Top Dc Isolation Mini Power Reviews

Mixer Module, Bandwidth Mixing 0.1‑500MHz High Frequency Transducer -10dBm for Quadrature Modulation for Base Station for HF VHF Receiver

  • Single Power Supply: The mixer module is designed to be powered by a single power supply, and the RF, IF and LO ports have DC isolation capacitors for easy use.
  • 10.3dB SSB Noise Figure at 70MHz: With the output amplifier and optimal source impedance of this mixer module, the SSB noise figure is 10.3dB at 70MHz. There is no insertion loss, no external duplexer, and no passive termination.
  • Low Distortion and Wide Dynamic Range: AD831 is a low distortion, wide dynamic range, single chip mixer, very practical.
  • -10dBm LO Power Consumption: Provides +24dBm third order intercept point, can achieve -10dBm LO power consumption, without high power LO drivers, there are no corresponding shielding and isolation problems, can improve system performance and reduce costs.
  • Wide Application: Suitable for applications such as RF‑IF down conversion in HF and VHF receivers, second mixer in base stations, DC baseband conversion, quadrature modulation and demodulation, and Doppler shift detection in imaging.
Check Stock

Frequency Converter AD831 Single Chip High Frequency RF Mixer Radio Frequency Conversion Module for HF and VHF Receiver, 0.1-500MHz

  • WITH VARIOUS PORTS-- There is no corresponding shielding and isolation problems, therefore, compared with the passive mixer to improve the performance of the system, reduce the system cost. The mixer is designed as a single power supply, RF, IF and LO ports with DC isolation capacitor, easy to use..
  • POWERFUL-- The operating frequency of the RF and LO inputs can be as high as 500MHz. IF output is single ended voltage output. With 250 MHz output bandwidth. A single resistor connected between pins OUT and FB is used to set the gain..
  • EASY TO USE-- When the mixer's output amplifier and the optimum source impedance, the SSB noise figure of the mixer is 10.3dB at 70MHz. Different from the passive mixer, there is no insertion loss, no need external duplex device, and no need passive termination for AD831..
  • APPLICATION-- The AD831 is a low distortion, wide dynamic range, single chip mixer, suitable for HF and VHF Receiver RF-IF frequency, second mixer in DMR base sta....
Check Stock

Loulensy AC Voltage Transducer Voltage Sensor Transmitter Transformer Input 0-300V AC Output 0-5V DC

  • Working Stability: annual change 003c 0.2%.
  • Impulse Voltage:5KV(peak value),1.2/50uS.
  • Load Capacity: 2 times current continuous.
  • Storage Environment:-40 to +115 degress Centigrade,20%-95% without condensation.
  • Isolation Withstanding Voltage:AC 2.0KV/min*1mA between input/output/power.
  • Power Supply(defaulted):24V DC +/-15% (If 15V or 12V needed,please leave a message).
  • Feature:Voltage Terminal Insert,standard din rail(35mm)mounting or pannel mounting.
  • Working Environment:-25 to 80 degrees Centigrade,20%-90% without condensation.
  • Isolation Resistance:20M Ohm(DC500V) or above.
  • Capacity Max:0-500V AC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
Check Stock

Loulensy AC Voltage Transducer Voltage Sensor Transmitter Transformer Input 0-400V AC Output 0-5V DC

  • Working Stability: annual change 003c 0.2%.
  • Impulse Voltage:5KV(peak value),1.2/50uS.
  • Load Capacity: 2 times current continuous.
  • Storage Environment:-40 to +70 degress Centigrade,20%-95% without condensation.
  • Isolation Withstanding Voltage:AC 2.0KV/min*1mA between input/output/power.
  • Power Supply(defaulted):24V DC +/-15% (If 15V or 12V needed,please leave a message).
  • Feature:Voltage Terminal Insert,standard din rail(35mm)mounting or pannel mounting.
  • Working Environment:-10 to 50 degrees Centigrade,20%-90% without condensation.
  • Isolation Resistance:20M Ohm(DC500V) or above.
  • Capacity Max:0-500V AC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
Check Stock

High Frequency Transducer, Mixer Module 0.1‑500MHz Bandwidth Mixing for HF VHF Receiver for Quadrature Modulation for Base Station

  • -10dBm LO Power Consumption: Provides +24dBm third order intercept point, can achieve -10dBm LO power consumption, without high power LO drivers, there are no corresponding shielding and isolation problems, can improve system performance and reduce costs.
  • 10.3dB SSB Noise Figure at 70MHz: With the output amplifier and optimal source impedance of this mixer module, the SSB noise figure is 10.3dB at 70MHz. There is no insertion loss, no external duplexer, and no passive termination.
  • Single Power Supply: The mixer module is designed to be powered by a single power supply, and the RF, IF and LO ports have DC isolation capacitors for easy use.
  • Wide Application: Suitable for applications such as RF‑IF down conversion in HF and VHF receivers, second mixer in base stations, DC baseband conversion, quadrature modulation and demodulation, and Doppler shift detection in imaging.
  • Low Distortion and Wide Dynamic Range: AD831 is a low distortion, wide dynamic range, single chip mixer, very practical.
Check Stock

Loulensy AC Voltage Transducer Voltage Sensor Transmitter Transformer Input 0-150V AC Output 4-20mA DC

  • Working Stability: annual change 003c 0.2%.
  • Impulse Voltage:5KV(peak value),1.2/50uS.
  • Load Capacity: 2 times current continuous.
  • Storage Environment:-40 to +70 degress Centigrade,20%-95% without condensation.
  • Isolation Withstanding Voltage:AC 2.0KV/min*1mA between input/output/power.
  • Power Supply(defaulted):24V DC +/-15% (If 15V or 12V needed,please leave a message).
  • Feature:Voltage Terminal Insert,standard din rail(35mm)mounting or pannel mounting.
  • Working Environment:-10 to 50 degrees Centigrade,20%-90% without condensation.
  • Isolation Resistance:20M Ohm(DC500V) or above.
  • Capacity Max:0-500V AC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
Check Stock

DC 12V LED Power Supply Driver Transformer - Lustaled 15W Waterproof IP67 120VAC to 12V DC Converter Constant Voltage LED Switching Power Supply for LED Strip Lights, G4 MR11 MR16 LED Display (2-Pack)

  • [DC 12V LED Power Supply]: Mini size 15W LED driver transformer, Input: AC100-265V, Output: DC 12V.
  • [Wide Application]: Our 15W LED power supply driver is suitable for most of devices with DC12V such as CCTV, Illuminated Module Signboard, Cabinet Lights, LED Strip Lights, LED Display, LED Module, Indoor/Outdoor Deck Lights, Indoor Stair Step Lights, LED Light Bulbs like G4, MR11, MR16 LED bulbs..
  • [Good Heat Dissipation]: LED 12V transformer is made of aluminum, easy for heat dissipation and ensure stability. 100% Waterproof IP67 protect for outdoor use.
  • [Safer Design]: This DC 12V LED driver is flicker-free output, thermal overload, over current, over voltage and short circuit protection built in.
  • [Note]: Please confirm whether the input voltage (AC100-265V) can work in your place before purchase the 12V switching converter, please make sure the power is lower than or equal to the rated power supply, otherwise it may burn..
Check Stock

Senva C-2343 : Current Transducer 0-5VDC Output

  • Self-powered, no external power supply required..
  • Easy to install and use, no need to connect DC into the circuit when measuring..
  • Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output..
  • Straight- through structure design, isolation withstand voltage up to 2000V..
  • Measured current AC 0-10/20/50A, output signal DC 0-10V..
Check Stock

Miller 191941 Transducer, Current 200A Module Supply V +/- 15V

  • Straight-through structure design, isolation withstand voltage up to 2000V..
  • Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output..
  • Self-powered, no external power supply required..
  • Measured current AC 0-10/20/50A, output signal DC 0-5V..
  • Easy to install and use, no need to connect DC into the circuit when measuring..
Check Stock

DC Voltage Transducer Voltage Sensor Transmitter Transformer Input 0-150V DC Output 0-5V DC

  • Isolation Resistance:20M Ohm(DC500V) or above.
  • Capacity Max:0-1000V DC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
  • Power Supply:11-30V DC(any stable power,e.g. 15V dc).
Check Stock

Loulensy 3-Phase AC Voltage Transducer Sensor Transformer Transmitter 3-Input 0-300V AC with 3-Output 0-5V DC

  • Capacity Max:0-500V AC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
  • Impulse Voltage:5KV(peak value),1.2/50uS.
  • Default Frequency:40-60Hz(contact us,if you specially need different frequency,e.g. 100Hz).
  • Load Capacity: 2 times current continuous.
  • Isolation Withstanding Voltage:AC 2.0KV/min*1mA between input/output/power.
  • Feature:Voltage Terminal Insert,standard din rail(35mm)mounting or pannel mounting.
  • Storage Temperature:-40 to 70 degrees Centigrade,20% to 95% without condensation.
  • Working Stability: annual change 003c 0.2%.
  • Working Environment:-10 to 50 degrees Centigrade,20% to 90% without condensation.
  • Isolation Resistance:003e/=20M Ohm(DC513V).
Check Stock

AD831 High Frequency Transducer RF Mixer Module 500MHz Bandwidth Mixing Down Mixing Dual Balanced Mixer Single Chip Radio Frequency Converter -10dBm

  • The AD831 is a low distortion, wide dynamic range, single chip mixer, suitable for HF and VHF Receiver RF-IF frequency, second mixer in DMR base station, DC-baseband conversion, quadrature modulation and demodulation, and ultrasound imaging, frequency move detection and other applications.
  • The AD831 has provide +24 dBm third-order intermodulation intercept point, realization of -10 dBm LO power, without the need for a high power LO drive.
  • There is no corresponding shielding and isolation problems, therefore, compared with the passive mixer to improve the performance of the system, reduce the system cost.
  • The mixer is designed as a single power supply, RF, IF and LO ports with DC isolation capacitor, easy to use.
  • The amplifier has low DC offset characteristics, so it can be used in DC-baseband frequency conversion and quadrature amplitude demodulation.
Check Stock

DC Voltage Transducer Voltage Sensor Transmitter Transformer Input 0-100V DC Output 4-20mA DC

  • Isolation Resistance:20M Ohm(DC500V) or above.
  • Capacity Max:0-1000V DC (Customerized,contact operator if you need other input ranges,e.g.0-75mV or 0-300V).
  • Power Supply:11-30V DC(any stable power,e.g. 15V dc).
Check Stock