Top Time Delay Switch Reviews

UCTRONICS DC 12V Time Delay Relay Module for Smart Home, Tachograph, GPS, PLC Control, Industrial Control, Electronic Experiment, Arduino Robot

Max. Load Voltage: terminal NC is DC 30V or AC 250V, terminal NO is DC 28V or AC 125V.
Functions: Supports on delay and off delay modes, the delay time can be adjusted from 0.1s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer..
Self Protection: Built with protection against reversal diode, supports anti-reverse protection. NOTE: Please remove the jumper cap of S5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly..
Applications: This module works as a switch with time delay on and off function, highly recommended for automotive circuit modification, and LED lights, DC motors, pump and smart home control system..

Check Stock

UCTRONICS DC 12V Time Delay Relay Module with Plastic Enclosure, On Delay and Off Delay for Automobile, Raspberry Pi, Industrial Control, and Other Electronic Projects

Max. Load Voltage: terminal NC is DC 30V or AC 250V, terminal NO is DC 28V or AC 125V.
Functions: Supports on delay and off delay modes, the delay time can be adjusted from 0.1s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer..
Self Protection: Built with protection against reversal diode, supports anti-reverse protection. NOTE: Please remove the jumper cap of S5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly..
Applications: This module works as a switch with time delay on and off function, highly recommended for automotive circuit modification, and LED lights, DC motors, pump and smart home control system..
You'll Be Getting: A time delay relay module U6031, 2 pieces of protective case and 2 mounting screws.
the plastics case keep the module free from dust and water, which is available for more applications than the separate module..

Check Stock

Donner Compressor Pedal, Donner Guitar Delay Pedal

【Advanced Compressor Pedal】Donner’s comprehensive pedal can smoothen out dynamics between the high and low frequencies without degrading the original sound, offering you a more even and robust sound..
【Versatile Functions】Our Ultimate Comp features an easy-to-use tone control: COMP (compression intensity), TONE (brightness) and LEVEL (output volume) for different uses. These dedicated controls provide you a superb sound shaping..
【Two Practical Modes】The guitar compressor pedal also offers a mode selector switch of NORMAL and TREBLE. Signal can be transmitted in two modes to satisfy various needs of your playing..
[Analog Delay Pedal] Reproduces the warm and natural classic vintage analog delay sound..
[Flexible Delay Pedal] 20ms to 620ms of delay time. Adjustable delay level and feedback..

Check Stock

EarthQuaker Devices Avalanche Run V2 Stereo Reverb & Delay with Tap Tempo Guitar Effects Pedal

New custom-built enclosure, Flexi-Switch silent relay based switching for traditional latching or momentary operation, and updated reverb algorithm....
A dreamy sonic discovery device with up to 2 seconds of delay time and a lush reverb..
Features complete control over delay time, repeats, mix and voice (with the tone control), as well as control over the reverb length and mix.
It can run in one of 3 different modes to really play with your tone: Normal, Reverse and Swell.
Features an expression jack that can be assigned to one of six different controls using the 'EXP' selector switch.

Check Stock

ENERLITES PIR Motion Occupancy Vacancy Motion Sensor Light Switch, 500W, 5A, Motion Sensor Night Light, Single-Pole, Smart LED Backlight, Neutral Not Required, Ground Required, HMOS-J-W, White

Motion detector light switch replaces standard switch, automatically turns connected load ON / OFF based on motion detected.
Smart LED backlight will turn on when motion is detected for easy location in the dark in vacancy mode.
Occupancy switch mode (Auto ON, Auto OFF) and vacancy switch mode (Manual ON, Auto OFF) allow you to customize the sensor according to your needs.
Time delay options: 15 sec (Test), 15 min, 30 min. Motion sensor will turn off after the delay time is up. Single pole use only. Not for three-way wiring.
Neutral wire not required, ground wire required for installation. 120-277VAC, CFL/LED: 150W, incandescent/halogen: 500W, motor: 1/8HP. Motion sensor wall switch ranges 180 Degree, 700 sq. ft. coverage. Operating temperature (32 – 131°F). UL listed.

Check Stock

Sensky BS010WL DC 12v to 30v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting, Light Sensor, time and Distance Adjustable (with Light Sensor)

【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting..
【Light Sensor Adjustable】: This function allows you to use the motion sensor in different ambient condition, for example, you set the light sensor value to 20 lux, when the room ambient light value is above 20 lux, the light won’t turn on, but when room ambient light value is less than 20 lux, the sensor can turn light on when motion detected within sensing range..
【Delay Time Adjustable- Please set this to its minimum value first then try to figure out your values for the Sensitivity and Light Sensor- this will save your time】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time..
【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it..
【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting, gun safe lighting, pantry lighting, under the bed rails lighting..

Check Stock

SENSKY BS010L DC 12V to 30V 3A Mini Pir Motion Sensor Switch,Occupancy Sensor Switch for Gun Safe, Kitchen Cabinet, Pantry, Closet led lighting (Black-With Light Sensor)

【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting..
【Light Sensor Adjustable】: This function allows you to use the motion sensor in different ambient condition, for example, you set the light sensor value to 20 lux, when the room ambient light value is above 20 lux, the light won’t turn on, but when room ambient light value is less than 20 lux, the sensor can turn light on when motion detected within sensing range..
【Delay Time Adjustable- Please set this to its minimum value first then try to figure out your values for the Sensitivity and Light Sensor- this will save your time】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time..
【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it..
【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting, gun safe lighting, pantry lighting, under the bed rails lighting..

Check Stock

Pentax Wireless Remote Control C

1. Delay / Self Timer (DELAY) Just like the self timer on your camera. The timer remote switch allows you to set any delay (in 1 second increments) up to 99 hours, 99 minutes and 99 seconds..
2. Interval Timer (INTVL) The Interval Timer can be set to any time period up to 100 hours as well. If you set it to 10 minutes, for example, one exposure will be taken every 10 minutes until either the film runs out or the Exposure Count limit has been reached..
3. BULB/Long Exposure (LONG) It allows you to take time exposures up to 100 hours long..
4. Exposure Count (N) This setting allows you to set the times of exposures that will be taken, up to a total 399 times. For example, if you set it to 30 times, then the exposure will be only taken 30 times..

Check Stock

TOPGREENER Dual Tech Humidity Sensor Switch, Infrared PIR Motion & Air Moisture Detection, Bathroom Fan & Light Control, Adjustable Timing, Neutral Wire Required, UL Listed, TDHOS5, White

FAN TIMER SWITCH Dual-tech in-wall humidity control switch that controls both bathroom fan and light simultaneously. Dual technology of passive infrared (PIR) motion sensor switch and humidity sensor switch for fan. Automate light and exhaust fan control to keep you hands-free..
BATHROOM FAN OCCUPANCY DETECTOR Converts bathroom ventilation fan control wall switch with this smart humidity control switch, turning fan ON automatically when humidity exceeds preset level and turning OFF as it drops to normal to eliminate excess humidity.
HUMIDITY SENSOR SWITCH features simple controls and operates in two modes: Occupancy Mode (auto on/off lights, auto on/off fan), and Vacancy Mode (manual on/ auto off lights, auto on/off fan). Adjustable time delay and humidity level.
MOTION SENSOR Two single pole switches to control bathroom light and fan separately.
Energy savings of up to 40% with motion sensing control.
4 time delay settings from 15 sec to 30 min.
120VAC, 3A fan/motors, 500W incandescent/halogen, 150W CFL/LED.
Up to 600 sq.ft coverage, 180 degree field of view.

Check Stock

QUMOX Time Lapse intervalometer Remote Timer Shutter for Canon DSLR 650D 600D 700D Camera

1. Delay / Self Timer (DELAY) : Just like the self timer on your camera. The timer remote switch allows you to set any delay (in 1 second increments)....
2. Interval Timer (INTVL) : The Interval Timer can be set to any time period up to 100 hours as well. If you set it to 10 minutes, for example, one....
3. BULB/Long Exposure (LONG) : It allows you to take time exposures up to 100 hours long..
4. Exposure Count (N) :This setting allows you to set the times of exposures that will be taken, up to a total 399 times. For example, if you set it....

Check Stock

SENCTRL Automatic Vacuum Switch Allow Power Tool/Table Saw To Turn Vac Cleaner/Accessory On And Off Automatically Load Sensing On Delay Prevent Circuit Overload Shop Dust Collector Off Delay

NEW GENERATION: Add a manual switch to support three vacuum run modes: Auto, Off and On. You can not only turn the vacuum on/off automatically with the power tools, but also manually turn the vacuum on/off all time according to your actual condition..
HIGH-QUALITY MATERIALS: Adopt 19.7 inch UL-certified US standard 14AWG power cord which allow passage with a large current more than 30A. Durable PC+ABS V0 grade flame retardant material case, reduce heat during use and extend service life..
TURN ON DELAY. Load Sensing Technology. If the load connected to the 'TOOL' port exceeds 30W, the vacuum connected to the 'VAC' port will automatically delay 1s to start, which helps prevent circuit overloaded by large current if tool and vacuum power-on at the same time..
SHUT OFF DELAY: Automatically delay vacuum turn-off by 7s to continue clearing the remaining airborne debris after the load connected to the 'TOOL' port has stopped. Saving time and electricity, reducing airborne toxin and work area noise that can lead many health problems..
COMPATIBILITY: Support a wide range of cutting tools from handheld devices to large shop saws such as table saw, miter saw, track saw, chop saw, sander, router table, planers, shopvac, remote control outlet, automated vacuum switc....

Check Stock

AC100V~250V Infinite Cycle Delay Timer Timing Switch Relay Turn On Off Module 0.5s ~ 1000min Adjustable Time Delay Switch

【Simple Operation】Timer module enters into an infinite cycle mode when power on, and stops working automatically after the setting time, easy to....
【Adjustable】Relay timer has 0.5s~1000min wide adjustable time range, you can adjust the delay time both at "RUN" time and "STOP" time.
【Practical】The repeat cycle timer module can be used to control the reciprocating stroke, or repetitive power on and off for equipment and....
【Application】The delay timer module is suitable for timer operating equipment, machine repetitive test circuit and fish tank intermittent pump.
【Product Parameter】AC100V~250V voltage, delay timing timer relay switch can be used for 100V/110V/ 120V/ 127V/220V/230V/240V power.

Check Stock

uxcell BWL100 100 mm Pull Rod Linear Position Displacement Sensor for Printer

Shipping list: AC 220V vibration sensor delay module, with ultra-high sensitivity vibration sensor..
AC 220V power supply ultra-high sensitivity vibration delay module plus relay module plus delay three-in-one module, vibration switch module Alarm trigger, with 1 vibration sensor. Relay does not have B1 normally closed end..
corridor delay switch, delay energy-saving products.
Supply voltage: AC 220V power supply, Current: greater than 100mA.

Check Stock