Top T8 Lamp Fluorescent Lighting Reviews

CNSUNWAY LIGHTING 8FT LED Bulbs, 45W 5400LM Super Bright, 5000K Daylight Glow, Frosted Cover, Ballast Bypass, High Output, T8 T10 T12 Single Pin LED Fluorescent Replacement Bulb(4 Pack)

  • 【Connectable】-8FT LED shop lamps can be connected with seamless connectors or T8 connector wires. (Please do not exceed 4 in series at a time) Replace the 150W fluorescent lamp..
  • 【EASY INSTALLATION】 - Easy to replace the traditional fluorescent tube lamp fixture, hard-wired, plug in with T8 power cord. Package comes with T8 metal clips brackets, screws, small connector, a on/off switch power cord and pigtail power cable. You can install these led tube lights on the wall or ceiling..
  • 【EYE PROTECTIVE】 T8 LED Tube Lights with bracket(Integrated) - Daylight white glow 5000 Kevin with clear cover and provide high output. These 8FT lights can be used Indoor shop, grocery, flea market, garage, warehouse, workbench, basement, laundry room, photo studio, gymnasium, practice room...
  • 【HIGH OUTPUT】 - This LED light fixture has 384 LED chips, high output and it will emit up to 9360 lumens bright lighting..
  • 【QUALITY ASSURANCE】 - This 8FT LED Tube Light Single Fixture have 3 years warranty, easy and fast replacement is offered if any quality issue..
Check Stock

The Axiom

  • ✔ Ballast Removal required : Remove the ballast before you install these T8 4ft led bulbs 2pin ends!.
  • ✔ SAVE 65% INSTANTLY - Save 65% on your electricity bill. Replace 80 Watt fluorescent tubes with 28 Watt LED Tube lights (Lighting output 2640 lumens) ..
  • ✔ HIGH BRIGHTNESS - Using imported high brightness LED as light source,Brightness is three times as the same power traditional light source.
  • ✔ EASY INSTALLATION - Can be installed on the traditional G13 4FT T8 lamp socket, bypass the starter and ballast before installation.This 4ft led bulb is double-ended connection. Fast, simple and secure installation..
Check Stock

12-Pack JACKYLED Non-Shunted Turn-Type T8 Lamp Holder UL Socket Tombstone with 10 inches Wires Attached for LED Fluorescent Tube Replacements

  • Specifications: Works with T8 and T12 lamps with medium bi-pin base. Max Wattage: 660W.
  • Max Voltage: 601V. Great for retrofitting your fluorescent fixtures to LED tubes, replacing old florescent lamp holders and more..
  • UL Listed: Made from high quality fireproof PC, the T8 lamp holders are heat resistant and 101% safe from fire hazard, durable even after years of use..
  • Easy to Use: Get your project done in minutes with JACKYLED T8 Lamp Holder Socket Tombstone with 10” 18 AWG Wire. Just connect the wires, plug the tube in and twist, a plug-and-play solution for your lighting projects..
  • Wide Application: Perfect for anywhere from home, office, basement, closet to studio that needs a lighting retrofit, while staying low profile between the T9 lights..
  • 100% Satisfaction: We strive to provide each customer with the highest standard of customer service to ensure you have a pleasant shopping experience. If you have any issues, inquiries or need assistance, please feel free to contact us directly..
Check Stock

JESLED T8 8FT LED Light Bulbs, 50W 6000LM, 5000K 4Pack, Single Pin FA8 Tombstone Holder 12-Pairs,T8 U Clips Holder Bracket for 8FT LED Light Bulbs 24-Pack

  • 【Bright and Energy Efficient】 - JESLED T8 8ft LED bulb can brighten your space with 6000+ lumens. Save 62% on your electricity bill instantly when you replace your old 130-watt fluorescent tubes with high-output 50-watt 8-foot LED tubes..
  • 【Design Science】- JESLED Shatterproof Single Needle 8ft LED Tube has an excellent lifespan of over 50,000 hours! Double row LED chips, V-shaped 270 degree angle design, 6000k, make the product brighter and better, ideal for workbench, basement, garage, office, and shop general lighting..
  • 【Easy Installation】- JESLED fa8 8ft LED bulbs are powered by double ends and require simple, energy-efficient ballast bypass (straight line) installation. Note: Please install this product away from radios, remote control doors, and other places that may cause electromagnetic interference..
  • 【Fluorescent Tube Replacement】 - JESLED Single Pin 8ft LED Replacement is perfect for fluorescent light fixtures. They are compatible with existing T8, T10, and T12 fluorescent fixtures, making LED conversion easier than ever..
  • 【Application】-This lamp holder is suitable for changing the single-ended or double-ended power supply route, and the buckle can better fix the 8ft long lamp tube..
Check Stock

20-Pack JACKYLED Screw Type T8 Lamp Holder with Wires UL Non-shunted Tombstone Light Socket for LED Fluorescent Tube Replacements

  • Specifications: Works with T8 and T12 lamps with medium bi-pin base. Max Wattage: 660W.
  • Max Voltage: 608V. Great for retrofitting your fluorescent....
  • UL Listed: Made from high quality fireproof PC, the T8 lamp holders are heat resistant and 108% safe from fire hazard, durable even after years of....
  • Easy to Use: Get your project done in minutes with JACKYLED T8 Lamp Holder Socket Tombstone with 10” 25 AWG Wire. Just connect the wires, plug the....
  • Wide Application: Perfect for anywhere from home, office, basement, closet to studio that needs a lighting retrofit, while staying low profile between....
  • 108% Satisfaction: We strive to provide each customer with the highest standard of customer service to ensure you have a pleasant shopping experience.....
Check Stock

SinLoon UL-LP Certification T5 T8 LED Lamp Connecting Wire Ceiling Lights Daylight LED Integrated Tube Cable Linkable Cords for LED Tube Lamp Holder Socket Fittings with Cables(6.5FT/2M,2-Pack)

  • Item name: UL certified power cord T5 /T8 Double Connector. Length: 200Cm(6.5 foot). Specification: 3 * 0.824㎡ copper wire. Working voltage range: 110V-250V. Max Output: 6A. Materials: PVC insulation. The long-term service temperature is 80℃~105℃..
  • UL Certified power cord A perfect solution for connecting led strip with controller or strip to strip connection..
  • UL Listed extension cord the products are through 100% aging test and strict quality control.No need welding,no need soldering,easy use..
  • UL-LP Certification T5 T8 LED lamp connecting wire used for fluorescent lamps, LED lamps, advertising light box (shop illuminated signs) halogen, filament or CFL light bulb and more..
  • Package: 2 pcs T5 T8 LED lamp connecting wire+4pcs Clips(Note: Not suitable NVC lighting and sanxiong pak lighting !).
Check Stock

Lithonia Lighting 3348 Lighting Two-Light Fluorescent Ceiling Fixture White,4-feet

  • 4', 2 lamp, T8 utility wrap fixture, 120V residential electronic Ballast, white steel housing, clear Acrylic lens, energy star rated, title 24....
  • Diffuser features a continuous-interlocking design for easy installation, lamp access and cleaning.
  • Lithonia Lighting 2-light fluorescent white ceiling fixture.
Check Stock

EFAYCRR (6 Pairs) Tombstone Base Holder Socket Connector with T8 T10 T12 Single Pin FA8 8ft LED Bulb Light Replacement Fluorescent Plunger Lampholder

  • 【UL Standard】Single Pin T8 lamp holders are UL listed.Made of Flameresistant material..
  • 【Widely used 】FA8 tombstones fit for all kind of T8 T10 T12 single pin fluorescent and LED tube lamp, advertising light box and more.Perfect for lighting up your home or office, basement, closet, studio, etc. Hold the lamp tightly..
  • 【Electronic Parameter】Max Current 6A, Max wattage 660w,Voltage: 100-600V..
  • 【Easy to install】Snap-in or Slide-on Installation, Can Directly Connect with The FA8 Single Pin Light Tube..
  • 【Package included】6 Pairs Single Pin FA8 Sockets for 10 tubes (without cable).
Check Stock

Ghiuop 25-Pack T8 LED Bulbs 4 Foot Tube Light, 4ft LED Shop Garage Warehouse Light, 20W 5000K 2600LM Daylight White, Fluorescent Lights Tube Replacement, Ballast Bypass, Dual-end Powered, Clear Cover

  • 【5000k Super Bright & Energy Saving】This T8 LED bulb has 2600+ lumens and a CRI rating of 80+. Each 4ft led light tube has a low power consumption of 20w, instantly saving you 60% on your electricity bill when you replace your old 40 watt fluorescent tube with 20w LED lamp. The LED t8 light tube bulbs are widely used in shop, warehouse, garage, mall, hotel, office, convenience store, gas station, parking lots etc..
  • 【Premium Quality & Long Lifespan】: T8 LED bulbs are made of aluminum. Compared with the glass light tube, Ghiuop light tubes not only have a larger luminous surface, but also safer. Moreover, the aluminum light tubes can better dissipate heat and increase the service life of the fixture(50,000+ hour lifespan, last up to 20+ years). Reduce led light tube replacement frequency, saving money and time..
  • 【Reliable Lighting & Shatterproof 】Zero flickering light, zero delay, and zero worries with 48" LED t8 lights that provide high quality indoor and outdoor lighting. The 4ft led bulbs have been packed very well with Styrofoam cushioning and end cap to protect them. t8 led light has shatterproof property because it is equipped with an aluminum body and a frosted lens..
  • 【Easy Ballast Bypass Installation】Fluorescent replacement is simp....
Check Stock

Four-Bros Lighting LED High Bay Light 6 Lamp 5000K Daylight White, 5 Year Warranty, Industrial Grade, Warehouse, Shop, Garage Lighting - UL Listed, DLC Approved, Made in USA, BAA Certified, Pack of 6

  • #1 Rated Made in USA LED High Bay. BAA Certified Fixture.
  • ✔ Single-sided 18-watt LED T8 tubes included with every LED High Bay purchase✔ MAINTENANCE-FREE - No ballast-drama anymore. This 6 Lamp LED high bay light fixtures operates (6) LED T8 tube lights that bypass the ballast. Simply install the LED tube in its marked location and twist. Our LED high bays must be wired to operate 6 LED T8 Tubes.
  • ✔ MAINTENANCE-FREE - No ballast-drama anymore. This 6 Lamp LED high bay light fixtures operates (6) LED T8 tube lights that bypass the ballast. Simply install the LED tube in its marked location and twist. Our LED high bays are rewired to operate 6 LED T8 Tubes17,160 Lumens (Brighter than Fluorescent T5HO) 5000K Daylight White Color Temp.
  • ✔ HOW DOES IT WORK - Each high bay Fixture comes with all the wiring and tombstones needed to be installed on the field. THESE DO NOT COME PREWIRED..
  • ✔ 5 YEAR WARRANTY - Buy with confidence, risk-free. Four Bros Lighting five-year warranty got you covered! Contact us for an easy and fast replacement..
Check Stock

NYLL - 18 Inch/ 18' Plug & Play LED Tube – Daylight (6000K) T8 LED Lamp Directly Relamp & Replace 15W Fluorescent Bulbs F15T12, F15T8, FO13/865 (Without rewiring or Modification) - Ballast Required!

  • Directly relamp and replace the 15 watt fluorescent bulbs F15T12, F15T8, FO13/700, FO13/800 without rewiring or modification. LED lamp is powered by the ballast, which means you can eliminate the need to hire a costly electrician to do any modification. Instant ROI!.
  • Designed with flexibility in mind, T8 diameter tube lighting fits T8/ T10/ T12 applications as they all use Medium Bi-Pin base, pin spacing 13 mm, end connector.
  • All plastic diffuser and construction for better light distribution, less or no spot reflections. Energy saving of 40% from 15 watts to 9 watts with 990 lumens output.
  • T8 LED lamp works with traditional magnetic ballasts and electronic ballasts. It's fully compatible with Instant Start, Programmed Start, Rapid Start ballasts and legacy pre-heat magnetic ballasts.
  • 2-year, warranty does not require registration.
  • however, each warranty claim is subject to approval and applicable to the original purchaser as identified on the purchase invoice. Please contact us directly for warranty information for this product.
Check Stock

Luxrite 12-Pack 4FT T8 LED Tube Light, Type A+B, 18W=32W, 3 Colors 3500K | 4000K | 5000K, Single and Double End Powered, Plug and Play or Ballast Bypass, 2340 Lumens, F32T8, Frosted Cover, UL, DLC

  • ...sed to change between 3 cct color temperatures. Enjoy your lights at 3500K natural white, 4000K cool white, or 5000K bright white. Feel free to adjust your lights further by taking advantage of the dimming feature when using a dimming capable ballast..
  • PLUG & PLAY - Use these as a direct replacement to your existing fluorescent tube lights that make use of the ballast already in your ceiling fixture. These 48inch LED bulbs are compatible with an extensive list of ballasts so you can just install these without making any adjustment. No need to change your shunted lamp holders or tombstones. Check ballast list for compatibility..
  • BALLAST BYPASS - Not using a ballast? Feel free to hardwire these directly since these can handle single end or dual end powered connections. Capable of both 120V and 277V wiring installations and can work with existing shunted lamp holders/tombstones when dual end connected. If using a single end install, you will need to use non-shunted lamp holders/tombstones..
  • CONTINUOUS LIGHT - Built with an astounding 50,000 hours of lifetime which means no replacement will be needed for the next 45 years, based on 3 hrs/day use. Each t8 LED bulbs 4 foot has a frosted cover and is shatterproof which allows for safer installation compared to....
Check Stock

LUXRITE 4FT T8 LED Tube Light, Type A+B, 18W=32W, 3 Colors 3500K | 4000K | 5000K, Single and Double End Powered, Plug and Play or Ballast Bypass, 2340 Lumens, F32T8, Frosted Cover, UL, DLC (4 Pack)

  • ...sed to change between 3 cct color temperatures. Enjoy your lights at 3500K natural white, 4000K cool white, or 5000K bright white. Feel free to adjust your lights further by taking advantage of the dimming feature when using a dimming capable ballast..
  • PLUG & PLAY - Use these as a direct replacement to your existing fluorescent tube lights that make use of the ballast already in your ceiling fixture. These 48inch LED bulbs are compatible with an extensive list of ballasts so you can just install these without making any adjustment. No need to change your shunted lamp holders or tombstones. Check ballast list for compatibility..
  • BALLAST BYPASS - Not using a ballast? Feel free to hardwire these directly since these can handle single end or dual end powered connections. Capable of both 120V and 277V wiring installations and can work with existing shunted lamp holders/tombstones when dual end connected. If using a single end install, you will need to use non-shunted lamp holders/tombstones..
  • CONTINUOUS LIGHT - Built with an astounding 50,000 hours of lifetime which means no replacement will be needed for the next 45 years, based on 3 hrs/day use. Each t8 LED bulbs 4 foot has a frosted cover and is shatterproof which allows for safer installation compared to....
Check Stock