Top Uart Interface Reviews

Geniatech XPI-3128 Single Board Computer,Embedded Computer Module,Development Board ,Rockchip RK3128 Quad Core Cortex-A7 8GB WiFi ,Card-Sized High Performance Board

  • 85mm*56mm, Credit-card-sized High Performance Board.
  • 4*USB HOST, 1*HDMI Out, 1*Micro USB, 1*UART, 1*GPIO interface, WiFi and 100M LAN interface,Support Micro SD card.
  • Rockchip RK3128 with Quad-core Cortex-A7 up to 1.2GHz.
  • 40 Pin header enables hardware re-use by maintaining compatible alternate pin functions like I2S, I2C, PWM, UART, and GPIO. Form-factor compatible with Raspberry Pi 3 for easy migration..
  • Form Factor & GPIO Compatibility with Raspberry Pi for Maximum Re-usability.
Check Stock

FYSETC 3D Printer Parts Stepstick Mute TMC2209 V3.1 Stepper Motor Driver UART Mode with Heatsink for Reprap Ram1.4 MKS Gen/SKR V1.3 MKS GEN L Ramps 1.4/1.5/1.6 Control Motherboard-5Pcs

  • TMC2209 V3.1: ultra-silent motor driver, 2020 New Version, compatible to a number of legacy drivers as well as to the TMC2208, Support UART mode, compatible with popular motherboards such as FYSETC S6/F6, MKS SGENL, MKS GENL v2.0, MKS Robin E3D, SKRv1.3/1.4. Heat sink color is random: Blue or Black..
  • Upgrade Tips: add CLK pin, not connect in default, tie to GND via 0R.
  • SPREAD pin is floating. Reserve pull-up and pull-down resistors. Move TX from 3 to 5..
  • Advantage 1: StallGuard for sensorless homing. The integrated power MOSFETs handle motor currents up to 2A RMS with protection and diagnostic features for robust and reliable operation. A simple to use UART interface opens up tuning and control options. Store application tuning to OTP memory..
  • Advantage 2: Industries’ most advanced STEP/DIR stepper motor driver family upgrades designs to noiseless and most precise operation for cost-effective and highly competitive solutions..
  • Advantage 3: Step/Dir Drivers for Two-Phase Bipolar Stepper Motors up to 2.8A peak –StealthChop for Quiet Movement – UART Interface Option –Sensorless Stall Detection StallGuard4..
Check Stock

Rakstore Speak Recognition Voice Recognition Module V3 Compatible with for Arduino Support 80 Kinds of Voice DC 4.4-5.5 V High Accuracy

  • Digital Interface: 5V TTL level for UART interface and GPIO.
  • Analog Interface: 3.5mm mono-channel microphone connector + microphone pin interface.
  • Recognition accuracy: 99% (under ideal environment)；Size: 31mm x 50mm.
Check Stock

Beaster Voice Recognition Module with Microphone Dupont Jumper Wire Speech Recognition Voice Control Board for Arduino

  • This product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all..
  • This board has 2 controlling ways: Serial Port (full function), General Input Pins (part of function). General Output Pins on the board could generate several kinds of waves while corresponding voice command was recognized..
  • Digital Interface: 5V TTL level for UART interface and GPIO.
  • Analog Interface: 3.5mm mono-channel microphone connector + microphone pin interface.
Check Stock

Gowoops MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY

  • Embed version of Mega 2560 CH340G/ATmega2560 - compatible with Arduino Mega 2560 board..
  • Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
  • Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
  • The board used the chip CH340G as converter UART-USB..
Check Stock

DTECH FTDI USB to TTL Serial 3.3V Adapter Cable TX RX Signal 3 Pin 0.1 inch Pitch Female Socket FT232RL Chip Windows 11 10 8 7 Linux MAC OS 6ft Black

  • 6 ft USB to TTL serial adapter (with 3 pin 0.1” pitch female header socket) connects devices with 3.3 V logic level UART signals interface to a....
  • A genuine FT232RL chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates.
  • 6 feet FTDI USB to TTL serial cable (3 way output flying leads ) provides access to UART (transmit) Tx, (receive) Rx and GND.
  • FTDI chipset on the PCB board has configurable internal EEPROM and 3.3V UART signals can be individually inverted by configuring the EEPROM.
  • 3V3 TTL to USB converter cord is compatible with Windows 11, 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE, Mac OS, Linux 2.4 and greater.
Check Stock

DTECH USB to TTL Serial 3.3V Adapter Cable TX RX Signal 4 Pin 0.1 inch Pitch Female Socket PL2303 Prolific Chip Windows 10 8 7 XP Vista (6ft, Black)

  • 6 ft USB to TTL serial adapter (with 4 pin 0.1” pitch female header socket) connects devices with 3.3 V logic level UART signals interface to a laptop via USB port.
  • A genuine PL2303TA chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates.
  • 6 feet USB to TTL serial cable 3V3 (4 way output flying leads ) provides access to UART (transmit) Tx, (receive) Rx, VCC (5V) and GND.
  • PL2303 Prolific chipset on the PCB board has configurable internal EEPROM and UART signals can be individually inverted by configuring the EEPROM.
  • 4 pin 3.3V USB to TTL converter cord Compatible with Windows 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE.
  • ideal USB 2.0 debug cord for Vendor ID re-write, router, GPS, set top box, transmitter, flash firmware on hard drive, etc..
Check Stock

ACEIRMC 2pcs for MEGA 2560 PRO Embed CH340G/ATMEGA2560-16AU Chip with Male Pinheaders Compatible for Arduino Mega2560 Module

  • MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY.
  • Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
  • Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
  • Board for functionality similar to the compatible for Arduino Mega 2560..
  • The board used the chip CH340G as converter UART-USB..
Check Stock

SEEU. AGAIN 4pcs 0.96 Inch I2C OLED Display Module IIC SSD1306 128x64 LCD White with 4 Pin Female to Female Du-pont Wire

  • I2C mode up to 400Khz, configurable slave address.
  • Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
  • 4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
  • Backlight brightness and contrast controlled by software commands.
  • Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.
Check Stock

MakerFocus Lidar Range Finder Sensor Module TF-Luna, Single-Point Micro Ranging Module 0.2 to 8m Compatible with Pixhawk, Arduino and Rasppbarry Pi with UART / I2C Communication Interface

  • English product manual: Get the link in the product guide and document. Note: TF-Luna module comes with UART and I2C interface, the default is UART, if you need to use I2C interface, please set it yourself..
  • TF-Luna: TF-Luna is a single-point ranging LiDAR, based on TOF principle. With unique optical and electrical design, it can achieve stable, accurate and highly sensitive range measurement..
  • Product Characteristics: The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios..
  • Extreme Cost Performance: Low-cost ranging LiDAR module, with 0.2-8m operating range. TF-Luna has a highly stable, accurate, sensitive range detection..
  • Slim Figure Yet Big Skill: The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios..
Check Stock

ACEIRMC 2pcs ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 with Camera Module OV2640 2MP for Arduino (4pcs)

  • The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core.
  • ESP32-CAM WiFi Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card.
  • Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
  • Support OV2640 and OV7670 cameras, built-in flash.
  • Support image WiFi upload and Support TF card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module.
Check Stock

seeed studio Ethernet Shield

  • High-speed Ethernet controller W5200 with integrated Ethernet MAC & PHY.
  • Supply voltage: min: 4.75VDC, typical: 5VDC.
  • microSD card socket supports SD card in FAT16 or FA.
Check Stock

MELIFE ESP32-CAM WiFi + Bluetooth Module WiFi for ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card

  • Transmit power: 802.11b: 17+/-2 dBm (@11Mbps), 802.11g: 14+/-2 dBm (@54Mbps), 802.11n: 13+/-2 dBm (@MCS7).
  • Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
  • Support OV2640 and OV7670 cameras, built-in flash.
  • Support image WiFi upload and Support TF card.
  • Low-power dual-core 32-bit CPU for application processors.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Package Included: 1* ESP32-CAM Module, 1* Camera Module.
  • Operating Temperature: -20 -- 85 degree celsius.
Check Stock