Top I2c Interface Reviews

DS3231 AT24C32 IIC RTC Module Clock Timer Memory Module Beats Replace DS1307 I2C RTC Board (Batteries not Included) + 20 PCS Male to Female Jumper Wire Cable

  • DS1307 I2C real-time clock chip (RTC) 24C32 32K I2C EEPROM memory..
  • The DS1307 is accessed via the I2C protocol..
  • Two wire I2C interface. Hour: minutes: seconds AM/PM. Day month, date - year,Accurate calendar up to year 2100..
  • 1Hz output pin.56 Bytes of non-volatile memory available to user..
  • Size: 2.8cm x 2.7cm. / 1.14inch x 1.02inch..
Check Stock

SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield Compatible with Arduino R3 Mega2560

  • Sunfounder I2C LCD 2004 displays characters of 4 rows with 20 characters in each..
  • I2C Address: 0x27 or 0x3F.Compatible with Arduino R3/2560 board. http://wiki.sunfounder.cc/index.php?title=I2C_LCD2004.
  • Professonal Support: SunFounder customer service team are always willing to solve any question from our customers .Any problem, please contact us on Amazon..
Check Stock

AITRIP 10PCS PCF8574 PCF8574T IO Expansion Board I/O Expander I2C Evaluation Develop Module

  • The PCF8574 IO Expansion Board provides general-purpose remote I O expansion via the two-wire bidirectional I2C-bus (serial clock (SCL), serial data (SDA)..
  • The main resources: PCF8574, I2C interface, the 8-bit parallel.
  • Typical applications: for I / O resource constraints the MCU I / O expansion.
  • PCF8574T expansion board applicable to a variety of platforms including AVR / ARM.
  • PCF8574T PCF8574 IO expansion board support I2C bus cascade (by pin header row seat docking methods can be used simultaneously multiple I2C modules).
Check Stock

6pcs GY-521 MPU-6050 MPU6050 Module 3 Axis Accelerometer Gyroscope Sensor Module 6 DOF MPU-6050 16Bit AD Converter Data Output IIC I2C DIY Kit for Arduino

  • 【GY-521 MPU-6050 Module】Integrates 3-axis gyroscope and 3-axis accelerator, including the hardware accelerator engine for devices connected to the second I2C port.
  • 【Built-in Chip】With three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs and another three ones for digitizing the accelerometer outputs..
  • 【Easy to use】The measured values of the sensor can be interrogated by the I2C interface. The accelerometer can be operated at both 3.3V and 5V. Suitable for Arduino and Raspberry Pi..
  • 【User-programmable Gyroscope】With a full-scale range of ±250, ±500, ±1000, and ±2000°/sec (dps) and a user-programmable accelerometer with a full-scale range of ±2g, ±4g, ±8g, and ±16g Supports the I2C serial interface and has a separate VLOGIC reference pin..
  • 【Universal Usable】The sensor can be used to develop various entertaining applications and systems. Ideal for projects with gaming and virtual reality devices, GPS navigation (for drones and RC planes) and DIY robots..
Check Stock

SparkFun MicroMod Artemis Processor - Modular Interface Ecosystem That Connects Artemis microcontroller/Processor Board to Various/Carrier Board peripherals

  • Artemis General Features: 1M Flash / 384k RAM, 48MHz / 96MHz turbo available, 6uA/MHz (operates less than 5mW at full operation), 48 GPIO - all interrupt capable, 31 PWM channels, Built in BLE radio and antenna.
  • Additional Artemis Features: 10 ADC channels with 14-bit precision with up to 2.67, million samples per second effective continuous, multi-slot sampling rate.
  • Additional Artemis Features: 2 channel differential ADC, 2 UARTs, 6 I2C buses, 6 SPI buses, 2/4/8-bit SPI bus, PDM interface, I2S Interface, Secure 'Smart Card' interface, FCC/IC/CE Certified (ID Number 2ASW8-ART3MIS).
  • Specific Peripherals made available on MicroMod Artemis: 1x USB dedicated for programming and debug, 1x UART with flow control, 2x I2C, 1x SPI, 1x Quad-SPI, 8x Fast GPIO, 2x Digital Pins, 2x Analog Pins, 2x PWM, 1x Differential ADC pair, Status LED, VIN Level ADC.
  • Additional peripherals are available but are shared on dedicated MicroMod pins. Processor board only, additional carrier board(s) will be needed to use..
Check Stock

HiLetgo 2pcs 5V 2004 1602 LCD Display IIC I2C Adapter IIC Serial Interface Adapter for Arduino Robort Parts

Check Stock

Adafruit LIS3DH Triple-Axis Accelerometer +-2g/4g/8g/16g [ADA2809]

  • Three axis sensing, 10-bit precision with �2g/�4g/�8g/�16g selectable scaling.
  • Both I2C (2 possible addresses) and SPI interface option.
  • Plus 3 additional ADC inputs you can read over I2C.
  • Tap, Double-tap, orientation & freefall detection.
Check Stock

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

  • The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
  • TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
  • The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
  • In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
  • The chip is compatible with 3V and 5V and can be used with any logic level.
Check Stock

Obstacle Avoidance Sensor TCRT5000 IR Infrared Reflective Sensor Line Detect Tracking for Arduino Robot Smart Car (Pack of 10)

  • APDS-9960 APDS9960 RGB Gesture Sensor Module.
Check Stock

HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino

  • The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
  • A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
  • On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
  • If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
  • Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
Check Stock

4Pcs INA219 I2C Bi-Directional DC Current Power Supply Sensor Breakout Board Module I2C IIC Interface

  • INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
  • INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
  • INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
  • INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
  • Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....
Check Stock

Pisugar 3 Plus Portable 5000 mAh UPS Lithium Battery Power Module Platform for Every Raspberry Pi 3B/3B+/4B Model Accessories handhold(Not Include Raspberry Pi)

  • PiSugar 3 plus adds a software watchdog function. When the function is turned on, the dog needs to be kicked regularly, which can effectively prevent the Raspberry Pi from crashing and improve the reliability of the system..
  • PiSugar 3 plus provides hardware battery protection like never before, limiting battery voltage to nearly 80%. When charging protection is turned on, the battery cycles life can be improved.Set up quadruple overvoltage protection function, overcurrent protection function and undervoltage protection function to ensure the safety of the Raspberry Pi, PiSugar as well as the lithium battery..
  • PiSugar 3 plus continues to use the pogo pin design to connect with Raspberry Pi from the back. In this way, it does not occupy the GPIO, and is compatible with other GPIO devices..
  • PiSugar 3 plus has full UPS functions and can set up multiple awakening methods to meet various unique project needs..
  • PiSugar 3 plus communicates with the Raspberry Pi through the I2C interface and is compatible with most I2C devices. In addition, the I2C communication address can be customized to avoid I2C address conflicts..
Check Stock

ACEIRMC VL6180 VL6180X Range Finder Optical Ranging Light Sensor Module Gesture Recognition Sensor I2C Interface 3.3V 5V Emitter Ambient Light Sensor for Arduino I2C (4)

  • VL6180 VL6180X Range Finder Optical Ranging Sensor Module Gesture Recognition Sensor.
  • VL6180 is a time-of-flight ranging sensor. The sensor contains a very small laser source and a matching sensor..
  • I2C interface for device control and data, two programmable GPIOs..
  • VL6180X can detect the "time of flight" or the time required for the laser to recover the sensor to calculate the distance..
  • VL6180 VL6180X Range Finder Optical Ranging Sensor Module for Arduino I2C Interface 3.3V 5V gesture recognition.
Check Stock