Top Spi Interface Reviews

5PCS 0.96 Inch OLED Display Module, PEMENOL 28 x 64 Pixel I2C IIC Serial 1 OLED LCD Display Module with SSD1306 Driver for Arduino Raspberry Pi and ESP8266（White Light）

  • This is a new 2.8 inch serial SPI color display module with touch function.
  • Designed with one socket for memory card.
  • With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface.
  • 5V compatible, use with 3.3V or 5V logic.
Check Stock

Arducam Mini Module Camera Shield 5MP Plus OV5642 Camera Module, Compatible with Arduino UNO Mega2560 Board

  • Arducam Mini Module Camera Shield 5MP Plus OV5642 Camera Module is a general purpose high definition 5MP SPI camera, which reduce the complexity of the camera control interface.
  • It integrates 5MP CMOS image sensor OV5642, and provides miniature size, as well as the easy to use hardware interface and open source code library.
  • The Arducam Mini is compatible with Arduino, Raspberry Pi, Raspberry Pi Pico,ESP8266, Maple, Chipkit, Beaglebone black, as long as they have SPI and I2C interface.
  • Support JPEG compression mode, single and multiple shoot mode, short movie recording, one time capture multiple read operation, burst read operation, low power mode and etc..
  • It can be used in IoT, Robot, Wildlife, HDR and Other battery-powered products or scientific image processing applications.
Check Stock

HiLetgo 2.2 Inch ILI9341 SPI TFT LCD Display 240x320 ILI9341 LCD Screen with SD Card Slot for Arduino Raspberry Pi 51/AVR/STM32/ARM/PIC

  • Durable hard PCB board and SD card socket, ideal for 5110 interface.
  • 2.4 inch TFT LCD shield without touch panel, fast to operate.
  • Support Serial SPI Mode, Interface 4-Wire SPI, Need 4 IOs from your MCU only.
  • Support a variety of microcontroller IO connection, professional and practical.
  • 5V compatible, use with 3.3V or 5V logic.
Check Stock

3.3V 2.4 inch TFT LCD Touch Panel for Industry with PCB ILI9341 240x320 Pixels for Home

  • This is a new 2.8 inch serial SPI color display module with touch function, 5V compatible, use with 3.3V or 5V logic..
  • Support analog SPI and hardware SPI, Designed with one socket for memory card..
  • With PCB plate (including power supply IC, Memory Card), compatible with 5110 interface..
  • This kit requires professional knowledge and ability, please make sure you know how to use it..
  • Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering..
Check Stock

2.9inch E-Ink Display Module 296x128 Pixel White,Black Two-Color 3.3V/5V E-Paper Screen LCD Support Partial Refresh SPI Interface for Raspberry/Jetson Nano/Ard/Nucleo

  • 2.9inch, 296x128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on..
  • Display color: black, white. Grey level: 2. Partial refresh time: 0.3s. Full refresh time: 2s. Refresh power: 26.4mW(typ.). Standby power: 170°..
  • Interface: 3-wire SPI, 4-wire SPI. Outline dimension: 89.5mm × 38mm. Display size: 66.89mm × 29.05mm. Dot pitch: 0.138 × 0.138..
  • Onboard voltage translator, compatible with 3.3V/5V MCUs.Operating voltage: 3.3V/5V. Ultra low power consumption, basically power is only required for refreshing.No backlight, keeps displaying last content for a long time even when power down.
Check Stock

SEEU. AGAIN 4pcs 0.96 Inch I2C OLED Display Module IIC SSD1306 128x64 LCD White with 4 Pin Female to Female Du-pont Wire

  • I2C mode up to 400Khz, configurable slave address.
  • Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
  • 4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
  • Backlight brightness and contrast controlled by software commands.
  • Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.
Check Stock

Geniatech XPI-3288 Android Single Board Computer Development Board Moudle,Rockchip RK3288 Quad Core CPU 2G RAM, 16GB EMMC Flash Motherboard

  • Card-sized High Performance Board, Rockchip RK3288 with Quad-core Cortex-A17 up to 1.6GHz, 2G RAM, 16GB eMMc flash, faster read / write speeds for the OS, applications and file storage.
  • 4*USB2.0, 1*HDMI Out, 1*Micro USB, 1*UART, 1*GPIO interface, WiFi and 1000M LAN interface, Micro SD card (TF card : Max64G).
  • Multiple DIY use Single Board Computer, use the Form Factor of Raspberry Pi, DIY Friendly Design: 40 Pin GPIO header with I2S, I2C, SPI, UART, etc.
  • According to the definition of Raspberry Pi, which is suitable for the field of programming education for teenagers.
  • Compatibility and Extensibility: 40 Pin header enables hardware re-use by maintaining compatible alternate pin functions like I2S, I2C, SPI, UART, and so on.
Check Stock

1.54 Inch E-Paper Screen Display Module Resolution 200x200 3.3v E-Ink Electronic Display with Embedded Controller SPI Interface Support Partial Refresh for Raspberry Pi/Arduino/Nucleo/Jetson Nano

  • This is an E-Ink display module, 1.54inch, 200x200 resolution, with embedded controller, communicating via SPI interface, supports partial refresh..
  • No backlight, keeps displaying last content for a long time even when power down.
  • Ultra low power consumption, basically power is only required for refreshing.
  • Onboard voltage translator, compatible with 3.3V/5V MCUs.
  • SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc..
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock

Adafruit ItsyBitsy M4 Express Featuring ATSAMD51

  • The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
  • This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
  • Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
  • There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..
Check Stock

Ingcool 2.9inch e-Ink Display Module, 296x128 Resolution Two-Color e-Paper Display epaper Screen for Raspberry Pi/Jetson Nano/Arduino/Nucleo,SPI Interface Support Partial Refresh

  • This is an E-Ink display module, 2.9inch, 296x128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh..
  • Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on..
  • No backlight, keeps displaying last content for a long time even when power down.Ultra low power consumption, basically power is only required for refreshing.
  • SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/Nucleo, etc..Onboard voltage translator, compatible with 3.3V/5V MCUs.
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock

Teyleten Robot GY-291 ADXL345 Digital 3-Axis Acceleration of Gravity Tilt Module IIC SPI for Arduino 3pcs

  • Brand new original ADXL345 chip, quality assurance.
  • According to the 16-bit two's complement format, it can be accessed through the digital interface SPI (3-wire or 4-wire) or I2C.
  • ADXL345 is very suitable for mobile device applications. It can be used for tilt sensing applications while measuring static acceleration of gravity,....
  • With high resolution (13 bits) measurement up to ±16g. The digital output data is in 16-bit two-valued complement format, which can be passed through....
  • Communication method: IIC / SPI communication protocol.
Check Stock

16x2 Blue LCD Module Controller HD44780 Based for Arduino by Corpco

  • Size: 1.54in screen can provide clear view for you..
  • Drive Voltage: 3.3V-5V. The pin has good contact performance, ensure stable working.
  • Material: Adopted of high quality electronic components, and preciseness process, ensure for the durability.
  • Resolution: 128 x 64. Great workmanship, easy and convenient to install. Driver IC: SSD1309, compatible with SSD1306. Interface: SPI interface I2C interface.
  • Optional Style: Display White, Display Yellow, Display Blue. Available in three colors for your choice..
Check Stock

Fafeicy 2.8\ ILI9341 SPI TFT LCD Touch Panel, 64k Serial Port Module, with PCB, 5V/3.3V 240x320, Integrated Circuit Ic

  • SPI TFT LCD Touch Panel is designed with one socket for sd card..
  • With PCB plate (including power supply IC, SD), compatible with 5110 interface.
  • 5V compatible, use with 3.3V or 5V logic..
  • This is a new 2.8 inch serial SPI color display module with touch function..
  • We strive to provide a product of the highest quality and the best customer experience, if you are not completely satisfied, do not hesitate to contact us at any time..
Check Stock