Top Motor Driver With I2c Reviews

KEYESTUDIO L298P Motor Driver HAT Shield GPIO for Raspberry Pi Model B/B+/A+/2/3/4 Zero and Zero W, High-Power Motor Speed Control Board Dual H Bridge with IR Receiver

  • This Motor Driver HAT gives your Raspberry Pi the ability to drive two DC motors, with drive current up to 2A..
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards like Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions.
  • Reserved I2C SPI control pins, allows to work with other control boards and sensors. Comes with an IR receiver for communication with an infrared remote controller..
  • Included 4x M2.5*20MM screws, 4 xM2.5*10MM copper pillars, 4x M2.5 Nuts. Easy to install on your RPi board. Please note Raspberry Pi board, remote control and motors in the photos are Not Included!.
Check Stock

Servo Driver HAT 16-Channel 12-bit I2C Interface PWM Outputs for Jetson Nano Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B Supports SG90 MG90S MG996R etc @XYGStudy

  • Servo Driver HAT for Raspberry Pi, 16-Channel, 12-bit, I2C Interface.
  • Needless to say, the Raspberry Pi is powerful enough in most cases, yet it's not that good at providing precise PWM output. You may have tried to....
  • Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later version, Jetson Nano.
  • I2C controlled, using only 2 pins Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Check Stock

AITRIP 12PCS TCA9548A I2C IIC Multiplexer Breakout Board Module 8 Channel Expansion Development Board for Arduino

  • The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
  • Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
  • 12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.
Check Stock

DORHEA 10PCS 0.91 12832 IIC I2C OLED Display Module 0.91inch I2C 128x32 SSD1306 LCD Display Module White I2C OLED Screen Driver DC 3.3V/5V with 4 Pin Headers for Ardu ino

  • 0.91 inch OLED display, no need backlight, self-illumination, Display Color : White, Resolution: 128 x 32..
  • The I2c OLED display performance is better than the traditional LCD display, also lower consumption, high resolution OLED for any of your micro....
  • The 0.91 display performance is better than the traditional LCD display, it uses the very common I2C bus, and runs on the SSD1306 display driver..
  • 0.91 oled compatible with Ardu ino, ESP8266, ESP32, STM32, etc.
  • The 12832 display can run on 3.3v. It is legible, even with 4 lines of text. Highly recommended for projects that require some form of user interface..
Check Stock

OSOYOO Smart House IoT Starter Kit for Arduino MEGA2560,Learning STEM Electronic Engineering Coding Programming, DIY Home Automation Building Set for Teens Adults

  • ...programming, IoT, and home automation. Based on the Arduino mega2560..
  • INCLUDES TUTORIALS: Learn how to assemble, code, program, and automate each home feature and device with easy to follow step-by-step tutorials. All the necessary programs, libraries, codes, software and driver installation files are also included in this starter pack..
  • APP CONTROL FEATURES:Use OSOYOO IoT APP to remotely control devices.please download it by searching 'OSOYOO iot udp robot car app' from Apple Store or Google Play Store(Android device)..
  • INCLUDES EVERYTHING YOU NEED: Includes Everything You Need To Build & Engineer Your IoT Home Kit: Wooden House Model, OSOYOO MEGA2560 Board, MEGA IoT Extension Board with an ESP12s wi-fi module, and various home automation devices: RFID, Flame Detection Modules,LED, Temperature & Humidity, PIR Motion Ultrasonic, Micro Servo Motor, 1602 I2C LCD Module, Button Modules, RGB Photosensitive, Buzzer, PnP Jumpers, Cables, & More..
Check Stock

DORHEA 2Pcs BME280 5V Temperature Humidity Atmospheric Barometric Pressure Sensor Module GY-BME280-5V IIC I2C Breakout Board

  • The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
  • BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
  • Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
  • The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
  • The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..
Check Stock

Aoicrie 5pcs PCA9685 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit, for Robot or for Raspberry pi Shield Module servo Shield

  • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)..
  • Communication Interface: IIC, PCA9685 contain an I2C-controlled PWM driver with a built-in clock..
  • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs..
  • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate..
  • 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or for Raspberry pi shield module servo shield..
Check Stock

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

  • 【Brussless Spindle Motor】Power: 400W.
  • Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
  • 【Brussless Spindle Motor Driver】Maximum driver power: 600W.
  • Maximum driver motor running speed: 12000R/Min.
  • Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
  • The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....
Check Stock

16x2 Blue LCD Module Controller HD44780 Based for Arduino by Corpco

  • Size: 1.54in screen can provide clear view for you..
  • Drive Voltage: 3.3V-5V. The pin has good contact performance, ensure stable working.
  • Material: Adopted of high quality electronic components, and preciseness process, ensure for the durability.
  • Resolution: 128 x 64. Great workmanship, easy and convenient to install. Driver IC: SSD1309, compatible with SSD1306. Interface: SPI interface I2C interface.
  • Optional Style: Display White, Display Yellow, Display Blue. Available in three colors for your choice..
Check Stock

SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V

  • Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
  • 3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
  • The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
  • I2C communication uses an open drain signaling, so there is no need to use level shifting..
  • The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
Check Stock

2 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module Blue I2C OLED Screen Driver DC 3.3V - 5V

  • What you will get: you will get 2 OLED display modules with classic display colors, self illumination with no need of backlight.
  • Power-saving display: the I2C OLED display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications)....
  • More details: this I2C LCD display is compatible with Arduino, ESP8266, ESP32, STM32, etc., 3.35V power.
  • Operating temperature: -40 - 85 degree....
  • Good compatibility: this I2C OLED display module is compatible with Raspberry Pi 4B/ 3B+/ 3B/ 2B/ Zero, compatible with Arduino, also compatible with....
  • Product manual: as shown in the instructions.
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

  • 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
  • Stepper motor with a standard interface could be connected with Driver Board easily.
  • A, B, C, D four-phase LED indicates the status of the stepper motor work..
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
  • Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.
Check Stock