Top Shank Length Reviews

0.27 Caliber Green Shot Strip Loads, Power Fasteners Actuated Powder Loads (100-Count)

  • Washer pins - powder fastener actuated fastening system, Increases bearing surface against the material to be fastened..
  • Shank diameter = .14Shank diameter = .145.
  • Meets the requirements of toughness and durability that enable them to penetrate dense concrete and structural quality steel.
Check Stock

Malco MALCOMBO11 2 in. Impact Hex Driver (1/4 in, 5/16 in, 3/8 in.), 3 Piece Set

  • 1- each of the following MSH14IS, MSH516IS, MSH38IS..
  • 1- Of each 1/4 hex shank in 2-inch length, 5/16 hex shank in 2-inch length & 3/8 hex shank in 2-inch length..
Check Stock

HSS 1-1/4\ MT3 Taper Shank Drill

  • Size: 42.00mm, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 10-1/8, Overall Length: 17-1/8, Shank Size: 5MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

Qualtech 7/8\ HSS 3MT Taper Shank Drill Bit, DWDTS7/8

  • Size: 3/4, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 5-7/8, Overall Length: 9-3/4, Shank Size: 2MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

Drill America 7/8 Bridge/Construction Reamer with Magnetic Hex Shank DWR Series

  • Hex shank bridge reamers are high speed steel and are used to align existing holes prior to bolt or rivet installation.
  • Point is tapered to permit entry into overlapping holes. Short length facilitates use in areas with limited access.
  • Heavy-duty hex shank has six flats and is designed for portable pneumatic tools. For additional safety magnet inside the shank of reamer to secure in socket.
Check Stock

Drill America 13/16\ Bridge/Construction Reamer with Magnetic Hex Shank, DWR Series

  • Hex shank bridge reamers are high speed steel and are used to align existing holes prior to bolt or rivet installation.
  • Point is tapered to permit entry into overlapping holes. Short length facilitates use in areas with limited access.
  • Heavy-duty hex shank has six flats and is designed for portable pneumatic tools. For additional safety magnet inside the shank of reamer to secure in socket.
Check Stock

Qualtech 1-47/64\ HSS 5MT Taper Shank Drill Bit, DWDTS1-47/64

  • Size: 1-47/64, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 10-1/8, Overall Length: 17-1/8, Shank Size: 5MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

Qualtech 1-1/64\ HSS 3MT Taper Shank Drill Bit, DWDTS1-1/64

  • Size: 1-3/4, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 10-1/8, Overall Length: 17-1/8, Shank Size: 4MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

Drill America 1/2\ Carbide Tipped 2MT Taper Shank Drill Bit, DWDTS Series

  • Size: 25/32, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 6, Overall Length: 9-7/8, Shank Size: 2MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

Qualtech 1-1/32\ HSS 3MT Taper Shank Drill Bit, DWDTS1-1/32

  • Size: 26.00mm, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 6-1/2, Overall Length: 11-1/8, Shank Size: 3MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

9 Pieces Tungsten Carbide Single Cut Rotary Burr SET 1/4 Shank Fit 6mm Shank

  • Shank diameter:6mm, Shank Length: 35mm/Total length: 45-50 mm.
  • 9 pieces Tungsten Carbide Single Cut Rotary Burr SET 1/4" shank Fit Dremel.
Check Stock

Qualtech 42.00mm HSS 5MT Metric Taper Shank Drill Bit, DWDTSMM42.00

  • Size: 2-7/32, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 10-1/4, Overall Length: 17-3/8, Shank Size: 5MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock

1-1/64\ HSS Extra Long Taper Shank Drill Bit, 24\ OAL, MT3, Michigan Drill Series 124

  • Size: 1-1/2, Material: High Speed Steel, Finish: Black Oxide, Flute Length: 9-3/8, Overall Length: 15, Shank Size: 4MT, Shank Type: Taper, Style: Taper Shank, Cutting Angle: 118, Point Type: Conventional Point, Number of Flutes: 2, Cutting Direction: Right Hand.
Check Stock