Top Oxygen Sensor Tool Reviews

MIROZO 234-4092 Oxygen O2 Sensor Downstream for Acura NSX 1995-1999, for Honda Civic 2001-2005, for Honda Odyssey 1996-1998, for Honda Prelude 1997-2001 1PCS

TIPS: If you are not sure whether this product is suitable for your model, please check detail page, or inform us your vehicle part number to let us check for you.Oxygen (O2) Sensors commonly fail due to contamination. When checking or replacing an O2 Sensor, visually inspect the sensor body to determine if it has been contaminated by a faulty part or substance upstream, and correct the fault before replacing the sensor..
FEATURES OF THE MIROZO OXYGEN SENSOR - Internal Ceramic Insulation for optimal sensor performance.
Laser welded sensor body to keep out contaminants.
Dual Insulated Protective Cover Prevents premature zirconium sensor wear.
Sealed wire leads prevent water interference with electronic signal..
ADVANTAGES OF THE MIROZO OXYGEN SENSOR: Improve Engine Response & Performance.
Prevent premature failure of the catalytic converter..
An OBD Scan Tool will usually identify Oxygen (O2) Sensors by the Bank Number (B1 = Bank 1.
B2 = Bank 2) and Sensor Number (S1 = Sensor 1.
S2 = Sensor 2, etc.). Bank 1 is not on the same side of the engine for every vehicle. Bank 2 refers to the bank opposite Bank 1. Sensor 1 refers to the sensor before the catalytic converter. Other Terms: Upstream Sensor, Pre-Cat....

Check Stock

Walker Products 350-34099 Oxygen Sensor Original Equipment Replacement O2 Sensor Pack of 1

Walker Products Oxygen Sensor Program is the Industry Leading OEM and Aftermarket Oxygen Sensor ( O2 Sensor ) Program.
Walker O2 Sensor is Manufactured to meet and exceed OE specifications.
increase fuel efficiency, decrease emissions,....
Backed by Walker Products buyer protection for worry free installation and performance.
To ensure this product fits your vehicle please use the AmazonConfirmedFit tool.

Check Stock

8MILELAKE 10pcs Oxygen Sensor Socket Set Sensor Oil Pressure Sending Unit Socket Set

10Pcs Sensor Oil Pressure Sending Unit Socket Set Oxygen Injection Tool Set Remove Oxygen.
Sensors, Injectors, Oil Pressure Sending Units And Vacuum Switches. Heat-treated Chrome.
Vanadium And Chrome Molybdenum Steel With Black Oxide Finish Accepts Either 3/8 Or 1/2"".
Drive Ratchet Depending On The Size of The Socket 10Pc Oxygen Sensor & Diesel Injection Oil.
Pressure Unit Vacuum Switches Socket Set Heat Treated Chrome Vanadium & Chrome Molybdenu.

Check Stock

Replacement Car Exhaust Back Pressure Tester Gauge Meter DiagnosticTool Catalytic Converter Clog Test Gauge Kit

Car Exhaust System Back Pressure Tester Meter Diagnostic Tool Exhaust System Diagnostic Tool Exhaust Back Pressure Tester.
Adaptor fits into oxygen sensor hole enabling back pressure of mufflers and catalytic converters.
Gauge adapter threads into oxygen sensor ports (both 12mm and 18mm). Test at idle and at2500 rpm's. Pressure should be below 1.25psi at idle and below....
Higher readings indicate a restriction which should be corrected..
Package including? 1* SET OF Car Exhaust System Back Pressure.

Check Stock

GEARWRENCH 8 Pc. Sensor and Sending Socket Set - 41720

Designed for the removal and installation of oxygen sensors, oil pressure sending units, and vacuum switches.
Includes 3/8" drive 7/8" slotted socket for PVS, TVS and O2 sending units.
Includes 3/8" Drive 7/8" (22mm) socket for Oxygen Sensor Units.
Includes 3/8" Drive 1-1/16" Deep socket for Oil Pressure Sending units.
Includes 3/8" Drive 7/8" (22mm) Low Profile Offset socket for O2 Sensor Unit.
Includes 1/2" Drive 1-13/16" socket for Oil Sending Unit.
Includes 1/2" Drive 1-1/16" socket for Thermal Sensor units.
Durable blow mold case for safe storage and tool retention.

Check Stock

ITEQ 7/8 Inch (22 mm) 6-Point by 1/2 Inch Drive Offset Oxygen Sensor Socket with Wide Side Cutout for Preventing Damage to Wires

Perfect tool for removing, inspecting, replacing and installing heated and non-heated oxygen sensors on most vehicles with computer-controlled engines.
The 6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 1/2” drive and 7/8” ends can be used with both ratchet and torque wrench.
The oxygen sensor socket's special side cutout design allows easy access to oxygen sensors from any section and prevents damage to wires.
Made of high-quality Chrome vanadium steel for extra strength and durability.
Suitable for oxygen sensors found on most modern vehicles.

Check Stock

aremnry 7pcs O2 Oxygen Sensor & Oil Pressure Sending Unit Master Sensor Socket Set Vacuum Switch Socket Removal Installer Tool Kit

【Applications】 Designed for the removal and installation of oxygen sensors, oil pressure sending units and vacuum switches equipped with wires or vacuum tubes..
【Material Solid】 Heat treated chrome vanadium & chrome molybdenum steel (CR-V) with black oxide finish for corrosion resistance..
【Including】7/8" Short low Profile O2 Oxygen Sensor Socket, 7/8" Universal Oxygen Sensor Socke 7/8" Universal Vacuum Switch PVS, TVS Socket Tool..
【Function】 This set can work in the tight space around an O2 sensor to remove or install quickly and efficiently..
【Easy Storage】Comes in a blow molded case for safe & easy transport and storage..

Check Stock

ABN Oxygen 02 Sensor Socket 7-Piece Tool Kit – 22mm (7/8in), 27mm, 29mm – All Vehicle O2 Removal and Installation

NO MORE HASSLE: The ABN Oxygen 02 Sensor Socket 7-Piece Tool Kit – 22mm (7/8” Inches), 27mm, 29mm – All Vehicle O2 Removal and Installation is for inspection, removal, and installation of hard-to-reach oxygen sensors, oil pressure switches, oil pressure sending units, thermal sensor switches, vacuum switches, and brake light switches.
Each socket is permanently etched with size marking for your convenience.
MATCHES YOUR CAR: Universal fit for Audi, BMW, Citroen, Mercedes, Peugeot, Renault, Skoda, Vauxhall/Open (GM), and Volkswagen.
Sizes include 22mm (7/8”), 27mm, and 29mm.
For both heated and non-heated oxygen sensors.
Compatible with 3/8-inch and 1/2-inch ratchet drivers or extensions.
Side cutout sections allow the sockets to fit over wiring harness and prevent damage to wires.
BUILT TO LAST: Constructed from chrome-vanadium steel (CR-V) for extra strength and longevity.
Tools have a light coating of oil to protect them from rusting.
EASY STORAGE: Heavy-duty 9” x 2.25” x 8” inch (22.9cm x 5.7cm x 20.3cm) plastic blow-molded carrying case for easy transportation, safe storage, and quick organization.
CONTENTS: Package includes (1) 29mm pressure/vacuum switch 6pt socket + (1) 22mm (7/8 inch) vacuum switch 6pt socket + (1) 22mm (7/8 inch) v....

Check Stock

ITEQ 5 Pcs Automotive Oxygen Sensor Socket Wrench Remover Tool and Thread Chaser Set

Perfect tool set for removing, inspecting, replacing and installing heated and non heated oxygen sensors and vacuum switches on most vehicles with computer-controlled engines.
3 types of universal socket wrenchs cover various situations of oxygen sensor location.
6-point 7/8” (22mm) socket opening fits all hexagon oxygen sensor, common 3/8” and 1/2” drive ends can be used with ratchet or breaker bar.
Special side cutout design allows easy access to oxygen sensors from any section and prevents damage to wires.
Set Including: 1-pc 3/8” Dr. extra deep broach socket (3-1/8” long), 1-pc 3/8” Dr. low-profile crowfoot socket wrench (1-1/4” long), 1-pc 1/2” Dr. offset crowfoot socket wrench (1-15/16” long), 1-pc M18 x 1.5mm and 1-pc M12 x 1.25mm thread chasers with 3/8” drive to clean and repair damaged threads.

Check Stock

3/8-Inch Drive Oxygen Sensor Socket Offset Wrench Remover Tool

PackageIncludes 2 7/8" 3/8 Inch Drive Vacuum Switch Sockets and One 7/8" x 1/2" drive Oxygen Sensor Socket.
Design Standard 6 point with low profile and slotted design to enable you remove oxygen sensors with the wiring harness still attached, and the socket is offset and compact which allows extra leverage even in hard to reach spots..
Material Made from high performance chrome molybdenum and solid cast steel construction for strength and durability - Finished with Black Oxide to prevent rust..
Usage Built for use with ratchets and breakers bars to remove and install oxygen sensors and hex vacuum switches on vehicle, even if you don't have a lot of experience working with cars. This high quality tool can save your time!.
Service 100% satisfaction guarantee, If you have any issues with the oxygen sensor socket, simply contact customer service for troubleshooting help, parts, replacement, or refund. Our aim is to make you satisfy the parts and the service we provide for you..

Check Stock

3/8-Inch Drive Oxygen Sensor Socket Offset Wrench Remover Tool fits All Vehicle O2 Removal and Installation Universal Puller and Removal Tool

REMOVE OXYGEN SENSORS FROM YOUR VEHICLE: This 10 Piece Specialty Sockets O2 Sensor Tool Set lets you quickly and easily remove oxygen sensors, oil pressure sending unit, fuel injectors, and vacuum switches.
Some O2 socket pieces feature cutout sides to prevent damage to wires and tubes.
Remove and install parts on most domestic and some international vehicles.
USE WITH YOUR TOOLS: Features 3/8-inch or 1/2-inch square drive to fit your O2 sensor wrench drives.
For use with ratchet, breaker bar, or hand wrench (driver tools not included).
Use this tool in conjunction with the O2 Sensor Thread Chasers to install new sensors easily (thread chaser and sensors not included).
BUILT TO LAST: Constructed of heat-treated chrome vanadium steel, this oxygen sensor remover set is built for strength, durability, and longevity.
Each 02 sensor socket is coated with a black oxide finish to provide resistance to rust and corrosion.
CONTENTS: This specialty tools set includes 10 pieces: 1/2 inch dr x 22mm x 6PT x 110mm, 1/2 inch dr x 29mm x 6PT x 90mm, 1/2 inch dr x 22mm x 12PT x 78mm, 1/2 inch dr x 27mm x 12PT x 78mm, 1/2 inch dr x 28mm x 12PT x 78mm, 1/2 inch dr x 7/8” x 50mm, 3/8 inch dr x 7/8” x 6PT x 80mm, 3/8 inch dr x 7/8” x ....

Check Stock

EWK 22mm 7/8 Inch O2 Oxygen Sensor Flex Head Wrench Removal Tool

【 Flexible Operation 】Goes into narrow space and odd angles with the unique contour handle. EWK oxygen sensor removal tool works around the exhaust and gets to places ordinary wrenches won't. Easy to remove or install the hard-to-reach and stuck O2 sensors..
【 Extra Leverage 】Swiveled head helps create extra leverage in narrow areas. The 22mm oxygen sensor wrench helps getting additional clearance during the job. Effortlessly turns the removal job into a breeze..
【 Slotted Design 】 Get to the O2 sensor from the side to prevent damaging the wire or the sensor. Keeping the wire harness attached by getting to the sensor from the side instead of from the top..
【 Great Compatibility 】EWK O2 sensor remover is designed to work on 7/8″(22mm) O2 sensors. Compatible for Ford contours, 4.6L, 5.4L Ford modular engines. Covers most vehicles on the market..
【 EWK Assurance】Excellent WorKing experience guaranteed! EWK provides you premium quality tools and the best service with 12 months warranty. If there is any problem or concern with our products, please contact us for assistance..

Check Stock

Tribus Tools Oxygen and NOx Sensor Wrench (15/16\)

[SIZE]: 3 piece 3/8 & 1/2" drive O2 oxygen sensor wrench socket tool set.
universal 7/8"/22mm professional grade removal tool for cars & automotive.
[ITEM INCLUDES]: 1 vacuum switch socket & 2 puller sockets kit.
[MATERIAL]: Constructed of high performance (cr-v & cr-mo) vanadium and chrome molybdenum solid cast steel for strength and durability - finished with black oxide to prevent rust.
[APPLICATION]: Remove and install oxygen sensors and hex vacuum switches on vehicles.
[PACKAGE]: Packed in a blow-molded storage case.

Check Stock