Top Clutch Bearing clutch Reviews

Four Seasons (47654) A/C Clutch Assembly

Feature: The three main parts of the compressor clutch assembly are the coil magnet, the pulley, and the clutch plate. The clutch drive plate is splined to the input shaft of the compressor..
Package Included: 1 x Pulley With Bearing.
(Professional Installer is Highly Recommended ).
Pulley Assembly Width:10.4cm,Height:2.8cm.
Part#: 140162C,7511699,10759C,F09OGBC003,5511699,6511699.

OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
Rugged construction will easily support the weight of heavy clutch discs.
To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
2 inch O.D. shaft, 1-1/4 inch pilot, 10 splines, splines are 7.3 inches long.

【APPLICATION】B A/C Compressor Clutch Remover Installer Puller Tool Kit, is used to remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors and fit for GM, fit for Ford, fit for Chrysler, imports, and others.
【EASY TO USE】Keep all threads clean and well-oiled.
Outer part of tool has smooth side and threaded side (threads used to attach to inner clutch shaft when removing).
Start with one bearing between tool and clutch, and thread down fully onto compressor's inner shaft threads.
【HIGH-QUALITY】A/C Compressor Clutch Remover is made of stainless steel with a black coated finish, durable and long lasting.
Resists rust and corrosion under proper care and lubrication.
【PACKAGE INCLUDED】This kit includes puller body, jaw and sleeve assembly, jack-screw, thrust washer, button, bearing, and puller plates.
【CARRYING CASE】Comes with a carrying plastic carrying case for easy organization, storage, and transport.

The ROP Shop replacement PTO Clutch CCW for Husqvarna 179335, 414737, 532179335, 532414737 Lawn Mower.
Specs - Crankshaft: 1 1/8". Pulley Outside Diameter: 6 1/8". Direction: Counter Clockwise (CCW). Belt: 1/2" or 5/8". Refer to images 2 & 3 for more information.
Includes - (1) PTO Clutch & (1) Installation Manual.
Features - Heavy Duty "FatBoy Series" Upgrade. High Torque Cool Coil Upgrade. Integrated Water Tight Wire Harness. Replaceable Pulley Bearing. Super Smooth "Xtreme Precision" Machined Pulley.
To prevent premature clutch failure, follow the instructions included with the clutch.

Premium Quality Reman A/C Compressor Clutch..
This A/C Compressor Clutch Includes: Bearing, Hub, Pulley, and Coil which is tested for the correct resistance and voltage..
Guaranteed fit! Confirm that this A/C Compressor Clutch will fit your vehicle by using Amazon's garage..

Premium Quality Remanufactured A/C Compressor Clutch..
This Remanufactured A/C Compressor Clutch Includes: Bearing, Hub, Pulley, and Coil which is tested for the correct resistance and voltage..
Guaranteed fit! Confirm that this A/C Compressor Clutch will fit your vehicle by using Amazon's garage..

Assembly Comes with 2000RPM Clutch Springs.
ID of bearing in clutch shoe assy: 12mm (6901RS).
Please Note: The exact performance of upgrade parts will be affected by many other factor.

Valeo Premium Clutch Kits are engineered using only the highest quality components and latest technology for exceptional operation and reliability.
Premium Friction Material for Increased Durability: Valeo friction material is known as the best in the world, providing better heat dissipation and....
Consistent Comfort: Enhanced damper technology for improved filtration of noise, vibration and harshness maintaining the comfort of the original....
This kit includes a clutch cover (pressure plate), clutch disc and release bearing.

Brand New Southwest Speed and Ram Clutch Aluminum Bellhousing and 11" Clutch Kit for use with Manual Transmissions. The kit includes a replica GM 3899621 Bellhousing, Flywheel Inspection Cover, Clutch Fork with Ball Retaining Spring, Throwout Bearing, Clutch Fork Boot, Clutch Fork Pivot, Flywheel, Clutch Disc, Pressure Plate, and hardware (Part # 650-39755, 901180) > Fits transmissions with 1 5/32"-26 spline input shafts and Chevy engines with a 2 piece rear main seal.
The Southwest Speed 11" Performance Cast Aluminum Bellhousing is a reproduction of the original 3899621 bellhousing used on GM models with Big Block and Small Block engines > This performance aluminum bellhousing does not have the GM Part # 3899621 casting number but will look, fit, and perform just like original > If you are doing a restoration of an early muscle car, or just want the correct bellhousing to finish that rod project, this bellhousing is the perfect part.
Fits: > 1964-1988 Chevy Chevelle, Malibu, Monte Carlo* > 1959-1987 Chevy El Camino* > 1959-1988 Chevy Impala, Caprice, Bel Air, Biscayne, Brookwood, Kingswood, Nomad, Sedan Delivery* > 1963-1981 Chev....

Premium Quality New A/C Compressor Clutch Bearing..
Guaranteed fit! Confirm that this A/C Compressor Clutch Bearing will fit your vehicle by using Amazon's garage..

Specs: Clutch Kit, Type: Single, Disc Outside Diameter: 10", Spline Count: 15, Includes: Pressure plate, disc, release bearing, pilot bearing and....
Compatible with/Replacement for Ford/New Holland: NDA7550B, NDA7563A.
Compatible With / Replacement For: Ford/New Holland 1801 Indust/Const.
100% New aftermarket Clutch Kit built to meet OEM specifications for Ford/New Holland.

SAE shaft and bushings to fit 8 SAE pilot bearing sizes..
Plated aligning cone with graduated 1" and 1 1/8" diameters for "automatic" fit to most clutch plates..
W1158P shaft & bushings to fit 10 metric pilot bearing sizes. Tapered cone for all others..
Sizes SAE: .590, .612, .624, .668, .749, .786, .808 & .904".
Plated aligning cone with graduated diameters for "automatic" fit to most clutch plates..

For STIHL MS210 MS230 MS250 021 023 025 Chainsaw.
Replace For OEM# 1123 640 2074 / 1123 160 2050.
Package Includes: 1 x Clutch Assembly, 1 x .325"-7T Clutch Drum, 1 x Clutch Needle Bearing.