Top Pressure Meter Series Reviews

MESR-100 Capacitor Tester, Geevorks ESR Meter in Circuit Capacitor Tester Up to 0.001-100.0R, Auto-Ranging Ohm Meter

  • This MESR-100 auto-ranging capacitor ESR and low Ohm meter measuring range from 0.001 to 100.0R, support in circuit testing..
  • Capacitance meter is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C).The impedance become small, and we can then measure the true series resistor value..
  • Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a r-esult we can use it as in circuit test..
  • Dual terminal, for fast and easy inspect internal resistance of the capacitor, a printed ESR table for fast check..
  • Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.[Note: without SMD test clips].
Check Stock

MOTOR METER RACING Electrical 6 Gauge Set - 3-3/8\ 85mm Electrical Speedometer & Tachometer - 2-1/16\ 52mm Voltage, Fuel Level, Water Temperature & Oil Pressure - Black Dial - White Needle

  • MOTOR METER RACING Classic Series 6 Gauge Kit is Designed for Vintage Style, Features the 6 Most Essential Gauges for Any Car or Truck's Instrument Cluster - Includes Speedometer & Tachometer - Voltage, Fuel Level, Water Temperature, Oil Pressure.
  • Fits any 1 to 9 Cylinder Gas Powered Engine & 12-Volt Negative Ground Vehicle. Works with ECU Signal - Black Dial - 316 Stainless Bezel - White Light bulb Illumination - Convex Lens & White Needle.
  • Speedometer Readings from 0 to 140 MPH, Tachometer Readings from 0 to 8000 RPM, Volt Readings from 8 to 16V, Fuel Level Readings from E, 1/2, F, Water Temperature Readings from 100° to 250°F, Oil Pressure Readings from 0 to 100 PSI.
  • Package Includes 2' Speedometer Power Harness, 2' Tachometer Power Harness, Water Temp Sensor (1/8 NPT), Oil Pressure Sensor (1/8 NPT), Fuel Level Sender, U-bracket kit & Installation Instructions.
  • One-year Limited Warranty & Free Lifetime Technical Support.
Check Stock

Soda Machine Adapter Hose Kit Direct Connect to Soda Water Make Machine

  • Allows to use a standard CGA-320 large CO2 tank in most soda machines. Works with most soda machines and allows normal operation without any permanent changes.(not suitable for Terra series).
  • Save money on the refill. This system allows you to connect your soda machine to CG320 co2 tank.Outlet Valve, like 5lb, 20LB or 50lb commercial CO2 tanks..
  • DN3 6mm Microbore Hose length 5ft(1.5 meter), high pressure hose,very soft,not easy to fold break. The hose material is food-grade materials, which is no odour..
  • Suitable CGA320 Valve of CO2 Tank (USA, CAN, Brazil, Colombia, Philippines...).Tips: this soda water accessory can not work with RPV-value(residual pressure value), please check your CO2 value before purchase..
  • Light weight and Easy to Install, this soda co2 cartridges adapter is 60 inches long and the weight is sonly about 0.33kg,compared to other heavy ones,this one is more suitable for quick installation..
Check Stock

testo 510 Digital Manometer I Dual-Port Differential Pressure Meter for air Conditioning Systems and Ventilation ducts

  • Versatile: The testo 510 measures differential pressure, total external static pressure, manifold pressure and duct velocities, making it ideal for HVAC/R field servicing technicians.
  • Precise measurements: Thanks to the temperature and air density compensated pressure sensor, the air pressure meter delivers accurate data for ten different measurement units.
  • Always ready: The backlist display, in conjunction with its intuitive design and magnets on the back, allow for a convenient application of the compact digital pressure gauge.
  • Durable: Equipped with a particularly rugged housing, including a protective cap and a battery life of 50 hours, the gas pressure meter offers a reliable performance.
  • Easy operation: The compact, lightweight pressure measurement device comes with a belt pouch, two hoses and a wrist strap and thus can easily be taken to any job site.
Check Stock

co2CREA Hard Case Replacement for Omron 3 Series Omron M2 Classic Upper Arm Blood Pressure Monitor BP7100 BP710N HEM-7120 Hem-7121 HEM-7124

  • co2CREA hard travel case replacement for OMRON Bronze Blood Pressure Monitor BP5100 or Omron 3 series BP7100 Omron BP710N upper arm blood pressure monitor or Omron M2 upper arm Omron blood pressure monitor wireless HEM-7120 Hem-7121 HEM-7124. Hard EVA shell case is shockproof dustproof and water resistance, protect your Omron 3 series Omron Bronze blood pressure monitor Omron blood pressure monitor upper arm from drops, scratches, bumps, splash, and dust..
  • This blood pressure monitor Omron blood pressure cuff protection case perfect for your Omron series 3 blood pressure monitor Omron blood pressure machine upper arm blood pressure monitor, This Omron Bronze blood pressure monitor case has more space to accommodate the Omron series 3 blood pressure cuff arm Omron 3 series upper arm blood pressure monitor Omron blood pressure machine Omron arm Omron series 3 blood pressure monitor bp cuff and more accessories..
  • co2CREA hard travel Omron 3 series upper arm blood pressure monitor digital blood pressure monitor upper arm case is a build-in super quality lining reflects superior taste and ensures a long-lasting performance, the soft anti static lining can protect your Omron blood pressure monitor' series 3 Omron blood pressure monitors blood press....
Check Stock

IDEAL INDUSTRIES INC. 61-686 Digital Light Meter with Remote Sensor, Measure All Visible Light Sources

  • ACCURATE LIGHT METER: Measures light levels from fluorescent, metal halide, high-pressure sodium, incandescent, and LED light sources. The perfect “must-have” instrument for basic lighting audits to address safety, productivity and energy efficient needs..
  • MEASURES ALL VISIBLE LIGHT SOURCES: The 61-686 meter measures visible light from LED, fluorescent, metal halide, high-pressure sodium, incandescent and other light sources. Measures in four ranges up to 20,000 Foot Candles or 200,000 Lux..
  • AUTO SHUT OFF: To extend the life of your battery, the unit will automatically power off after 10 minutes of non-use. Also features a convenient low battery indicator so that you can ensure that your Digital Multi-Meter is always charged and ready to use..
  • TETHERED SENSOR: Tethered remote sensor with 59 in. (1.5m) cable for remote measurements..
  • PRODUCT DETAILS: Weighs approx. 8.8 oz. (250 g) with battery. 2000 count LCD display. Includes IDEAL Electrical 61-686 Digital Light Meter, User’s manual, carrying case and 9V battery. +/- 3% basic accuracy..
Check Stock

Manometer, 12 Selectable Units Differential Pressure Gauge, Dual-Port Manometer Gas Pressure Tester, Digital Pressure Gauge with Backlight, Professional Air Pressure Meter, Handheld HVAC Manometer

  • 【Portable Manometer with ABS Material and LCD Display】The handheld digital pressure gauge is made of ABS material, and the excellent performance of high-temperature resistance and impact resistance makes the air pressure meter have a long service life. 4.45CM×4.95CM display, support LCD backlight, convenient lighting operation, display data clearer and easier to read..
  • 【Multifunctional Pressure Gauge with Accurate Readings】The digital pressure gauge adopts a high-quality pressure sensor, which has the characteristics of high precision and wide range. High-precision ADC and low-power MCU. Maximum/minimum mode and DIF mode. Professional air pressure gauges are specially used for gas measurement and calibration, gas pressure system troubleshooting, laboratory testing, maintenance and installation of blowers, clean rooms, boilers and other gas appliances..
  • 【Differential Pressure Gauge with 12 Selectable Units】The length of the two hoses in the gas pressure gauge set is 25cm.
  • The thread size of the barb metal connector is 1/8 inch.
  • 12 optional units (mmHg, inHg, ftH₂O, cmH₂O, inH₂O, Pa, KPa, mbar, bar, psi, Kgcm² and ozin²).
  • 【Manometer for Measuring Positive and Negative Pressure】There are two ports on the top of the differentia....
Check Stock

PROWELD Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Welding Accessory for Welding Machine

  • PROWELD Argon / CO2 Regulator and Flow Meter is a pressure reduction equipment to reduce the pressure of cylinder holding various kind of gas under....
  • Outlet of the Flowmeter will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting. It comes with a standard 1/4" barbed fitting..
  • Can retain steady pressure output even the input pressure and input flux changes. Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated....
  • Argon flow meter's body is made of high-quality brass, which can withstand harsh environments..
  • Majorly used for welding,slicing,chemical industry,analyzing,testing and other industry usage..
Check Stock

LC200A Inductance Inductor Capacitance Capacitor L/C Multimeter Meter Tester

  • This MESR-100 V2 auto-ranging capacitor ESR and low Ohm meter measuring range is 0.001-100.0R, support in circuit testing..
  • It is the series resistance inside the capacitor, and 100kHz is used to remove the impedance 1/(2*pi*F*C). When the impedance becomes smaller, the real series resistance value can be measured to determine whether the capacitor is bad/damaged or in good condition..
  • Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test..
  • During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.【Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.】.
  • Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check.Equipped with a SMD alligator clip for more accurately testing..
Check Stock

BTMETER Digital Anemometer Barometer Handheld, for Wind Speed Temperature Wind Chill Tester w/Humidity, Altitude, Barometric Pressure Meter for Climbing Drone HVAC CFM BT-100WM

  • ➤【MULTIFUNCTION ANEMOMETER】BT100WM wind speed gauge meter measures not only Wind Speed, Wind Temp, Wind Chill Indicator, but also Relative Humidity, Dew Point, Barometric Pressure and Altitude. With data log, Tripod hole for mounting, it’s ideal for outdoor activities:Long Range shooting, Hunting, Sailing, Kite flying, Drone Driving, CFM air flow test..
  • ➤【HIGH PRECISION】Digital wind meter for measure wind speed range 0.67 ~ 67.1 mph( +/- 5% accuracy).
  • Wind temperature range -10~45℃,14℉-113℉(+/-2 ℃/℉).
  • Wind meter measurement altitude from 0-19685 Ft. Resolution: 0.2 mph, 0.2℉,0.1% RH. So you can be rest assured to get fast and accurate reading..
  • ➤【EASY TO USE】Measures different readings such as Max, Min, Average, Current Wind Speed, display in 5 units: mph, ft/min, km/h, m/s or knots. Temperature (Celsius/Fahrenheit), Elevation(M, Ft), Atmospheric pressure(inHg, hpa mbar). And LCD backlit screen makes it easy to read in day or at night..
  • ➤【LOG THE BAROMETER DATA】This handheld wind speed meter can also log 16 groups of barometric pressure data for record, compare and analyse the relationship between temperature, humidity, and height. It’s compact pocket sized Pro anemometer for weather station, long distance shootin....
Check Stock

co2crea Hard Travel case Replacement for Omron 10 Series BP785N / BP786 / BP786N Upper Arm Blood Pressure Monitor Cuff

  • co2CREA hard travel case replacement for Omron 10 series wireless upper arm blood pressure monitor BP786 Omron 10 series wireless upper arm blood....
  • This blood pressure monitor Omron blood pressure cuff protection case perfect for your Omron series 10 blood pressure monitor Omron blood pressure....
  • co2CREA hard travel Omron 10 series bp monitor Omron blood pressure monitor BP785N upper arm case is a build-in super quality lining reflects superior....
  • This Omron 10 series blood pressure monitor case has a comfortable hand strap, so that the Omron 10 series upper arm blood pressure monitors Omron....
  • For sale is CASE ONLY! (Omron blood pressure monitors and Omron blood pressure monitor upper arm accessories are not included).
Check Stock

Diamond Original CR8900A Quad Band FM Mobile Antenna

  • The CR8900A is pretuned to give best bandwidth and VSWR over the FM portions of 10m, 6m, 2m, and 70cm ham bands when mounted on the side of vehicle (i.e. trunk lid) using a K400 or K600 series mount..
  • Designed specifically for the Yaesu FT-8900R.
  • The Diamond CR8900A quadband is a 10 meter, 6 meter, 2 meter and 440 MHz mobile antenna. It is a 1/4 wave on 10 and 6 meters providing and a 1/2 wave on 2 meters (2.15 dBi gain) and a 2 5/8 wave on 440 MHz (5.5 dBi gain). This antenna can handle up to 60 watts FM..
  • There are two center coils and a base coil. The connector type is UHF (for PO mount). The antenna is pretuned to give the best performance over the FM portions of the 10m, 6m, 2m and 70 cm bands when mounted on the side of the vehicle (such as a trunk lip mount). Suggested mounts would include the K400 or K600 series. This antenna is not recommended for a magnet mount or through-the-roof mounts. Includes an Allen wrench for tuning..
Check Stock

Auto Meter 7004 InVision Direct Fit Digital Dash LCD 73-87 Chevy/GMC Full Size Truck

  • ...ith 4 Switchable Colors (Red, Blue, White & Green). Equipped with Peak Recall and Warning Function to Guarantee Accurate Data and Road Safety.
  • SPEC.: (Speedometer & Tachometer): Standard 3-3/8" (85mm) Dial and 3-3/4" (95mm) Opening. (Water Temp, Volt, Oil Pressure & Fuel Gauge): Standard 2"(52mm) Dial 2-1/16"(52.4mm) Opening. EVO Gauge Set Requires any 1 to 9 Cylinder Engines Only - Compatible with 12-volt Negative Ground Systems.
  • Features: 4 Color Mode, 6 Level Brightness Adjustment.
  • 4 Types of Dimmer Setting where the Color Can be Shift According to Users' Needs in Different Conditions. It is Designed for In-dash Usage, While Suitable On-dash Mounting Cups Available to be Ordered - Flat Clear Acrylic Lens with Plastic Housing, Designed to be Installed with Ease.
  • Packaged: Speedometer GPS Sensor, Fuel Level Sender, Water Temp Sensor (Thread size: 1/8 NPT), Oil Pressure Sensor (Thread size: 1/8 NPT), 3-3/8" Mounting Stand (2 pcs), Daisy Chain, Wiring Harness, Installation Manual.
  • Warranty: One-year for Non-human Factor Damage and Free ....
Check Stock