Top Torque Amplifier Reviews

Songhe MG90S Mini Micro 9G Servo Metal Geared Micro Servo Motor for RC Helicopter Plane Boat Car 5pcs

  • For Stall Torque: 2.2kg/cm(6V),and amplifier type: Analog controller.
  • Operating Speed for working: 0.1sec/60 degree(4.8V)~0.08sec/60 degree(6.0V).
  • Operating Voltage : 4.8V~6.0V,The starting current of the motor should be over than 1A.
  • Use on: remote control helicopters, micro robot, robot arm and boats.
Check Stock

NuNuNaNa - HBX 12891 1/12 5-Wire Steel Ring Servo Plastic Gear 12030 RC Car Part

  • SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kinds of R/C Toys and also make electronics DIY compatible with Arduino, Raspberry Pi.
  • Interface Type: Compatible with JR & FUTABA interface. Running Speed (at no load): 0.09 ± 0.01 sec/60°(4.8V ) 0.08 ± 0.01 sec/60°(6V). Maximum angle: 120°.
  • Stall Torque (4.8V): 17.5oz /in (1kg/cm). Dead band setting: 7 microseconds.
  • Amplifier Type: Analog controller. Operating Voltage: 4.8V~6.0V.
  • Please Note: The starting current of the motor should be greater than 1A. Comes with 1 year warranty and lifetime technical Support.
Check Stock

ENOMAKER Direct Drive Extruder Ender 5 Conversion Kit, Upgrade Near-end Extrusion Great at Printing TPU for Creality Ender 5, Ender 5 Pro 3D Printers

  • Direct drive, high-torque motor turntable mechanism plays 2 speeds - 33 1/3 and 45 RPM records.
  • Fully manual operation with start / stop control.
  • Balanced S-Shaped tone arm with hydraulic lift control, anti-skate, height adjustment, and lockable rest.
  • Turntable includes built-in switchable phono pre-amplifier with detachable RCA output cables.
  • Damped die-cast aluminum platter with felt slip mat.
Check Stock

Miuzei 5 Pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm/Hand/Walking Helicopter Car Boat Control with Cable, Mini Small Servos for Arduino Project

  • Application Fields: remote control helicopters, micro robot, robot arm and boats. ALL kind of R/C Toys and Arduino experiments.
  • Interface Type: compatible with JR & Futaba interface..
  • No Load Running Speed: 0.09±0.01 sec/60° at 4.8V Rotary Angle: 120°.
  • Stall Torque (4.8V): 17.5oz /in (1kg/cm).Dead band width: 7usec.
  • Amplifier type:Analog controller Operating voltage: 4.8V~6.0V.
Check Stock

ALMOCN 8PCS SG90 9G Micro Servo Motor Kit Mini for RC Robot Arm Helicopter Airplane Car Boat Controls Project

  • Application Fields: remote control helicopters, micro robot, robot arm and boats. ALL kind of R/C Toys and Arduino project..
  • Stall Torque (4.8V): 17.5oz /in (1kg/cm).
  • Interface Type: Compatible with JR & FUTABA interface. Running Speed (at no load): 0.09 ± 0.01 sec/60°(4.8V ) 0.08 ± 0.01 sec/60°(6V). Maximum....
  • Amplifier Type: Analog controller. Operating Voltage: 4.8V~6.0V.
  • NOTE: The Starting Current of The Analog Servo Motor Should Be Over 1A and Miuzei Servo SG90 are Analog Servos Need to Continuously Provide a PMW....
Check Stock

Hosyond 10 Pack Servo Motors SG90 9G Micro Servo for RC Robot Helicopter Airplane Boat Remote Control Toys, Servo for Arduino Project, Blue

  • [Applications] SG90 9G servo motor, compatible with RC helicopters, micro robots, robot arm and ships etc. Support various remote control toys and Arduino project.
  • [Interface type] This SG90 servo is compatible with JR & Futaba interface.
  • [Operating speed] 0.12 second/ 60degree ( 4.8V no load), 0.1 second / 60degree ( 6.0V no load), Max rotation angle:180 degrees.
  • [Reminder] The starting current of the analog servo motor must be greater than 1A. SG90 Servo is an analog servo and needs to continuously provide PMW signal to work normally.
Check Stock

California JOS10 Pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm,Hand,Walking Helicopter Airplane Car Boat Control, Micro Servos Arduino Project (with 20CM Dupont M-F Cable)

  • ✅SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kind of R/C Toys and also make electronics DIY based on Arduino ,Raspberry Pi.
  • ✅Stall Torque (4.8V): 17.5oz /in (1kg/cm) Dead band width: 7usec.
  • ✅Interface Type: Compatible with JR & FUTABA interface. Running Speed (at no load): 0.09 ± 0.01 sec/60°(4.8V ) 0.08 ± 0.01 sec/60°(6V). Maximum angle: 120°.
  • ✅Amplifier type:Analog controller Operating voltage: 4.8V~6.0V.
Check Stock

AmpPro Ultra Low Noise TV Antenna and Distribution Amplifier,G25F101U

  • Ultra Low Noise Amplifier Boost enhances any non-amplified antenna, delivering more range and channels. The Boost Digital TV Antenna Amplifier is the most advanced digital TV antenna amplifier available featuring very low noise figure. Using the latest advances in amplifier technology, Boost enhances any non-amplified antenna, delivering more range and available channels. Give your antenna a Boost today and get more channels and a better picture from over-the-air HD television broadcasts..
  • Works with Any Non-Amplified/Passive TV Antenna The Boost amplifier helps pick up channels that your non-amplified antenna alone may not be able to pick up. Additionally, the amplifier minimizes pixelization and drop-outs, using Clear Circuit Technology. The Boost amplifier works with any passive/non-amplified antenna. It works with VHF, UHF and Cable signals–typical gain is 25 dB for VHF, UHF and Cable..
  • Distribution Amplifier – Deliver a Better Signal to Multiple TVs The Boost amplifier can even be used to help distribute a stronger signal to multiple TVs. Connect the coax running from the antenna to the “IN /ANT” port of the amplifier, and connect the cable running from the “OUT/TV” port of the amplifier to a splitter. Then, use the provided USB c....
Check Stock

Spanners

  • Click-Torque B2 Torque wrench Drive 20-100 Nm.
Check Stock

ARES 43007 - 3/8-Inch Drive Flex Head Electronic Digital Torque and Torque Angle Wrench - 10-100 ft/lbs (13.5-135Nm) - Reversible Sealed Head - Multi-Alert Prevents Over-Torquing

  • SPECIFICATIONS: The ARES 3/8-Inch Drive Flex Head Electronic Digital Torque and Torque Angle Wrench measures within 10-100 ft/lbs (13.5-135Nm) with an accuracy tolerance of ±2% clockwise and measures torque angle with 3 separate modes: Peak Torque, Torque Angle and Peak Torque Angle. The easy-to-use digital LCD interface lets you adjust your specified torque with the push of a button and switch between five units of measurement: Nm, ft/lbs, in/lbs, kgf/m, and kgf/cm..
  • DESIGN: This digital torque wrench features a multi-alert system to help ensure you do not ever over-torque a bolt. When your specified torque is reached, the proprietary ergonomic comfort grip handle will vibrate, a audible buzzer will sound, and the LCD display back light will flash and then light up a solid red color to let you know it’s time to release. Each torque wrench also offers ten presets, so you can save and select your most frequently used torque and angle settings..
  • FLEXIBILITY: Each electronic digital torque wrench features a flex head ratchet design with peak torque, torque angle, and peak torque angle modes, so you can get exactly the right torque in exactly the right position. The “Peak Torque Angle” mode measures specified torque and immediately measures tor....
Check Stock

Seismic Audio Speakers Epicenter 5004 4 Channel Power Amplifier, 2000 Watts RMS Amplifier

  • Power Amplifier: Our Epicenter Amplifier is a beast! This is a 4 channel amplifier capable of pushing just about anything..
  • Audio Amplifier: This is a high end amplifier that is rack mountable. This power amplifier is easily capable of pushing eight 18" subwoofer cabinets or two pairs of dual 15" speakers..
  • 2000 Watts RMS Amp: This audio amplifier can handle 4 x 500 Watts RMS at 8 Ohms, 4 x 850 Watts RMS at 4 Ohms, 2 x 1600 Watts RMS at 8 Ohm Bridge of power..
  • 4 Channel Amplifier: The front of the Seismic Audio Speakers’ amplifier has channel A, B, C, and D volume controls, power indicator, clip indicator, protection mode indicator, and signal indicator..
  • Size And Weight Details: This 2000 Watts RMS amp fits standard 19” rack cases and weighs 69 lbs..
Check Stock

Wera - 5075611001 "Click-Torque B 2 torque wrench with reversible ratchet, 3/8"" x 20-100 Nm", black/green

  • Click-Torque B2 Torque wrench Drive 20-100 Nm.
Check Stock

Elac ARF-51-GE Navis Premium Powered Floorstanding Tower Speaker - (Each) Gloss Ebony Emara

  • Speaker Type: 3-Way Powered - Tweeter: 1" Soft Dome Concentrically Mounted - Midrange: 4" Aluminum - Woofer: 3 x 5-1/4" Aluminum.
  • Frequency Response: 43Hz - 28kHz - Crossover Frequency: 2.2kHz / 260Hz - Total Amplifier Power: 300 Watts Total.
  • Bass Amplifier: 160 Watt Bash Amplifier - Midrange Amplifier: 100 Watt Bash Amplifier - Tweeter Amplifier: 40 Watt Class AB Amplifier.
  • Height: 40.35" - Width: 7.44" - Depth: 9.45" - Weight: 46.30 lbs.
  • SINGLE SPEAKER - SOLD INDIVIDUALLY - PURCHASE TWO FOR A PAIR.
Check Stock