Top Stucco Wire Lath Reviews

Strong-Point 86MZ 8 x 0.75 in Phillips Modified Truss R-W Head Screws Zinc Plated Box of 8 000

Meets ASTM A 510 for carbon steel manufacturing..
Multipurpose sheet metal screw for light to medium gauge applications..
Zinc plating meets ASTM B 633 for electrodeposited zinc coatings..
Material Application - Attaches wire lath to wood or light gauge metal..

Check Stock

Stainless Steel Lath Screws, 8 x 1-5/8, Sharp Point Modified Truss Head Phillips Drive (Quantity: 100) Type 17 Cutting Point 305 (18-8) Stainless Steel, Length: 1-5/8 (1.625) in.

Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Check Stock

Stainless Steel Lath Screws 8 x 1-1/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 1-1/4 1.25 in.

Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Check Stock

Max HN120 PowerLite Concrete Nailer

✅ Shoots 14 gauge T-nails from 5/8'' to 2-1/2'' long | Hardened driver | Convenient side-load magazine | Rubber hand grip for added comfort | Heavy-duty light weight aluminum body | Adjustable exhaust.
✅ Soft grip handle reduces fatigue | Touch-strike security system is safe for the operator | Available with either sequential and contact fire trigger | Quick-release nosepiece for fast clearing of jams | Rubber can protect the surface of the gun when the gun fall.
✅ Magazine Capacity: 100 | Operating Pressure: 80-100 PSI | Air Inlet: 1/4" | Fastener Size: 14 Gauges - 0.087" Diameter | Fastener Type: T-Nails (both hardened & galvanized) | Fastener Length: 5/8" - 2-1/2" Long Nails.
✅ Includes: Concrete T-Nailer | Cardboard box.
✅ Wood to concrete & masonry furring | Plywood to concrete nailing | Light gauge steel drywall track to concrete | Wire lath to masonry | Steel banding to wood | Wood to light gauge steel (up to 3/16") | Decking | Fencing | Sub flooring | General construction.

Check Stock

2000 Pcs #8 x 1 K Lath Mod Truss Sharp Point 305 SS ACQ Rated Low Profile Deck Screw - U-Turn

#8 x 1" K Lath Mod Truss Sharp Point 305 SS ACQ Rated Low Profile Deck Screw.
A steel fastener with an extra wide head, twinfast thread, and a piercing point. Common Usage is to attach lath to wood studs or light gauge metal..
305 STAINLESS STEEL - A Nickel-Chromium grade of stainless steel that is used outdoors for high corrosive applications. ACQ Compatible.
Head Diameter: .404" - .441" | Head Height: .070" - .083".

Check Stock

MILWAUKEE'S Rl Hole Saw, Carbide Grit, Black, 4-3/8 In (49-56-0300)

4-3/8 in. diameter 1-3/4 in. depth of cut.
For cutting through drywall, plaster, acoustical tile, ceiling tile and stucco with wire mesh backing.

Check Stock

SnakeBit Drill 3/8\ x 18\ Masonry Cable Installer Drill Bit – Carbide Tipped Hollow Shank Bellhanger Drill Bit - MADE IN USA

3/8" x 18" Hollow Shank Installer Drill Bit - Masonry Tipped - Easily cuts through concrete, cement, brick, stucco.
PATENTED HOLLOW SHANK - Eliminates the need to pull wire backwards through walls. Allows the user to install wire in the same direction they are working.
COMMON USES - RG58, RG59, RG6, Cat5, Security Systems, HDTV, Phone Lines.
USED BY - Cable Installers, Phone Companies, Security Companies, Electricians, HVAC, Home Owners, DIY.

Check Stock

Milwaukee Electric Tool 49-56-0305 Recessed Light Hole Saw, 6-3/8\ D

For best results, 600 RPM is recommended.
6-3/8 in. diameter 1-3/4 in. depth of cut.
For cutting through drywall, plaster, acoustical tile, ceiling tile and stucco with wire mesh backing.

Check Stock

#8 x 3/4' Hex Washer Head Self-Drilling Tek Screw Zinc Plated Steel for Attaches Sheet Metal Steel or Steel to Metal - Box of 100

HIGH QUALITY ZINC-PLATED STEEL: Phillips Modified Truss Head Sheet Metal Screw made of 100% high quality durable steel with hard Zinc Plating, built to last years with no wear and tear.
RUST RESISTANT: Zinc Plating provides an excellent corrosion resistant shell for a long lasting cost effective fastener.
CONVENIENCE: Phillips Modified Truss Head Sheet Metal Screws are known to be convenient and versatile. Great to have while working with sheet metal environment. Suitable for indoor and outdoor applications.
For use in Sheet Metal Steel, Attaches Wire Lath to Metal Studs or Metal or Aluminum to Metal or Aluminum. Installed with #2 Phillips Driver.
Amazon Protected Money-Back Satisfaction Guaranteed.

Check Stock

1" Scotch Eye Wood Auger Drill Bit For Bushcraft and Camping | Hand Auger | For Bushcraft Backpack | Perfect Addition To Survival or Camping Gear Packs |

3/8" x 18" Hollow Shank Installer Drill Bit - Masonry Tipped - Easily cuts through concrete, cement, brick, stucco.
PATENTED HOLLOW SHANK - Eliminates the need to pull wire backwards through walls. Allows the user to install wire in the same direction they are working.
COMMON USES - RG58, RG59, RG6, Cat5, Security Systems, HDTV, Phone Lines.
USED BY - Cable Installers, Phone Companies, Security Companies, Electricians, HVAC, Home Owners, DIY.

Check Stock

#8 x 1/2\ Phillips Modified Truss Head Self-Drilling Tek Screw, Zinc-Plated Steel for Sheet Metal Attaches Wire Lath to Metal Studs - Box of 100

HIGH QUALITY ZINC-PLATED STEEL: Phillips Modified Truss Head Sheet Metal Screw made of 100% high quality durable steel with hard Zinc Plating, built to last years with no wear and tear.
RUST RESISTANT: Zinc Plating provides an excellent corrosion resistant shell for a long lasting cost effective fastener.
CONVENIENCE: Phillips Modified Truss Head Sheet Metal Screws are known to be convenient and versatile. Great to have while working with sheet metal environment. Suitable for indoor and outdoor applications.
For use in Sheet Metal Steel, Attaches Wire Lath to Metal Studs or Metal or Aluminum to Metal or Aluminum. Installed with #2 Phillips Driver.
Amazon Protected Money-Back Satisfaction Guaranteed.

Check Stock

CREWTOWER Roofing Nail Gun, 15 Degree 3/4-inch to 1-3/4-inch Pneumatic Roofing Nailer, Heavy Duty Coil Roofing Nailer for Asphalt Fiberglass Shingles Lath Wire Fasterening Wooden Box Assembly

[Professional Nail Gun]: This roofing tool is made not only to get your work done, but also as a loyal servant to your beautiful life and dreams. This roofing nail gun is the right tool to assist you achieve those goals..
[Easy to Use]: With easy-to-load magazine, this roofing nailer is easy to load coil roofing nails. The quick-release nosepiece makes it easy to clear jams. Simply turning a wheel, you can adjust the nailing depth, and interchangeable trigger to switch firing mode..
[Powerful and Efficient]: This powerful air nailer is made of industrial-grade parts, firing engine provides quick response. Comfortable rubber handle and well balanced siding nailer gun body reduces fatigue for long time jobs. Large capacity magazine improves working efficency by minimizing replenishment time..
[Wide Applications]: This heavy duty coil roofing nailer is ideal for fasterning asphalt and fiberglass shingle, fasterning lath wire on plywood, siding installation and wooden box assembly..
[Tool Specifications]: The pneumatic coil roofing nail gun weighs only 5.67lbs with aluminium body, load capacity 120 nails, drives 15 degree wire welded coil roofing nails, nail length 3/4" to 1-3/4", shank diameter 0.12", air-powered, operating pressure 70-120PSI..

Check Stock

Simple Designs LT2004-BWN Texturized Curvy Ceramic Table Lamp, Brown

Perfect for living room, bedroom, or office.
Uses 1 x 60W Type A Medium Base Bulb (not included).
A charming and practical table lamp to meet your fashion lighting needs. This lamp features a texturized stucco ceramic base and matching fabric shade. Perfect for living room, bedroom, or office..
Uses 1 x 60W Medium Base Bulb (not included).

Check Stock