Top Pwm Servo Driver Reviews

ZOSKAY 1X DS3218 Update servo 20KG Full Metal Gear Digital servo Baja servo Waterproof servo for Baja Cars(Control Angle 180)

DS3218 20KG Large Torque Digital Servo with precision potentiometers,stable,low noise,waterproof: IP66.
High-precision metal gears with hard anodizing, CNC aluminium middle Shell, Dual ball bearings.
Large Torque&speed – 18.5kg.cm (0.16S/ 60°)@5V,maximum 21.5 kg.cm (0.14S/60°)@6.8V Operating travel:180°（PWM 500-2500μs）.
High performance digital standard servo for any crawler.
and for robot joint activities,TRX 4 Traxxas， SMT10 Mega Truck， SCX10 II，ARRMA Nero 1/8…..
Package Included: 1 x Digital Servo 1.58x0.79x1.60inch (40x20x40.5mm).
Weight: 60g (2.12oz) 1 x 25T Adjustable metal servo arm.

Check Stock

HiLetgo 5pcs Nano I/O Expansion Sensor Shield for Arduino UNO R1 Nano 3.0 Duemilanove 2009

14 I/O Pin (servo type with GND, power and signal).

Check Stock

Nema23 2N.m 57 Hybrid Closed Loop Servo Stepper Motor 2Nm 76mm+HSS57 Servo Driver Controller CNC Kit 24-50V DC For CNC Router Engraving Milling Machine

Name:Nema23 2N.M Servo Motor Driver CNC Kit.
Servo Driver:HSS57 2-Phase Hybrid Stepper Servo Driver.
The torque reducing is much lower than open loop stepper motor when it is at higher speed.The high speed performance and torque are enhanced in a....

Check Stock

Large Current 50A H-Bridge High-Power Single-Channel Motor Driver Module Semiconductor Refrigeration

【H-bridge Driver Module】The drive uses a full H-bridge driver module full-bridge MOSFET driver chip and composed with very low internal resistance and high current. MOSFET H-bridge driver circuit, with strong drive and braking effect, signal isolation chip isolates motor drive effectively..
【Effective Protection】With the microcontroller PWM signal isolation, effectively protect microcontroller..
【Input Maximum】To achieve the motor forward and reverse rotation, two PWM input maximum 200kHz frequency..
【Fully Compatible】Power indicator is schematically clear. The power supply voltage 5V to 15V. 3.3V to 12V, PWM level is fully compatible. High current 50A..
【Warm Tips】Ffor your safety and protection of use, our product is tested to ensure trouble-free installation and performance, please rest assured to buy..

Check Stock

AEDIKO MG996R Servo Motor Control 180 Angle Metal Gear Servo Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter 2-Pack (MG996)

Positioning Speed Without Load: 0.17s / 60 degrees 4.8V.
Compliant with Futaba, Hitec, Sanwa, GWS, etc ..
Latest Version: MG996R Servo Motor Which Updated from SG90 and MG90S Micro Servo Motor,Made of High Precision Potentiometer and High Resolution Digital Chip to Ensure Stable Performance and Solve Problems:Unsuitable R / C and Slow Response Time.
Gear Type: All Metal Gear RC Servo Can Control the Angle Range from 0 to 180, with Precise Control and Gears are Consistent,Which Can Rotate 360 Degrees When Power Off.
Application: Analog Servo Motor Great for RC Helicopters, Micro Robots,Robotic Arms and RC Rock Crawler, RC Boat Motor,Truck, Boat, Racing Car,Various Remote Control Toys and Arduino Experiments.

Check Stock

PWM Pulse Generator, DROK Dual Mode Adjustable Function Generator DC 3.3-30V 1-150kHZ 1-9999 Variable Pulse Width Frequency Duty Cycle Square Rectangular Wave Signal Generator Module with Case

PARAMETER — working voltage DC 3.3-30V.
DUAL MODE — the signal generator has 2 modes, PWM mode (default) & pulse mode..
APPLICATION — the signal generator module can be used to generate square wave rectangular wave signals for controlling DC motors or stepper motor driver.
for servo motors, stepper motors, electric jaws, PLC pulses replacement, etc..
PROTECTION — with anti-reverse protection, 5.08mm terminal wiring..
EASY TO OPERATE — the signal generator can control start or stop, it can also connect the external switch to control the output signal ON/OFF..

Check Stock

Yahboom RC Servo Tester 1 8 16 Channels Servo Motors Controller Centering Tool with Over-Current Protection, 2 Control Modes (Servo Tester 8 chan)

8-channel independent servo interface and 8 high-precision potentiometers..
Support manual mode,centering mode,which can be switched by function keys.
Terminal block （5-8.4V）power supply port,with Over-Current Protection. Compatible with any 5V-8.4V servos..
Control accuracy: 0.09 degrees(PWM limit small change value 1us).
Wide range of applications.No need any codes, servo can be controlled by buttons or the adjustable knobs..

Check Stock

AEDIKO MG995 Servo Motor Control 180 Angle Metal Gear Servo 20KG Digital High Speed Torque Servo Motor for Smart Car Robot Boat RC Helicopter 2-Pack (MG995)

Positioning Speed Without Load: 0.17s / 60 degrees 4.8V.
Compliant with Futaba, Hitec, Sanwa, GWS, etc ..
Latest Version: Micro Servo Made of High Precision Potentiometer and High Resolution Digital Chip to Ensure Stable Performance and Solve Problems:Unsuitable R / C and Slow Response Time.
Gear Type: All Metal Gear RC Servo Can Control the Angle Range from 0 to 180, with Precise Control and Gears are Consistent,Which Can Rotate 360 Degrees When Power Off.
Application: Analog Servo Motor Great for RC Helicopters, Micro Robots,Robotic Arms and RC Rock Crawler, RC Boat Motor,Truck, Boat, Racing Car,Various Remote Control Toys.

Check Stock

HiLetgo BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

5V isolate with MCU, and effectively protect MCU.
Voltage indication of motor driver output end.
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
isolation chip 5 V power supply (can share with MCU 5 V)..
Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
two heat flow passing through an error signal output..
Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.

Check Stock

Nema24 3N.m Closed Loop Stepper Servo Motor 88mm 5A+HSS60 Hybrid Driver CNC Kit for CNC Router Engrvaving Milling Machine

Servo Driver:HSS60 2-Phase Hybrid Stepper Servo Driver.

Check Stock

6 Axis 125KHz NVCM USB Mach3 Stepper Motor Motion Control Card Breakout Board USB interface CNC Controller Board 12-32VDC for Servo Motor

♞【Support software】This NVCM card support Mach3 software, through USB port to communicate with computer..
♞【DC power supply input】main device is 12V-32V DC power supply input,current should higher than 1A.
♞【Max 6 Axis Control】Can support 6 axis stepper systems maxisim,125KHz pulse output for every axis.
♞【PWM output】1 port 0-10V spindle speed analog output interface(can change to PWM output).
♞【Multifunction】 Power supply interface, USB connection interface, Stepper/Servo control output interface, spindle control output interface,....

Check Stock

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..

Check Stock

JUKI MO-6714S Industrial 4-Thread Overlock Sewing Machine

✅Thank you! see below full info. on this machine,--- Get your sewing job done real fast with the Juki DDL-8700H sewing machine that can do up to 5500 stitches per minute. This Juki sewing machine has a large 11-inch arm space that lets you work with even large quilts. The stitch length of this 5500 SPM sewing machine goes up to 5mm which gives you a lot of freedom in doing your job..
✅The sewing machine complies with the "Juki Group Green Procurement Guidelines" on the use of hazardous substances, will be delivered in 3 boxes. 1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.
✅1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.

Check Stock