Top Micro Gear Motor Reviews

Adeept AD002 4 Pcs Compatible with MG90S 9G Micro Servo Motor, Metal Geared Micro Servo for RC Robot Car Helicopter Airplane Controls Boat Raspberry Pi Project

  • 【High Quality】100% new, good quality, AD002 Micro servo motor, Compatible with MG90 servo motor..
  • 【Full Metal Gear】 Metal gear with less noise,the metal gears help with the movement,these will rotate the proper direction..
  • Operating Speed: 0.11 seconds/60 degrees(4.8V).The servo Maximum angle is 180..
  • 【Wide Application】The great micro servo motors for helicopter/ boat / robot car / robot arm /remote controlled aircraft DIY. Fit for electronics DIY, compatible with Arduino, Raspberry Pi..
  • 【Service Guarantee】If you encounter any problems during use, please contact us, we will provide solutions to ensure your experience. We will reply within 24 hours.This AD002 servo motor is compatible with all Adeept robots..
Check Stock

Adeept AD002 2 Pcs Compatible with MG90S 9G Micro Servo Motor, Metal Geared Micro Servo for RC Robot Car Helicopter Airplane Controls Boat Raspberry Pi Project

  • 【High Quality】100% new, good quality, AD002 Micro servo motor, Compatible with MG90 servo motor..
  • 【Full Metal Gear】 Metal gear with less noise,the metal gears help with the movement,these will rotate the proper direction..
  • Operating Speed: 0.11 seconds/60 degrees(4.8V).The servo Maximum angle is 180..
  • 【Wide Application】The great micro servo motors for helicopter/ boat / robot car / robot arm /remote controlled aircraft DIY. Fit for electronics DIY, compatible with Arduino, Raspberry Pi..
  • 【Service Guarantee】If you encounter any problems during use, please contact us, we will provide solutions to ensure your experience. We will reply within 24 hours.This AD002 servo motor is compatible with all Adeept robots..
Check Stock

[4-Pack] MG996R 55g Metal Gear Torque Digital Servo Motor for Futaba JR RC Helicopter Car Boat Robot

  • This MG996R Servo motor which updated from SG90 and MG90S micro servo motor. (the Speed, Tension and Accuracy all increase).
  • The MG996R model compliant with most standard receiver connector,for Futaba, Hitec, Sanwa, GWS etc..
  • Power Supply: Through External Adapter. Stable and Shock Proof. Coreless Motor , Metal Gear ..
  • Torque at 6V 12kg/cm, 7.2V 13kg/cm.(Recommended voltage: 5V, current usage: 3A ). Positioning speed at 4.8V without load 0.17s / 60 degrees.
  • Universally Applicable: Micro Servo Motor for 1:10 RC car robot helicopter servo remote controlled aircraft and suitable for most DIY projects..
Check Stock

[2-Pack] MG996R 55g Metal Gear Torque Digital Servo Motor for Futaba JR RC Helicopter Car Boat Robot

  • The MG996R model compliant with most standard receiver connector,for Futaba, Hitec, Sanwa, GWS etc..
  • This MG996R Servo motor which updated from SG90 and MG90S micro servo motor. (the Speed, Tension and Accuracy all increase).
  • Power Supply: Through External Adapter. Stable and Shock Proof. Coreless Motor , Metal Gear ..
  • Torque at 6V 12kg/cm, 7.2V 13kg/cm.(Recommended voltage: 5V, current usage: 3A ). Positioning speed at 4.8V without load 0.17s / 60 degrees.
  • Universally Applicable: Micro Servo Motor for 1:10 RC car robot helicopter servo remote controlled aircraft and suitable for most DIY projects..
Check Stock

Micro Machines Playtronic MAX

  • Metal gear servo 9g is equivalent to the metal tooth plate of SG90. The installation size is slightly different from that of SG90. The servo system is more comfortable than cheap plastic gears..
  • Servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds but smaller..
  • This MG90S Micro Servo has metal gears for added strength and durability.It comes with a 3 horns (arms) and hardware..
  • The servo motors weight is 13.6g, suitable for 450 electric straight, swash plate steering gear, fixed-wing RC airplane..
  • The package included 6pcs MG90S Micro Servo, each MG90S come with one motor and three servo arms and three screws..
Check Stock

FOSA EMAX ES9051 4.3g Digital Micro Servo Plastic Gear 0.8kg Torque Servo RC Parts for 3D F3P RC Airplane, for FUT/JR Plug

  • Micro servo motor is designed for 3D F3P airplane. Easy to install and disassemble.
  • Digital micro servo is fast and precise to react, which can achieve the best control state when used with RC models.
  • Mini gear servo is high efficiency, low noise and low power consumption during operation.
  • Metal gear rc servo Gear is made of high-quality materials, very wear-resistant, light weight, can not be easily damaged.
  • Plastic gear is shock resistant and durable, practical, stable performance.
Check Stock

Bringsmart JGY-370 12V 10rpm DC Worm Gear Motor 12 Volt High Torque Engine Mini Turbine Worm 12V Reducer Electric Motor Self-locking for DIY Mini Geared Motor (JGY-370 12V 10rpm)

  • ALL-METAL GEARS, high-temperature resistance, high abrasion resistance, strong load capacity, sturdy and durable, effectively protect the turbo worm gear box motor body..
  • D SHAPED OUTPUT SHAFT, using high hardness steel, good toughness, impact resistance, the quality of the bearing and the service life of the turbo worm gear motor are improved, extremely durable.
  • GEAR DC MOTOR with MICRO-TURBINE WORM, you can change the wiring-connection to change motor rotation. Low noise and high torque..
  • Application: Label machines, remote control curtains, automatic voltage regulators, barbecue grills, ovens, washers, waste disposal machines, household appliances, coin machines, paper currency recognizers, automatic actuators, coffee machines, towel machines, printing machines and Stage lighting. This section is suitable for small motor configuration high speed ratio, the installation space is limited occasions, large torque output..
Check Stock

A/C adaptor S-8G -29 FOR S-8G 2.4GHz Extreme RC Helicopter

  • MG90S Micro Servo Motor, updated SG90 serve motor..
  • Operating Speed: 0.11 seconds / 60 degrees (4.8V).
  • Structural Material: Aluminum metal teeth, coreless motor, double ball bearin.
Check Stock

American Orthopaedic Cast Cutter, Replacement Blades Titanium Nitride Coated 2.5” (6.1cm)

  • SCOPE OF APPLICATION--This electic plaster saw is used for the removal of plaster bandage after fixed reduction, suitable for all types of plaster bandage, especially suitable for all types high polymer bandage..
  • OPERATORS SAFETY--Electric motor adopts double insulated protection device to ensure safety for the operators..
  • PATIENT SAFETY--The plaster saw uses micro motor with low noise, small vibration and speed adjust from large to small, in the actual test 1-5 gear, gently across the skin will not be injured..
  • OPERATION OF PLASTER REMOVAL--Set the machine to gear 5 or 6 and cut the surface of the plaster. The closer it is to the skin, the slower it should be, turn to low gear..
  • REPLACe BLADE--The blades of plaster saw are consumable, you can buy replacement blades from our shop..
Check Stock

MG90S 9g Servo Motor Micro Metal Gear for Robot Car Plane RC Helicopter Arduino

  • MG90S Micro Servo Motor, updated SG90 serve motor..
  • Operating Speed: 0.11 seconds / 60 degrees (4.8V).
  • Structural Material: Aluminum metal teeth, coreless motor, double ball bearin.
Check Stock

Milling on the Drill Press (DVD, 4 Hours)

  • ...3 axis.Headstock swivels 360 degrees.Max drilling diameter:0.9",Max Face screening capacity:2.5",Max vertical milling capacity:0.79",Distance from spindle to table:13.8",Spindle taper:MT3,Table size:27.5"x7.1".The speed display shows inch..
  • 【Micro-Feed Precision】Benchtop Milling Drilling Machine has a micro-feed function,the accuracy is up to 0.01'', only need to tighten the middle nut of the right hand wheel to achieve the micro-feed function, loosen the nut to achieve the manual up and down movement function.Integrated cross worktable,width is widened,with high precision positioning adjustment scale,which can be moved from front to back,left and right.It is important to note that this lathe has only a metric scale..
  • 【With MT3-ER32 Collect Chucks】Mini Mill Grinding machine comes with a set of MT3-ER32 milling chucks,without additional purchase.The size:4-3/5-4/6-5/8-7/10-9/12-11/14-13/16-15.Different sizes of chucks will meet your needs..
  • 【Digital Readout】Variable Speed Mini Milling/Drilling Machine USES an integrated spindle and brass gear,which makes it not only precise but also ....
Check Stock

Tilta Nucleus-Nano Wireless Lens/Focus Control System to Wirelessly Control The Focus of Most DSLR, Mirrorless, or Cine-Style Lenses on Cage, Gimbal Such As Ronin S

  • ... stops at close focus and infinity via the ability to set A-B limits on the Nano Hand Wheel Controller. Every motor has a 0.8 mod, which is the standard gear size for most cinema lenses. The torque of the Nucleus-Nano Motor at 5.5V is 0.65Nm and at 14.8V is 1Nm..
  • The motor has a 5-18V input tolerance for power via a Micro USB port. This allows the motor’s power to be drawn from the G2X tilt motor’s 5V Micro USB output or via a P-tap to 5V Micro USB cable (sold separately)..
  • The Nucleus-Nano uses a brand new state of the art power-efficient miniature motor. The Nano Motor features low noise and high torque. It can perform super fast focus pulls with silent precision! The built-in 15mm rod adapter allows for flexibility and compatibility with a wide range of camera rigs and professional mounting solutions..
  • The Nano Motor has its own built-in motor drive that communicates directly with the Nano Hand Wheel Controller. This negates the need to mount a separate MDR to your rig, allowing for a more compact camera setup and a quicker setup time. Simply set the Nano Motor and Nano Hand Wheel Controller to the same channel and you will have full control. The wireless range of both the Nano Hand Wheel Controller and Nano Motor is 300 feet!.
Check Stock

ZRM&E 4-Pack SG90 Mini Gear Micro Servo 9g Digital Spare Parts for Smart RC 450 Airplane Helicopter Car Vehicle Boat Models Fixed Wing

  • Type: 4 Packs SG90 9g Gear Micro Servo, Contains steering gear, rocker arm, screws, etc. all original accessories..
  • No Load Operating Speed: 0.12s/60degree (4.8V).
  • 0.10s/60degree (6.0V), Stall Torque: 1.6 kg.cm (4.8V), Dead Band Width: 5usec, Operation Voltage : 4.8V - 6V.
  • SG90 steering gear plastic gear, fast response, accurate angle, large torque, small internal resistance, smooth and delicate, not easy to get stuck..
  • Adopting ordinary micro motor, low pull force, recommend applying to ordinary small electric aircraft models, not recommended for use with larger fixed-wing and electric helicopters..
  • Ideal for fixed wing, helicopter, KT, fluttering, gliding, small robots, robots and other models. Recommend Model: Mini Car / Mini Ship / Helicopter & Airplane..
Check Stock