Top Multi Function Stepper Reviews

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..

Check Stock

6Pcs L298N Motor Drive Controller Board DC Dual H-Bridge Stepper Motor Control and Drives Module for Arduino Micro:bit Smart Car Robot UNO MEGA R3 Mega2560

★L298N as main driver chip makes strong driving ability and strong anti-interference,dual-channel h-bridge driver working mode creates higher working efficiency,,drive stepper dc motors to work.to avoid damage the voltage stabilizing chip, please use an external 5v logic supply when using more than 12v.
★Dual-channel H-bridge driver working mode creates higher working efficiency..
★To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
★Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
★L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..

Check Stock

BIGTREETECH Direct Octopus V1.1 Silent 32 Bit Control Board 3D + TFT35 E3 V3.0 Two Mode Display Screen 3D Printer Parts for Creality Ender 3/5 CR10

【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to....
【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U....
【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard.....

Check Stock

18/4 AWG Shielded CNC Wire (50FT) — Flexible Stranded Shielded 18-Gauge 4-Conductor Cable for Stepper Motors, CNC Machines, NEMA Motors, VFD Spindles, CNC Routers, 3D Printers and more!

RESILIENT & FLEXIBLE: Stepper motor cable designed to bend smoothly in your CNC or 3D printer chain!.
SHIELDED 4 CONDUCTOR WIRE: Reduce interference for your CNC spindle motor or stepper motor driver!.
BEST RESULTS: Shielded wire means higher quality for your 3D Printer, CNC Machine or CNC Controller..
GREAT FOR All STEPPER MOTORS: Nema 17 Stepper Motor, Nema 23 Stepper Motor, Stepper Driver, & more!.
STEPPER MOTOR WIRE: The perfect upgrade to any CNC Kit, CNC Router Kit, or CNC Stepper Motor Kit..

Check Stock

BEOUZO Indoor Stair Stepper, Portable Home Gym for Women and Man, V-Type Sport Mode Climbing Machine, Cardio Fitness Stepper with LCD Monitor, Exercise Machine for Full-Body Workout

...raining thighs, hip and calves' muscle group. Unique V-Type stepping movement, moving up and down and side to side in a low-impact, which protects your joints. Also can directly strengthen deep muscles and not easy to cause acid accumulation in your body. If you have knee problem, please try exercises mildly.
Multi-function LCD MonitorA large LCD monitor displays Time, Row Count, Total Count and Calories.It's easier to track your fitness and progress. This LCD works on 1 AAA battery.
Double Hydraulic ResistanceUpgrade powerful load-bearing double hydraulic resistance rod strengthen the amount of exercise and keep stable while using this stepper machine.
Oversized Comfortable PedalsThe oversized PVC pedals promote blood circulation in the soles of the feet and do not slip down during exercise. Design with handle which could carry easily. The rubber stopper is for buffer,make the movement quieter.

Check Stock

C25S - Smooth Stepper Terminal Board

Full access to all the pins of the Smooth Stepper Board. Connects directly to the Smooth Stepper (from Warp9). The board is provided with sockets that allow the Smooth Stepper Board to be plugged directly into this board. No ribbon cables required. When using the Smooth Stepper board there is no need to use an additional power supply to power the board. It will draw power from the Smooth Stepper board. Built-in Passive Low Pass Filters for the all inputs..
C25 Smooth Stepper Breakout Board with push lock terminals.

Check Stock

Stepper Motor Mounting Bracket, 6pcs Steel Motor Mounting Nema17 Bracket, with Mounting Screws

Mounts are thick 2mm metal bent into an L shape. spot-welded 2 little triangle-shaped wedges in the corners. Ideal for replacement applications..
Stepper motor bracket durable alloy steel provides strong bearing pressure when printing..
Nema17 brackets are 2 long slots so you could easily loosen screws, tighten the belt tension of the motor and belt, and tighten them back down easily..
Stepper motor alloy steel mounting bracket can match standard Nema 17 stepper motor, and also include the mounting holes for Nema 17 economy planetary geared stepper motor but not for high precision planetary geared stepper motor..
6 pcs of NEMA 7 stepper motor mounting brackets, 90 degrees L-shaped bracket there are 4 holes drilled to mount for 3D Printer Motors Nema 17 Stepper Motor 42-40 Motor..

Check Stock

BIGTREETECH SKR V1.4 Turbo Control Board 32bit for 3D Printer Compatible with TFT35 E3 V3.0.1/TFT70 Touch Screen Support TMC2209/TMC2208/TMC5160/TMC2130 for Most FDM 3D Printer (with 5*TMC2209)

...ontrol board can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module.
in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY..
✨On-board TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap..
✨Compare to other stepper motor driver in the market, our TMC2209 silent stepper driver generate lower heat and it has a large-area cooling position to lower the temperature. It driver can lower 30% heat than others stepper motor drivers even working last for a long time. With Passive cooling on a 10 hours print, they only hit 37℃..
✨BIGTREETECH TMC2209 V1.2 is an ultra-silent motor driver IC for two-phase stepper motors, which adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque. spreadCycle allow for highly dynamic motion. Drive current 2A, peak current 2.8A, voltag....

Check Stock

Eiechip® CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver 3D Printer Interface & Driver Modules

3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module..
The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers..
It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors..
Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors..
This shield can make quick work for managing stepper motors in your project..

Check Stock

BIGTREETECH SKR PICO V1.0 Control Board: Mini Controller Board with TMC2209 UART Stepper Motor and Raspberry Pi Online Printing for Voron V0 V0.1 3D Printer Parts

【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V..
【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to realize Klipper Firmware and Raspberry Pi Online Printing..
【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion.
at the same time reserved WIFI interface, PT100 thermistor interface (optional, Only reserved interfaces, customers need to purchase chip welding, please pay attention.), dual Z-axis printer..
【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard. Supports “print from SD card” and “print via USB OTG” using the integrated USB-A port..

Check Stock

Creality 48CM TF to Micro SD TF Extension Cable Memory Card Adapter for/Raspberry Pi/Arduino GPS TV SDXC Creality CR10/10S/S4/S5/Ender 3/Ender 3 Pro Monoprice Select Mini 3D Printer

【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to....
【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U....
【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard.....

Check Stock

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
Terminal driver part of the supply area VMS: +5V ~ +35V.
Drive part of the peak current Io: 2A / Bridge.
Logical part of the terminal power supply range Vss :4.5-5 .5V.
Logical part of the operating current range: 0 ~ 36mA.
The control signal input voltage range: 4.5-5.5V low 0V high.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..

Check Stock

mxuteuk 2PCS 12V/24V DC Motor Speed Controller Switch Universal Electronic Stepless Speed Regulator Switch for Car Truck Fan Heater Control M-H-002

[Controller & Driver] Integrated step motor controller and driver functions.It can not only realize the drive motor, but also control the working state of the stepper motor in real time.
[Forward & Reverse] It can not only change rotation direction by pressing button, but also by potentiometer. It is also automatically change the direction through the selected working mode to achieve multi-scene and multi-application.
[4 Control Mode] In addition to its built-in parameters work mode,it can also control by external buttons or others driver or UART commands.
[9 work states] Built-in 9 default workflow programs, covering most applications, to meet the needs of different scenarios.Forward/Reverse/Delay/Loop/Self-locking/No-lock/Rotating speed and so on.
[HD LCD display] The HD LCD can clearly display the speed/delay/cycle times, making it easier to browse and set various parameters. Realize high-precision control of the motor. Parameters support memory function that will not be lost.

Check Stock