.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6....
Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI.....
This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine....

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.

Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Split through flange and taper to provide strong clamping on the shaft.
Class 30 gray cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.