Top Pcm Multiplexer Reviews

100PCS CD4053 CD4053B CD4053BE DIP-16 Analog Multiplexer IC

  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
Check Stock

Analog Multiplexer Single 8:1 ñ9 Volt 20 Volt 16-Pin Plastic DIP Tube

  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
Check Stock

Treedix TCA9548A I2C Multiplexer Breakout Board 8 Channel Expansion Board with pi Header for Arduino

  • The TCA9548A Breakout board supports communicating with multiple I2C devices with the same address, making it easy to interface with them..
  • TCA9548A multiplexer features: bidirectional eight-channel I2C multiplexer, active low reset input.
  • The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
  • In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
  • The chip is compatible with 3V and 5V and can be used with any logic level.
Check Stock

Installer CCTV 4CH Video Color Quad Multiplexer with Loopout Remote Control and Free 1 Amp Power Adapter

  • The 4Ch Video Color Quad Multiplexer allows several video signals from CCTV security cameras or other analog video devices to be combined and displayed on one monitor. The video processors are also commonly referred to as video mux, CCTV multiplexer, or color quad processor..
  • Full screen displays at real-time refresh rate for each channel. Multiple and automatic display by turn mode: 4Ch, 2Ch, Single Channel.
  • Camera title, time and date display for easy identification, 4 Channel BNC input and 2 Video BNC outputs.
  • Switch between NTSC and PAL system. Picture in Picture show, PIP position switched (top left, top right, bottom left, bottom right corner). High-Resolution Picture show, Adjust individual resolution. High-quality Screen Freeze function..
  • Free 1Amp Power Adapter and remote control Included.
Check Stock

OEM Nexperia 74HC4067PW,112, Analog Switch/Analog Multiplexer Single 16:1 24-Pin TSSOP Bulk (100 Items)

  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
Check Stock

Gustard R26 Discrete R2R DAC - R2R+1Bit XMOS DSD512 PCM768kHz LDAC Balanced K2 Clock Decoder with Remote Control(Sliver)

  • Dual architecture: Independent R2R 1Bit,support native PCM native DSD and DSD to PCM..
  • PCM NOS: Without any digital signal processing,bypassing the volume adjustment,raw PCM stream was decoded by the R2R array directly..
  • Native 1Bit DAC,support DSD 512 (via USB)and DSD 1024 (via IIS).The DSD stream decoded by the independent 1 bit convertor without DSD to PCM converting. *Volume is fixed under this mode..
  • Streamer/Renderer: Support roon,upnp and more protocols in the future..
  • Replace the input signal's clock with precision oscillators (local or external). Interference from the input source's clock is avoided..
Check Stock

Analog Demultiplexer, CD74HC4067 High Speed Analog Multiplexer Two-Way Connection Analog Multiplexer High Speed for Digital and Analog Signals

  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
Check Stock

10 PCS Analog Multiplexer,Breakout Board Module,CD74HC4067 High Speed CMOS 16-Channel Analog Digital Multiplexer Demultiplexer,Suitable for Digital and Analog Signals

  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
Check Stock

AITRIP 12PCS TCA9548A I2C IIC Multiplexer Breakout Board Module 8 Channel Expansion Development Board for Arduino

  • The TCA9548A adapter is connected to an I2C device with multiple identical addresses on the same I2C port on the main control board for normal communication and use.There are 8 I2C interfaces on one expander, and there are eight bidirectional transfer switches that can be controlled by I2C bus. This means that after 1 expander is transferred, 8 identical addresses can be connected to the same I2C port..
  • Expansion board TCA9548A compatible with IIC bus and system management bus (SMBus), active low reset input, support for hot insertion, low standby current, no glitch during power-up, support for voltages between 1.8V, 2.5V, 3.3V and 5V buses Level shifting, TCA9548A I2C IIC multiplexer breakout board depending on the contents of the programmable control registers, any single SCn/SDn channel or combination of channels can be selected..
  • 12pcs TCA9548A I2C IIC Multiplexer Breakout Board 8 Channel Expansion Board for Arduino.
Check Stock

Michigan Motorsports Knock Sensor Adapter for 1997-2004 LS1 LS6 Car to LS2 LS3 Knock Sensor

  • Knock Sensor Adapter for 1997-2004 LS1 Car to LS2 Knock Sensor.
  • This harness allows the dual-wire LS2 knock sensors located on side of the LS2 engine block to be plugged into the factory LS1 PCM harness. It has the perfect added length and thermal protection required to be routed near hot exhaust manifolds. Compatible with the PCM harness in LS1 Corvette and F-Body cars..
  • PLEASE NOTE THAT IN ORDER TO USE LS2 KNOCK SENSORS IN A LS1 CAR YOU REQUIRE SPECIAL LS1 PCM SOFTWARE CHANGES OR A LS2 PCM..
  • KEY FEATURES: Fully Plug and Play with the factory harness & sensors Military spec. high-temperature Teflon wire (same type used on oxygen sensors) 24" Length High-temperature (1200F) heat treated protective loom All connections crimped using our computerized crimp-quality monitoring system and then circuit checked for the utmost in reliability..
Check Stock

OREI Digital to Analog Audio Converter - Optical SPDIF/Coaxial to RCA L/R with 3.5mm Jack Support Headphone/Speaker Output DA21

  • Converts coaxial or optical digital audio input to analog stereo output over RCA and 3.5mm mini jack. Will not convert Dolby Digital Signal. Make sure to change to TV Output To PCM.
  • Supports all popular sample rates including 32kHz, 44.1kHz, 48kHz, 96kHz and 192kHz, at up to 24-bit resolution.
  • This Device will not convert Dolby Sound. It is only a converter not a Decoder. So make sure your device does not require Dolby conversion..
  • TROUBLE SHOOT - If your getting a Clicking Sound - Most likely your TV output is not set to PCM. Please change it PCM. Or if your getting Screeching or No Sound - Most likely you are trying to decode Dolby Sound to Analog. You will need a DA34 or DA34X.
  • INCLUDES DA21 Converter, Power supply, User Manual.
  • KINDLY NOTE : The DA21 will only support PCM audio output mode.It doesn't support Dolby, DTS, 5.1ch or 7.1 ch audio signals..
Check Stock

HiFi DAC+Sound Card Pifi DAC + PCM5122 DAC I2S Interface Analogue Output Signal Digital Audio Card Compatible with Raspberry Pi B + a + 2B Raspberry Pi 3B (64-bit)

  • Good performance: PCM5122 integrates a negative charge pump, and the output does not require a DC blocking capacitor.
  • very good ability to suppress noise in the frequency band. Since the load support is as low as 1K, PCM510xA can drive a variety of parallel products..
  • Ensure the continuity of signal impedance: Sound card Pifi DAC’s gold-plated RCV double clip and gold-plated 3.5 mm jack socket (recommended by amplifier). It is perfectly compatible with the official PI HAT size of the Raspberry Pi, based on the high gold plating process of the circuit board, and the arc line (high-end HIFI DAC adopts the arc line), which better guarantees the continuity of signal impedance and reduces signal reflection and refraction..
  • Pifi DAC + PCM5122 DAC: Pifi DAC + PCM5122 DAC, I2S interface, analog output signal, compatible with Raspberry Pi B + a + 2B Raspberry Pi 3B (64 bit). Provide infrared receiving interface..
  • Get rid of the current sound: The RPI+DAC HiFi kit uses an insulated power supply design to isolate the Raspberry Pi nutrition from the DAC part of the independent power supply, and the beads do not interfere with each other, and get rid of the sound of electric current. With this RPI+DAC HiFi kit, you can easily get m....
Check Stock

4K@60HZ HDMI Audio Extractor, HDMI 2.0b Audio Splitter Converter, HDMI to HDMI + Optical Toslink SPDIF + 3.5mm Stereo Audio with Control Output Analog Volume Knob Compatible for PS5/4/3/Blu-ray player

  • ... product is an HDMI extractor and HDMI splitter with control output analog volume knob, you can control HDMI extractor volume. Note: This unit does not support the ARC function..
  • 3 AUDIO MODE SETINGS- HDMI audio extractor splitter have Pass, 2.0CH, 5.1CH 3 kinds of audio mode options. 3.5mm audio output supports 2CH PCM LPCM stereo audio.
  • Optical SPDIF output supports 2CH PCM, 5.1CH Dobly Digital, Dobly TrueHD, DTS-HD, DTS.(Please set audio format on HDMI Source to PCM/ LPCM format to use If your device can't support these formats)PCM Setting Path: Device homepage -- system setting -- image and sound -- voice setting -- digital audio output -- PCM..
  • WIDE COMPATIBILITY- HDMI to Optical Audio Adapter suitable for various HDMI source devices to meet different needs. HDMI input: Blu-ray/ DVD/ HD player, cable/satellite box, Fire TV, Apple TV, PS3/PS4/PS5, Xbox, PC/laptop, HD camera, HD DVR etc. HDMI Output: Full HD TV, Monitor, Projector. Audio format: Speaker, Amplifier, Soundbar, D-o-l-b-y Digital, Dobly TrueHD, PCM 5.1/2.0.(Not suitable for passive speakers，An amplifier is required for use with this speaker).
Check Stock