DRELD Low Pressure LPG Propane Gas Fireplace Fire Pit Flame Failure Safety Control Valve Kit with 5/8” -18UNF Inlet Outlet Thermocouple Knob Switch, Fits for Gas Grill, Heater, Fire Pit
SIZE: 750 mm thermocouple with M8*1 threaded head. Bakelite knob OD 38mm, D shaft 6.1mm..
APPLICATION: The kit is suitable for low pressure repair control system for Gas Grill, Heater, Fire Pit, & Fireplace..
MATERIAL: The fire pit gas control valve kit is made of brass and plastic for durable use. Not OEM but fits OEM Standards..
HOW TO USE: Fix the valve on a plate or board of your grill or fire pit by the head screw and flange. Connect your inlet and outlet hose on inlet and outlet side. Fix the thermocouple nut M8 on the valve end tightly. Connect thermocouple and end thread well. Open gas by correct size knob and push your valve around 5-10s till the thermocouple head is heated enough. Release your hand and it works properly. If the gas valve shut off again when you release hand, then please check..
AFTER SALES SERVICE: The Propane Fire Pit Kit Replacement Part completed with a One-year Warranty. Should be there any question, please feel free to contact us..
Propane Tank Top Heater Safety Kit Replacement Parts Propane Gas Patio Heater Repair Replacement Parts Safety Faston Type Thermocoupler Safety Assembly Kit and Fd4 Dump Safety Switch Control
Propane Tank Top Heater Replacement Parts Safety Faston Type Thermocouple Safety Assembly Kit with FD4 Dump Switch Is a Repair Replacement Part for....
Fits prpane tank top heater for most brand like Mr Heater, Dura Heat, COSTWAY, REMINGTON,ProCom and other most tank top heater with white faston....
Thermocoupler length 20inches with one FD4 weak current tilt dump switch gas R≤10 mΩ.
Thermocoupler set includes two parts with white faston type....
The round ring terminal should be connect with the valve screw or any metal part.
Special Design for Gas heaters Outdoor heaters Gold plated connectors....
CE & CSA Approved safety thermocouple replacement parts for propane tank top heater. (Not suitable for Texsport heater or similar main control valve).
Hiland NG-HB Tall Natural G as Patio Heater, 41,000 BTU, 33\ Heat Shield, Built In Ground Fixtures, Hammered Bronze/SS
New Pilot assembly comes with thermocouple, venture tube and igniter and igniter wire.
Application for Tall Square Commercial Heater.
Igniter wire and thermocouple wire's are a total of 22" long.
Will also fit most Table Top heaters. PLEASE CAREFULLY COMPARE THE CONFIGURATION OF THIS PART WITH WHAT YOU ARE REPLACING..
All AZ Patio Heaters products include a one year warranty against manufacturer defects. We are one of the only suppliers in the US to maintain a complete line of replacements parts and a full service repair center.
120630-02 Pilot ODS for Vent Free Propane Gas Wall Heaters by DESA, Glo- Warm
The 120630-02 Pilot ODS assembly was used on many of the unvented LP Gas wall heaters and LPG unvented gas log sets and fireplaces..
The 120630-03 Pilot ODS assembly take the 120790-01 Dual Wire Thermocouple. The 120790-01 Thermocouple Dual Wire 33 Inch Length with silver and brown transmitter wires that fits the Desa International Unvented Vent-Free infrared gas wall heater..
Many of the Unvented Gas Logs sets, Wall Heaters and fireplaces that used the 120630-02 Pilot ODS were made by DESA International and sold under many different brand names by Lowe's, Ace Hardware, Home Depot, Sears, Menards Store and other retailer throughout North America.
Some of the Brand Names were Vanguard, Comfort Flame, Glo-Warm, Cozy Heat, Kozy World, Pro Com, Desa International and others..
Replaces part numbers: 098245-01, 098245-03, 099440-02, 099440-06, 107667-02, 110803-02, ene 56817, ene 70366, J5527 F.
Instrukart Dry Block High Temperature Calibrator AI-DBC 650 for Calibration Labs Pharmaceutical divisions Thermal Plants divisions Along with Calibration Certificate
Accuracy: ±0.6°C, Bath Stability: ±0.5°C.
Measuring Functions: J Type Thermocouple, K Type Thermocouple, T Type Thermocouple, R Type Thermocouple, S Type Thermocouple, N Type Thermocouple, MA, MV, Volts, Ohms, RTD (Pt 100).
Temperature Steps: 50°C, 150°C, 300°C, 450°C, 600°C.
Switch Test: Continuity check with OPEN / CLOSE indication.
Transmitter Supply: 24V DC ± 10% (Loop Powered).
Power Supply: 230V AC ± 5% / 50Hz, 500 W for 350UTC.
Supply Scope: Instrument, Power Cable, Carrying Case, Test Lead(2 & 3 Wire), Insertion Tube, Insertion Tool,Spare Fuses: 6A x 2nos User Manual, Calibration Certificate.
Cooper Atkins 35132 Aquatuff with Wrap&Stow Duraneed
Waterproof Thermocouple Thermometer - Precise digital thermocouple thermometer, delivers a true +/- 0.9 degrees Fahrenheit accuracy and probes can be replaced in the field without the need for recalibration.
Heavy Duty Probe Cable - Patented thermocouple thermometer probe cable that neatly wraps and stows around the instrument. Uses any K Type probe.
DuraNeedle Probes - Best used for dense meats. Also works well with soft foods and liquids. Probe is calibrated with instrument for Total System Accuracy.
Waterproof Digital Thermocouple - Large easy to read digital LCD display, auto shutoff after 10 minutes of non-use. IPX7 waterproof rated.
Cooper-Atkins Corporation - Headquartered in Middlefield, CT, Cooper-Atkins has been a leading manufacturer of quality time, temperature, and humidity instruments serving the Foodservice, HVAC and Healthcare markets since 1885.
pyrometer Temperature range: -50°C to 1300°C ( -58°F to 2372°F) and Overload display alert when input exceeds measurement range pyrometer. Thermocouple Temperature range: -50°C to 1000°C ( -58°F to 1832°F).
Designed for use with K-type thermocouples and Selection between Celsius and Fahrenheit.
Decimal or round number display selectable (decimal range is -58.0F to999.9F and round number range is -58F to 2372F).
Includes 2 Thermocouples ( One 3" K type temperature probe (-58 – 752 °F) and one Kiln Heavy duty K type Thermocouple ( -58°F to 1832°F) and Digital Pyrometer, 9V battery and Manual.
Thermocouple Measurement range: 32 - 1832 °F (0 - 1000 °C) Thermocouple Type: K Type Cable length : 3 ft Sensing tip length: 6" (150mm) Stainless Steel Sensing tip diameter: 0.19" (5mm) Thread width : 5/16" (M8) Internal Insulation: Fiber Glass External shielding: Metal Shield (Stainless steel braided).