Top 6 Layers Pcb Reviews

PHOPOLLO 5050 LED Strip Lights, 50ft LED Lights for Bedroom with 44 Key IR Remote Controller and 12V Power Supply

  • Consists of 20 static colors, 8 dynamic modes and 6 DIY colors.
  • Consists of individual 5050 LED emitters on 2 rolls of 25ft led strips.
  • Double side sticky adhesive allows for quick and easy installation in a wide variety of locations.
  • Safe to touch under 12 volt working voltage.
  • double copper layers on pcb board makes the lights stronger.
Check Stock

Ultra-Small RPi GPIO Terminal Block Breakout Board Module, for Raspberry Pi

  • The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W..
  • Terminal block pitch 2.54mm/0.1", wire size range 28AWG to 18AWG, strip length 4.5mm, screw M1.6 steel, pin header and cage copper..
  • FR-4 fiber glass PCB, dual copper layers..
  • 2x20 positions header connect to Raspberry Pi board..
  • Packing list: 1x terminal block breakout module, 4x M2.5x6mm screws, 4x 10mm nylon standoffs. 2x 11.5mm brass standoffs, 1x small slotted screwdriver (NOTE: the item not include Raspberry Pi Board)..
Check Stock

zgs78hh 18V Battery Chip Protect Board Replacement Battery Protection, Circuit Board for Makita BL1830 BL1850

  • 【Dimension】 -Size：200mmx150mm/7.87"x5.91"(L*W).
  • 【Material】 -The copper clad laminate is made of FR-4 glass fiber and copper, the number of layers issingle-sided.
  • 【Features】- The copper clad board is resistant to high temperature, is not easily oxidized, is not easily deformed, and is convenient for welding.
  • 【Application】 - PCB circuit boards are very suitable for making PCB circuit boards and models. It is widely used in product development, DIY experiment, maintenance, production, etc.
  • 【Noted】 -The product may be slightly scratched or dirty during transportation, which will not affect its use.
Check Stock

ARCELI Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA 2560 R3 DIY Soldered

  • PCB: FR-4 fiber glass PCB, dual copper layers, size 120mm x 78mm. Pads grid / pitch 2.54mm / 0.1", hole diameter 0.8mm. Terminal block pitch 3.5mm / 0.138", hole diameter 1.2mm..
  • Terminal Block: Pitch 3.5mm / 0.138" mini terminal blocks, total 84 pins(3pole x24pcs, 2pole x6pcs ). Wire range 26~16AWG, strip length 5mm, screws M2 steel, pin header and cage brass..
  • Female Header Socket: Pitch 0.1"/2.54mm, pin length 15mm / 0.59" Single row 10pin x1pcs, singal row 8pin x 5pcs, dual row 18pin x1pcs..
  • Note: This is not original Arduino product.it only a substitute accessories from ARCELI.
Check Stock

Miuzei PCB Board Prototype Kit for Electronic Projects Circuit Solder Double-Side Board with 40 Pin 2.54 mm Male to Female Headers Connector 2P&3P Screw Terminal Block Solder Flux Solder Wire

  • ⭐【6 Different Sizes PCB Boards】Double Sided Prototype PCB Boards--1 × 9*7cm, 2 × 8*6cm, 5 × 8*2cm and 5× 7*5cm, 5 × 7*3cm, 5 × 5*4cm PCB....
  • ⭐【Convenient for Projects】The upgrate 0.8mm....
  • ⭐【Header Connector】6 pcs 40 pin Male Header, 4 pcs 40 pin Pitch Right Angle Male Headers, 6 pcs 40 Pin Female Header.
  • ⭐【Screw Terminal Block】8 Pcs Screw Terminal Block: 6 pcs 5.08-301-2P and 6 pcs 5.08-301-3P.
  • Pitch: 5.08mm, Rated Voltage: 300V, Rated Current:....
  • ⭐【High Quality & Warranty】Durable Glass Fiber-FR4 Material (Thickness 1.6mm) is A Very Solid and Durable Prototype Circuit Board.
Check Stock

YMDK GK61x GK61xs GK64x GK64xs Anodized Aluminum CNC Case (Only Aluminum Case)

  • Package Included: CNC Case + Rubber Feet + Screws.
  • New GK61x GK61xs GK64x GK64xs plate and PCB can install in directly..
  • Old GK61 GK64 plate can't use since the size is bigger than normal 60 case.You can just replace a GH60 size customized plate is ok.The plate need to be compatible with GK61 PCB..
  • How to judge old and new edition: Old GK61 GK64 PCB is white and only support single 6.25u space New GK61x GK61xs GK64x GK64xs PCB is black and can support split space and single space at the same time..
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.If little keys not working,check the switch pin whether it's bent at first.Especially Kailh switches.
Check Stock

Xtrfy K5 Compact RGB Transparent White, US Layout

  • Super-scan technology for instant response.
Check Stock

Polychem Ultra CR Ultrasonic Cleaning Solution 1 Gallon

  • Corrosion remover, mildly acidic. Rinse residue free.
  • Parts to be cleaned: non-ferrous and light metals, pcb's with water damage, glass, plastics, tarnished brass and chopper, scuba diving gear.
  • Contaminants to remove: corrosion, lime deposits, water damage, oxide layers, rust, grease, oil. Brightens brass and chopper alloys.
  • Dilute with water to 1-5 percent before use.
Check Stock

The Warhol Incident (Alexis Parker Book 2)

  • Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.
  • Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some keys not working after plugging,please check whether your switch pin is bent or not.Make sure plug in 90 degree above plate.
  • This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to replace a non -replacable GH60 size plate is ok..
  • PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.
Check Stock

Gateron V2 Clear Stabilizers PCB Mount Screw in Stabilizer Customized Distance No Dropping Wire for Mx Mechanical Keyboard PCB (Gateron Stab V2 Clear 1+4)

  • This is Gateron PCB Mount Screw In Crystal Stabilizer，.
  • Package Included：1x6.25u +1x7u +4x2u PCB Mount Screw-in Stabilizers + pad + Screws For 60% 68 75 84 87 Keyboard.
  • The plastic inserts and boat only has 10 pcs each. There is extra wire presented, but no plastic insert boat presented.
  • If your keyboard is 96 or 104 108 layout,need to buy 2 set.
  • This stabilizers are PCB screw-in stabilizers which is directly mounted on PCB.V2 stabilizers is designed to prevent the wire from dropping off.It's more stable than old edition..
Check Stock

GK64 GK64x RGB Hot Swap Programmable Wired Case PCB Plate Cherry MX Keyboard DIY kit Replacable Space

  • Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.This is DIY kit,after you....
  • Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some....
  • This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to....
  • PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
  • There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering....
Check Stock

DollaTek StepStick 4-Layer DRV8825 Stepper Motor Driver Module for 3D Printer Reprap RP A4988

  • Simple step and direction control interface.
  • It can directly interface with 3.3V and 5V systems.
  • Thermal shutdown overtemperature, shutdown overcurrent, and under-voltage lockout.
  • 4 layers, 2 oz copper PCB for better heat dissipation.
Check Stock

MECCANIXITY PCB Board Double Sided Printed Circuit Prototyping Boards Plated Through Holes for DIY Soldering Electronic Projects, 80mmx120mm, Green Pack of 4

  • These PCB boards are great for assembly of a point to point style electronics board. Suitable for countless small electronics projects such as building a robot. If you are working with hobby electronics and want a more permanent circuit solution but don't want to design your own PCB, these are great for you!.
  • The prototyping boards we provide here are in the size of: Dimension: 80mm x 120mm / 3.15 x 4.72 inch (W*L).
  • They are made of FR-4 glass fiber, double sided with tinned through holes. This is a fast easy way to build small projects, the boards are durable and the tinned holes can take heat without lifting off..
  • Easy to cut with a rotary tool. The pre-drilled holes in each corner are great for building with two layers..
  • Please read the measurements before ordering if you are concerned about the size..
Check Stock