Top Solide State Relay Reviews

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

• Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
• Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
• Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
• This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
• Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

2018 Dell Inspiron 17 17.3

• 17.3-inch HD+ (1600 x 900) Anti-Glare LED-Backlit Display with 720p Webcam.
• 7th Generation Intel Core i5-7200U Processor @ 2.50GHz (2 cores, 3M Cache, up to 3.10GHz).
• 256GB Solide State Drive + 1TB 5400 RPM SATA Hard Drive, No Optical Drive.
• 802.11ac Wireless LAN, Bluetooth 4.2, 2 x USB 3.0, 1 x USB 2.0, 1 x HDMI, 1 x Headphone/Microphone Combo Jack.

Inkbird SSR Solid State Relay SSR 40DA for PID Thermostat Temperature Controller

• Model No.: SSR-80DA；If you want to reach 80A, you need to add a large heat sink and fan.
• output Voltage : 24-480vac；Special attention:This relay cannot be used for more than 30A for a long time.If that actual use current exceeds 15A，It is necessary to separately configure the heat sink..
• Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t).
• material : metal, plastic, electronic parts.

SparkFun Qwiic Quad Solid State Relay Kit - Attach 4 Solid State relays to a Single PCB - Control Some serious Power All from The Easy-to-use Qwiic Connect System - configurable I2C

• This kit allows you to assemble up to four of these solid state relays on a single PCB and control them all via I2C from your favorite microcontroller..
• The Quad Solid State Relay Kit comes with four solid state relays rated up to 40A at voltages between 28-380 VAC so you can switch some serious power with this board all from a single Qwiic connector attached to a low-powered microcontroller..
• Features: Operating Voltage: 2.5-3.6V (3.3V recommended). I2C Address: 0x08 (Default), 0x09 (Alternate via jumper). Max Current (Through Relay): 40A (24-380VAC). Zero Cross Trigger. Normally Open Circuit Only.
• Includes: 1x Qwiic Quad Solid State PCB. 4x Solid State Relay - 40A (3-32V DC Input). 8x 4-40 Hex Nut. 8x 3/8in. Phillips Machine Screw - 4-40 Thread. Hook-up Wire 8" - 22 AWG (Red). Hook-up Wire 8" - 22 AWG (Black).
• Assembly required. Tools are not included. You will need a screwdriver and wire clippers/strippers..

AITRIP 1PCS 8 Channel 5V Solid State Relay Module Board High Level Trigger Compatible with Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC (1PCS)

• Solid State Relay Module Board has been assembled, and electrical test passed.
• Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch).
• Has been assembled, and electrical test passed. Led indicator for each relay. Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch) Input control signal voltage: 0V - 0.5V Low stage (SSR is OFF), 0.5V - 2.5V (unknown state), 2.5V - 20V High state (SSR is ON).
• Load voltage range: 75 to 264VAC (50/60Hz).
• Load current: 0.1 to 2 AMP Standard interface that can be controlled directly by microcontroller (Compatible with Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

AEDIKO 4pcs Relay Module DC 5V Relay Switch 1 Channel Relay Board with Optocoupler Isolation Support High or Low Level Trigger

• Fault-Tolerant Design: Fault Tolerant Design, Even if the Control Line is Broken, the Relay will not Operate.
• All Interfaces of Relay can be Wired Out Through the Terminals Directly,Normally Open and Normally Closed.
• Optocoupler Isolation:1 Channel Relay Board use Optocoupler Isolation that has Strong Driving Ability and Stable Performance ,The Isolation Circuit Prevent Damages to I / O Port by Relay Switch Current.
• Jumper Design: The Relay Module has a Jumper That You Can Set Rather the Unit State Changes with High or Low Signal. Has Screw Terminals for Relay (NC,C,NO) and for Input.
• Wide Application: DC 5V Relay Module Works Well with ARM /PIC /AVR /MCU/Raspberry/CNC Machine/ PS4 etc..

Twidec/Output Single Phase SSR Solid State Relay 80A 3-32V DC to 24-480V AC SSR-80DA

• Model No.: SSR-80DA；If you want to reach 80A, you need to add a large heat sink and fan.
• output Voltage : 24-480vac；Special attention:This relay cannot be used for more than 30A for a long time.If that actual use current exceeds 15A，It is necessary to separately configure the heat sink..
• Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t).
• material : metal, plastic, electronic parts.

HELLA 007903001 24V 10/20A SPDT Relay , Black

• 24 Volt 10/20A SPDT relay for automotive use.
• The relay can be operated by a dashboard switch or another 24 Volt input.
• The SPDT change over relay switches electrical load from one use to another.
• Change over relays are used for switching 2-state applications such as heated rear windows, fan motors, or the movement of a sliding sunroof.

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

• This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
• Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
• These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
• Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
• And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
• Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..

SainSmart 5V 2A 4 Channel Solid State Relay Module High Level Trigger Black for Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

• This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
• Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
• These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
• Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
• And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
• Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

Solid State Relay SSR-40AA 40A AC to AC Input 80-250V AC and Output 24-380V AC (SSR-40 AA)

uxcell BEM-14840DA 3-32V DC to 24-480V AC 40A Output Single Phase SSR Solid State Relay

• Total Size (Approx.) : 58 x 45 x 32mm / 2.3" x 1.8" x 1.26" (L*W*T).