Top Servo To Reverter Board Reviews

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
2.You should connect higher power supply for higher-power servo.
3.Make sure servo are connected properly, otherwise they will not move..
Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..

Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
Great for jumping from board to board or just about anything else..
There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
Length:100mm Type:JR Plug Servo Extension wire (Male to Male).

Check Stock

6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat

Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..

Check Stock

KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino

This expansion board can directly stack on the controller R3 board and can drive up to 16 servos.
Uses I2C input, just occupy A4 and A5 interface on the control board.
Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits.
Servo power supply independent V + input up to 6V.
How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product..

Check Stock

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
Includes a total of over 190 electronic parts and components.

Check Stock

sb components Motor Driver Board for The BBC Micro bit 2 Channel DC Motors and 3 Channel Servos Motors Motor Driver for Micro bit BBC microbit Motor Driver Board

micro:bit edge connector, directly pluggable.
2x DC motor interfaces, 3x servo interfaces.
Integrates 5V regulator, up to 3A output current.
Onboard multi connector options for DC motors in different specifications, onboard standard servo headers.

Check Stock

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

MKS servo42C is a product developed by MKS to meet market demand. The closed-loop motor uses the motor's rotation angle feedback to the drive circuit to detect whether every step that should be taken has been taken to prevent losing steps. If a closed loop occurs, the motor will make up or lose steps through the feedback information, and the blue LED on the closed loop module will light up..
Support 1-256 subdivision,odd subdivision (such as 11 subdivision) is also available. And support motors with 0.9 degree or 1.8 degree. Maximum speed 1000RPM. With usart interface, you can connect the computer by serial port, for parameter adjustment and query..
Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User metho....

Check Stock

Barnabas Robotics Servo Motor Tester Kit | 180 Degree 9g Servo Motor + RC Servo Tester Controller + 6V Battery Holder

[CONVENIENT, ALL-IN-ONE KIT FOR TESTING SERVO MOTORS] Experiment with servo motors with this all-inclusive kit. Includes 9g servo motor + servo tester controller + 6V battery holder at a low price!.
[9G Servo Motor] 180 degree range of motion. Includes 3 types of servo horns..
[4 CELL x AA BATTERY HOLDER] Fits 4 x AA batteries, which produces 6V for your servo tester and servo motors..
[SERVO TESTER] Includes 3 modes to test servo motors or ESC.
[GREAT FOR RC APPLICATIONS] Use as a power source for robotics, RC cars, helicopters, planes, boats and or any hobby projects.

Check Stock

WEISHUJI 10PCS 25T Aluminum Servo Horns Arms, M3 Threads Metal Steering Arm for Towerpro, HSP, HD power, Futaba, Axial, Savox, Xcore, Standard Servos Motors, MG995 MG996R MG946R, S3003 etc servo (Red)

25T Aluminum Servo Horns Arms are suitable for mostly 25T Standard Servo Motor, and M3 Threads Metal Steering Arm is compatible with Towerpro HSP HD power Futaba Axial Savox Xcore Standard Servos Motors MG995 MG996R MG946R S3003 etc servo..
25T Aluminum Servo Horns Arms are made of strong aluminum, 25T Aluminum Servo Horns M3 Threads are hard to break..
25T Aluminum Servo Horns Arms are of dimension 35x15x6mm, and Metal Steering Arm behaves very well on your RC models..
25T Aluminum Servo Horns Arms are djustable type servo arm, and M3 Threads Metal Steering Arm have two steel bolts to secure the split-clamp onto the servo output..
Package of 25T Aluminum Servo Horns Arms include: 10 x 25T Aluminum Servo Horn-Red, M3 Threads Metal Steering Arm, 25T Aluminum Servo Horns M3 Threads some hardware.

Check Stock

MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board Controller Card for CNC Engraving Servo Motor Stepper Motor Servo motor

【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....

Check Stock

OSOYOO Robot Rc Smart Car DIY Kit to Build for Adults Teens with Servo Power Steering Motor, WiFi, Bluetooth, Code Programmable Compatible with Arduino UNO

Most Advanced Technology in the Market Today: the OSOYOO Robot Car kit features a servo power steering motor that controls the axles to turn the wheels. This electric power steering system enables a highly automated driving experience that imitates real-world full-sized vehicles.
Do-it-yourself Starter Robot Car Building Kit: allows adults, teens, and all students to learn valuable skills, fully compatible with Arduino UNO R3 board, it will help you learn about electronic circuits, programming sensors and actuators, the Internet of Things (IoT), coding, electronics, mechanical engineering and hands-on experience in robotics.
Package includes all the technical modules, parts, and sensors you need to build a fully functional robotic car: such as MCU board for R3, OSOYOO motor shield, OSOYOO ESP8266 WIFI shield, HC Bluetooth module, line tracking module, ultrasonic sensor, micro servo motor, battery, and charger.
Multifunctional and features all the highly advanced intelligent features and driving modes that you expect for a robot car: which includes: auto-go, line tracking, ultrasonic avoidance, Wifi IOT control, Bluetooth App control, compatible with Android and Apple IOS devices via an app developed in house exclusively for OSOYOO.

Check Stock

TecUnite 20 Pieces 3-Pin Extension Cable Cord Female to Male Wire Connectors for Servo Extension Connection Control Board Remote Control Parts(4 Sizes)

Servo extension cord sizes: have 4 different lengths of 10 cm/ 3.94 inch, 15 cm/ 5.9 inch, 30 cm/ 11.8 inch and 50 cm/ 19.7 inch, each length has 5 pieces servo extension cords.
Application: these servo extension leads are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, remote control car, RC Car.
3-Pin servo extension wire: each servo extension has 3 pieces of 0.08TS wires, universal model.
Connectors with 3 pins and have an angle in case you will install incorrectly, convenient for use.
Female to male servo extension cable: featured with female connector on one side and male connector on the other side, can be connected to the receiving set and steering engine.
Package includes: 20 pieces of female to male servo extension cable wires with 4 different lengths, enough for you to use on different occasions.

Check Stock

Que-T Brass Steering Servo Horn Arms 3.1/4.1/5.1mm for RC Car Boat Rudder Parts (Brass, 4.1mm)

Suitable--The servo arm is suitable for EMAX ES08MA II/ES08MD II Servo (For Axial SCX24 Crawler)..
High Quality--Our rc servo arm is made of aluminum alloy material, not easy to corrode, construct for precision and durability..
High Precision--CNC machining makes it precise in size and stable in performance..
RC Servo Bracket--This servo arm comes with a servo bracket, which is made of high quality aluminum, anodized and durable..
What You can Get--A rc servo arm with some screws, easy to install, and a rc servo bracket..

Check Stock