Top Intake Manifold Runner Control Valve Reviews

Dorman 615-380 Engine Intake Manifold for Select Buick/Chevrolet Models OE FIX

  • Improved design - this intake manifold has been redesigned to correct a common PCV valve failure in the original equipment design to reduce excessive....
  • Complete kit - this manifold includes a new throttle body gasket, port gaskets, fuel injector O-rings, MAP sensor O-ring and screws for a complete....
  • Quality American construction - this intake manifold is engineered and manufactured in the United States of tough nylon polymer to resist cracking and....
  • Related repair - this manifold often leads to failure in the valve cover's PCV diaphragm.
  • a damaged valve cover will often need to be replaced at the....
  • Ensure fit – to make sure this part fits your exact vehicle, input your make, model and trim level into the Amazon Garage.
Check Stock

New MLS Head Gasket Set, Head Bolt Kit, Intake & Exhaust Engine Valves Compatible with 99-05 SAAB/SUBARU 2.5L 2458CC H4 SOHC, (16 Valve),”EJ25″

  • Aftermarket OE Replacement : Meets or exceeds OE standard quality and performance requirements..
  • COMPATIBLE WITH: 1999-05 Subaru Saab 2.5L 2458CC H4 “SOHC” (16-Valves) Eng.Code “EJ25”.
  • Includes : MLS (Multi-Layered Steel) Head Gasket (Improved Design) Intake Manifold Gaskets Exhaust Manifold Gaskets Valve Cover Gaskets Spark Plug Tube Seals Grommets Viton Valve Stem Seals Camshaft Front Seals Circular Plug (Valve Cover) EGR Valve Gasket Throttle Body Mounting Gasket Other Small Gaskets, Seals, And O-Rings Head Bolt Set (12 Pcs) RTV Gasket Silicone (Silicone brand may vary depending on availability) Intake & Exhaust Valves (16 Pcs).
  • Note : Upper Intake Manifold Gaskets (Plenum Gaskets) are “NOT” Included.
  • CONFIRM THIS PART FITS YOUR VEHICLE BEFORE PURCHASING (Check Fitment Data Above).
Check Stock

HOLLEY MODULAR LO-RAM EFI MANIFOLD KIT,TOP-FEED PLENUM,BLACK FINISH,COMPATIBLE WITH GM LS1,LS2 & LS6 GEN III & IV ENGINES

  • Brand New Holley Modular Lo-Ram EFI Manifold Kit, Top-Feed Plenum, Black Finish, Compatible with LS1, LS2 & LS 6 Gen III & IV Engines (Part #300-620BK).
  • The 300-620 top-feed plenum entry configuration is designed to allow the included Hi-Ram 105mm plenum top to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications was conceived to package with an air to water plenum mounted intercooler with a shorter overall height than possible with other existing intake manifolds..
  • The Holley LS1/2/6 Lo-Ram intake manifold kits are designed for GM LS Gen III & IV engines equipped with GM LS1/2/6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The fuel rail kits come with 2 sets of brackets: A set for long (usually standard length) fuel injectors & set for short (such as Pico, or LS7) fuel injectors..
  • NOTE: Total Height: Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top - 9.07" (without intercooler installed) | Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top, w/ intercooler installed - 9.07" + intercooler thickness.
  • Specs: Brand: Holley EFI | Color: Black | Construction: Cast | Emission Code: 3 ....
Check Stock

Intake Manifold Runner Control Bushing Set of 5 fits Ford fits Lincoln Mercury

  • Fitment Notes: Fitment Notes5 Piece Set, 2004-07, fits Ford Freestar Intake Manifold Runner Control Bushing.
Check Stock

Skunk2 907-05-9051 Ultra Series Intake Manifold Spacer

  • BBK is your Number One Aftermarket Performance Brand in the USA - American Designed and Built.
  • Non Heat Transfering Phenolic Material Reduces Upper Intake Manifold Temepratures for Reduced Air Intake Temperatures.
  • Cooler Intake Temperatures Allow Denser Air For Improved Performance.
  • Offers Increased Valve Cover Clearance for Larger Rockers and Valve Covers.
  • Easy to Install - Includes New Longer Hardware and 2 New Gaskets.
Check Stock

AUCERAMIC Replacement for Intake Manifold with Runner Control Valve and Air Pressure Sensor Fit for Dodge Avenger Journey Caliber Chrysler Sebring 1.8L 2.0L 2.4L

  • PACKAGE INCLUDE:1 Intake Manifold with Gasket,1 Runner Control Valve,1 Air Pressure Sensor..
  • PART NUMBER: 4884495AJ,4884495AK,4884495AG,4884495AH,4884495AF,4884549AC,4884549AD,4884550AB,4884883AA,MS19561,911-902.
  • REPLACEMENT FOR:Fit 2008-2011 for Dodge Avenger 2.4L,2009-2011 for Dodge Journey 2.0L,2007-2009 for Dodge Caliber 1.8L,2007-2010 for Chrysler Sebring L4 2.4L N/A..
  • OE STANDARD:Highly durable marerial to meet or exceed OE standard quality and performance requirements. Fits well and high performance make your car more horsepower..
  • DURABLE TO USE:The gasket with upgrade materials to ensure a perfect seal with no risk of leaking.Heat stabilized nylon providing better resistance to cold or hot cycles and further prevent cracking..
Check Stock

Small Block F-ord Intake Manifold - 351W Aluminum Carb Intake Manifold 1500-6500 Satin E42458

  • Our LowRise manifold for 351w engines is the ultimate street performance manifold for this engine.
  • Its long runner dual plane design provides the best of both worlds.
  • It provides good top end power without sacrificing bottom end torque..
  • This manifold has a number of features not found in similar competitive manifolds. It includes a rear water crossover passage which can provide for more balanced cylinder head temperatures and a cooler running engine.
Check Stock

BBC Holeshot Dual Plane Intake Manifold Oval Port, Plain

  • This Holeshot Manifold by Speedway Motors is the lowest profile intake design.
  • It is the perfect improvement over stock intake manifolds without worrying about hood clearance.
  • Manifolds are a dual-plane intake runner design and machined to accept spread port carburetors.
  • Has a idle-5500 rpm range and an oval port.
  • Features an aluminum construction with a natural finish.
Check Stock

Dorman 264-968 Engine Valve Cover Compatible with Select Buick/Cadillac/Chevrolet Models

  • Direct replacement - made from injection molded polymer for superior fit and heat resistance, this valve cover matches the original equipment part for fit and function.
  • Complete solution - this valve cover includes a new gasket and new bolts for a complete repair.
  • Quality tested - this part has undergone try-on and material testing to ensure a quality fit and reliable service.
  • Related repair - this valve cover often fails due to a faulty intake manifold.
  • also replace manifold if it is missing PCV valve.
  • Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check Stock

BBK 1506 3/8\ Phenolic Intake Manifold Spacer Kit for GT-40 and Cobra EFI Intake Manifolds

  • BBK is your Number One Aftermarket Performance Brand in the USA - American Designed and Built.
  • Non Heat Transfering Phenolic Material Reduces Upper Intake Manifold Temepratures for Reduced Air Intake Temperatures.
  • Cooler Intake Temperatures Allow Denser Air For Improved Performance.
  • Offers Increased Valve Cover Clearance for Larger Rockers and Valve Covers.
  • Easy to Install - Includes New Longer Hardware and 2 New Gaskets.
Check Stock

BBK 1520 3/8\ Phenolic Intake Manifold Spacer Kit for Edelbrock Performer EFI 5.0L Intake Manifold

  • BBK is your Number One Aftermarket Performance Brand in the USA - American Designed and Built.
  • Non Heat Transfering Phenolic Material Reduces Upper Intake Manifold Temepratures for Reduced Air Intake Temperatures.
  • Cooler Intake Temperatures Allow Denser Air For Improved Performance.
  • Offers Increased Valve Cover Clearance for Larger Rockers and Valve Covers.
  • Easy to Install - Includes New Longer Hardware and 2 New Gaskets.
Check Stock

CATUDIY Intake Pipe Valve Cleaner Machine for Car Engine Fuel System Cleaners, Fuel Cleaning Tool Automotive Engine Carbon Deposit Cleaner 110V Valvetronic System Walnut Powder Sand Carbon Deposition

  • Intake Pipe Valve Cleaning Machine -- An advanced equipment (3-Year Warranty) used to deeply remove highly sticky carbon deposits on the engine intake manifold and intake&exhaust valves. Regular carbon cleaning keeps the engine in healthy condition so as to provide high quality power continuously (Solve the problems of unstable idling, insufficient fuel combustion, and reduced air-fuel ratio).
  • Working Principle of Engine Cleaner -- Close the intake valve and then spray walnut powder into engine intake via air pump, while it will recycle the walnut powder through vacuum. This is a closed loop. Walnut powder will impact the carbon deposits on the inner wall of the intake pipe. After thousands of impacts, carbon deposits will be clear thoroughly.
  • Safe & Efficient -- As an eco-friendly pure natural polish material, walnut sand has advantages of hardness, pressure resistance and wear resistance. It can clean the intake pipe and backside of the intake valve thoroughly without pipes damage and corrosion different from a pollution-caused chemical intake valve cleaner.
  • Integrated Design -- Walnut sand can be sprayed and recy....
Check Stock

E1840P Sloppy Mechanics Stage 2 Camshaft LS7 Lifter 1218 Valve Spring Head Gaskets Bolts Kit for 1997-2007 LS LS1 5.3L 5.7L Engine

  • Cam and lifter kit include: 1 intake seal set, 1 timing cover gasket set, 1 valley cover gasket, 1 oil pan gasket, 2 exhaust manifold gaskets, 1 rear main seal, 1 rear main cover gasket, 2 multilayer steel cylinder head gaskets, 30 cylinder head bolts, 16 ls7 valve lifters, 16 beehive valve springs, 1 e-1840-p camshaft.
  • E1840P camshaft kit fit for 1997-2007 GM Chevy LS L92 L99 5.3L 5.7L V8 LSx Sloppy Stage 2.
  • 16pcs valve springs: outside diameter of outer spring (in): 1.290 in.
  • inside diameter of outer spring (in): 0.885 in.
  • We offer you a 12-month warranty. Any problems, just contact us through email, we ....
Check Stock