Top Chamfer Gauge Reviews

Starrett 683-4Z Inch Reading Internal Chamfer Gauge, 0-90 Degree Angle, 1-2\ Range

  • All ground surfaces are of hardened tool steel.
  • Internal gauges will measure the largest diameter of any chamfer that has an included angle within the range of angles printed on the dial face of the gauge.
Check Stock

Starrett 683-2Z Inch Reading Internal Chamfer Gauge, 0-90 Degree Angle, 0-1/2\ Range

  • All ground surfaces are of hardened tool steel.
  • Internal gauges will measure the largest diameter of any chamfer that has an included angle within the range of angles printed on the dial face of the gauge.
Check Stock

Starrett 684-1Z Inch Reading Internal Chamfer Gauge, 90-127 Degree Angle, 0-3/8\ Range

  • All ground surfaces are of hardened tool steel.
  • Internal gauges will measure the largest diameter of any chamfer that has an included angle within the range of angles printed on the dial face of the gauge.
Check Stock

ARES 48001 – External Rotary Deburring & Chamfer Tool (13-36mm) – 3/8-Inch Shank for Use with Drill or Hex Driver - Clean and Repair Threaded Fasteners, Studs, and Bolts

  • 【Deburring Chamfer Tool】EZARC Deburring chamfer tool set includes debur tools covering external diameters of 1/8″-3/4″ (3-19mm) and internal diameters of 1/8″-5/8″ (3-16mm). Deburring chamfer tool set features quick release shank fits all handheld and stationary drills..
  • 【Exquisite Crafts】The internal countersink chamfer is made of M2 high-speed steel, and the surface is black nitrided after heat treatment. The head of the external deburring chamfer is cast with zinc alloy, and the surface is black and bright electrophoretic treatment. 3 pieces of YG8 carbide blades provide better performance and longevity than high speed steel blades..
  • 【Easy to work】Attaching the deburring external chamfer tool to the end of your power drill, Use the speed on the drill bit between 0-400 RPM, and then slightly applying pressure to remove the burr. Do not use impact mode..
  • 【Safety Design】The accurate deburring external chamfer tool easily shaves the outer rough edge of bolts, newly-cut pipes or rods, removing burrs to keep edges smooth. Quickly repairs damaged bolts and tightens the nuts in place without hurting your hand, no sparks, and no burns.
  • Simplifies the repair process. The internal deburring tool with 5 flute bit design allows it drilling....
Check Stock

TAJIMA Drywall Chamfer - 180mm Sheetrock Trimming Tool with Adjustable 30 Degree Chamfer & Die-Cast Aluminum Base - TBK180-V30

  • 30 DEGREE CHAMFER TOOL - Fluorinated coating applied to aluminum base glides smoothly over materiel producing a flawless chamfered edge on drywall and....
  • SLIP RESISTANT ELASTOMER GRIP - Tajima's chamfer tool features an integrated, slip-resistant grip enhancing usability and safety.
  • DIE-CAST ALUMINUM BASE - Designed with a lightweight yet durable aluminum chassis, this Tajima tool will withstand the rigors of daily professional....
  • ADJUSTABLE CHAMFER - Tajima's chamfer tool features and adjustable chamfer edge ranging from 1mm - 4mm for flexibility on the job..
  • SUPERIOR JAPANESE CONSTRUCTION - Built with durability and quality in mind, Tajima's chamfer tools offer both thoughtful form and functionality that....
Check Stock

B Blesiya Stainless Steel Chamfer Gauge Gage Chamfering Inspection Tool Square Ruler

  • Special printing ensures that the scales and numbers are clear and not easy to wear.
  • Stainless steel gauge body ensure durability, it is not easy to bend.
  • Chamfer gage can be used metric reading and graduation is 0.5mm.
  • To measure internal and external chamfers.
Check Stock

Chamfer Gauges,Chamfering Ruler,Stainless Steel Caliper 0-50mm,Mechanical Reading,for Mechanical Manufacturing, Glass Processing,etc

  • 2.Used in mechanical manufacturing, glass processing and other fields..
  • 3.The measurement result is accurate and the error is about ±0.02mm..
  • 4.Accuracy assurance, solid workmanship. Laser calibration, not easy to rust..
  • 5.This gauge is made of high quality stainless steel, durable and rust-resistant..
Check Stock

Arrows Before Bullets (8-Bit)

  • Chamfer Tool - keep your casings smooth and precise with the Hornady Case Prep Center 6-Blade Inside Diameter Chamfer Tool 050172. Designed to remove the burrs from the inside of a case mouth for consistent seating depth and reduces the chance of shaving material off when a bullet is seated.
  • Easy to Use Chamfering Tool Bit - after your cases are cleaned or if you are using new brass you will want to chamfer your cases for a clean smooth cut. This tool is threaded 8-32 so it will work in the Hornady Lock-N-Load Case Prep Trio, Case Prep Center or installed in the Universal Accessory Handle.
  • High Precision & Tough Durability - great chamfer tool bit for reloaders to help keep chamfers and deburrs square with the case mouth, eliminating slippage and reducing errors. Universal design works on all cases 17-45 cal.
  • Remove the Burrs Inside - when there are sharp edges on your brass after trimming, you need to cut them down with this brass chamfer tool. This tool easily removes burs from the case mouth allowing you to seat the bullet without having to worry about the bullet being damaged.
  • Hornady Case Prep Center - with many different options for case prep reloading, Hornady has an option for you. Find the right reloading tools and accessories to compl....
Check Stock

Flex-Hone Tool CHC5818 Brush Research CH-C Large Chamfer Flex-Hone, Silicon Carbide, 5/8\ Diameter, 180 Grit (Pack of 1)

  • The Flex-Hone for Chamfer Blending has the ability to blend and radius sharp edges and remove microburrs on chamfered holes eliminating stress risers caused by the chamfering operation.
  • Designed to polish and radius the outer corners (the intersection of the chamfer and flange face) as well as the inner corners and hole.
  • Polished and radiused chamfer surfaces have been shown to be very beneficial on critical rotating parts.
  • Suitable for finishing titanium, inconel, super CVM and nickel based stainless steel alloys.
Check Stock

Hakko-CHP-170 Micro Cutter - Red & Irwin Vise-Grip Wire Stripping Tool/Wire Cutter, 8-Inch (2078309)

  • Chamfer-cut medium blunt nipper has 8mm long jaw with angled head for flush-cutting applications on up to 14 gauge (1.6mm) copper and soft wire.
  • 21-degree angled cutting surface eases access to board for cutting soft wire in component-dense areas.
  • HRC 58-rated 3.0mm heat-treated carbon steel construction provides durability and long life.
  • Precision-ground holes and surfaces provide smooth movement, and spring returns tool to open position to reduce operator fatigue.
  • Dolphin-style nonslip hand grips with curved fore-edge provide comfort and control, and Parkerized surfaces prevent glare and increase corrosion resistance.
Check Stock

2 Pack Oregon 90PX055G Low Profile 3/8-Inch Pitch 0.043-Inch Gauge 55-Drive Link Saw Chain for Stihl 61PMMC3 55 16 Bar

  • 2 Pack, Oregon 90PX055G Low Profile 3/8-Inch Pitch 0.043-Inch.
  • Low-vibration chamfer chisel cutters have an angular shape with twin cutting corners for excellent performance and edge-holding durability.
  • Recommended Bar Lengths: Up to 16in. (40cm) Recommended Saw Sizes: Up to 42cc.
  • Always install 90PX chains on a .043" gauge Double Guard bar (MLE part numbers) to obtain all the advantages of the Micro-Lite system.
Check Stock

XSPC Easy Cut & Bend Toolkit for XSPC PETG Tubing

  • Heavy Duty Hose Cutter – The heavy duty cutter can cut through PETG tubing as effortlessly as you would cut flexible PVC tubing. Easily cut PETG rigid tubing without the need for a saw..
  • PETG Easy Bending Tool – This tool allows you to easily bend PETG tubing at an angle between 0 and 180 degrees. Just heat the tubing with the bending rubber inserted, insert the tube into the tool and bend it to the required radius. This simple tool takes the guess work and difficulty out of bending rigid tube. (Suitable for 12-14mm outer diameter tubing).
  • Bending Rubber – Solid rubber extrusion for bending PETG tubing. Insert into the tube before bending, to stop the PETG tube kinking, or deforming. (Bending rubber diameter is 10mm).
  • PETG Chamfer Tool – Quickly chamfer the edges of PETG tubing by using this handy tool. Just insert the tubing and turn anticlockwise..
  • PETG Edging Sandpaper – Ideal for sanding the edges of PETG tubing, after using a chamfer tool..
Check Stock

JIUNENG 2-in-1 Pneumatic Chamfer Tool,Mini Pneumatic Chamfering Machine Set,Portable Handheld Metal Edge Beveler with Replace Blades for Metal Deburring,45 Degree Arc

  • 【Easy Operation】: This 45-degree mini chamfering machine air tools has a new lightweight design, Two right-angle cutter heads and bearings have been installed on the machine, and two R-angle cutter heads are also equipped.Use the matching wrench to easily adjust the chamfer size and replace the blade.Can be easily operated with one hand..
  • 【Stable Speed】: This portable trimming chamfering tool can withstand high impact and high speed. The speed is increased and the chamfer is smoother with US 1/4 inch metal filter, free speed: 30000 RPM, air consumption 0.4/min..
  • 【Durable】: Pneumatic chamfering tool with 1-5 air intake adjustment, freely adjust the gear speed you need. The safety switch is used to prevent accidental touch to protect the user's safety at all times. Use the matching wrench to easily adjust the chamfer size and replace the blade.Can be easily operated with one hand..
  • 【Higher Efficiency】: The upgraded version of the metal beveling grinder, the new design adopts a new chrome-plated all-aluminum shell with high-quality bearings and blades for smoother deburring and chamfering..
  • 【Application】:JIUNENG's air beveler tool adopts the thinnest nut lock bearing at present, which can chamfer in the narrowest and shallowest space, an....
Check Stock