Top Solid State Latching Relay Reviews

Two Position Low V Actuator w/End Switch

Output: fan relay, alarm relay and 4-20ma current loop.
Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
Mounts on a standard 4” x 4” electrical box.
5 a spdt fan relay controls starters of exhaust fans.

Model No.: SSR-80DA；If you want to reach 80A, you need to add a large heat sink and fan.
output Voltage : 24-480vac；Special attention:This relay cannot be used for more than 30A for a long time.If that actual use current exceeds 15A，It is necessary to separately configure the heat sink..
Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t).
material : metal, plastic, electronic parts.

Output: fan relay, alarm relay and 4-20ma current loop.
Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
Mounts on a standard 4” x 4” electrical box.
5 a spdt fan relay controls starters of exhaust fans.

...y for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it..
3. Remote Relay with 3 Modes of Operation – Use a jumper to configure 3 modes of operating selection pulse / momentary, hold / toggle and latching mode. 4 independent relay channels can either work together (in latching) for polarity reversing or individually (in pulse / hold) to control different electronics, such as two channels for garage door controller motor, the other two for entry lights..
4. Easy and Flexible Switch Relay – The wireless relay kit is a perfect remote switch for those hobbyists with home automation DIY projects or business Industrial electrical. The power input voltage is 12V, and each receiver’s relay capacity is up to [email protected] and [email protected]..
5. Wide Applications – The wireless remote control switch can be widely used in short and long range turn devices on / off wirelessly, anti-theft alarm control panels, lifts, boats, motor-driven curtain, roller blinds, garage door openers, gate barriers, motorcycles, vehicles, cars, trucks, RVs, electric generator, electric door release locks, windows, manual switches extender, LED lighting ....

Model No.: SSR-80DA；If you want to reach 80A, you need to add a large heat sink and fan.
output Voltage : 24-480vac；Special attention:This relay cannot be used for more than 30A for a long time.If that actual use current exceeds 15A，It is necessary to separately configure the heat sink..
Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t).
material : metal, plastic, electronic parts.

Special attention: the current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-40DA Solid State Relay 40A DC to AC.
Input voltage: 3-32V DC Output voltage: 24-380V AC.
Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).

Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

...y for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it..
3. Remote Relay with 3 Modes of Operation – Use a jumper to configure 3 modes of operating selection pulse / momentary, hold / toggle and latching mode. 4 independent relay channels can either work together (in latching) for polarity reversing or individually (in pulse / hold) to control different electronics, such as two channels for garage door controller motor, the other two for entry lights..
4. Easy and Flexible Switch Relay – The wireless relay kit is a perfect remote switch for those hobbyists with home automation DIY projects or business Industrial electrical. The power input voltage is 12V, and each receiver’s relay capacity is up to [email protected] and [email protected]..
5. Wide Applications – The wireless remote control switch can be widely used in short and long range turn devices on / off wirelessly, anti-theft alarm control panels, lifts, boats, motor-driven curtain, roller blinds, garage door openers, gate barriers, motorcycles, vehicles, cars, trucks, RVs, electric generator, electric door release locks, windows, manual switches extender, LED lighting ....

Special attention: The current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-25DA Solid State Relay 25A DC to AC.
Input voltage: 3-32V DC Output voltage: 24-380V AC.
Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).

Special attention: the current of this product is 10A for a long time.A large heat sink or fan need to be added.Model: SSR-40DA Solid State Relay 40A DC to AC.
Input voltage: 3-32V DC Output voltage: 24-380V AC.
Item size: 6.2 x 4.5 x 2.3cm/ 2.4 x 1.8 x 0.9inch(L*W*H).