Top Maxline Nipple Fittings Reviews

Maxline Pressured Leak-Proof Easy to Install Air Compressor Accessories Kit Piping System | 1/2 inch x 100 feet HDPE-Aluminum | Connects w/ any Air Compressor Hose | 100 PSI | 35 Pieces | M3800.

of 1/2-inch tubing, (3) air outlet kits, compressor manifold kit, (5) elbow fittings, deburr and cutter tool.
175 psi maximum working pressure, 1/2-Inch inside diameter x 5/8-Inch outside diameter.
Compression style nickel plated brass fittings.
maximum from the air compressor, up to 2000 sq..

MaxLine Dual Outlet Port.Part Number: M8203.
This port has a 1" inlet that only works with 1" MaxLine tubing..
It features two 1/2" outlets that come out at an angle to make adding attachments convenient..
This outlet block also features a twist moisture drain on the bottom to help avoid excess water build up in your airlines..

MaxLINE 1" piping tee fitting Part Number M8012.
This MaxLINE Tee is specifically designed for the MaxLINE 1" tubing made by RapidAir and is great for adding extra tubing in multiple directions or adding extra air outlets..
This fitting is made of solid brass and has a double o-ring seal for a no leak connection..
It has split ring connections for easy disassembly if needed, and is rated for 175 PSI working pressure..
Solid Brass with Nickel Plating for Maximum Corrosion Resistance.

Reducer Adapter: Premium solid brass with thicker wall, more durable than iron and iron galvanized pipe fittings, 1/4" NPT male pipe x 3/8" NPT female....
Reducing Hex Nipple: Reducing hex nipple for connecting two threaded pipes with different diameters. Male National Pipe Taper (NPT) threads for....
Hex Bushing: Has a 3/8” male NPT threaded on one end and a 1/4” female NPT threaded on the other for connecting a female and a male pipe or....
These fittings are not allowed to be installed for potable water,NPT thread size does not actual diameter, it is only nominal pipe size..

3 Pack of the MaxLine M8067 Elbow Fitting for 3/4" Tubing.
Nickel plated brass fitting guards against corrosion.
Double O-ring compression style fitting, tubing can be removed from fitting if needed.

2 Pack of the MaxLine M8067 Elbow Fitting for 3/4" Tubing.
Nickel plated brass fitting guards against corrosion.
Double O-ring compression style fitting, tubing can be removed from fitting if needed.

1" MaxLINE compressed air piping 100ft tubing kit Part Number M6032.
This MaxLINE kit is a great solution for a compressed air piping system in a large garage/shop or a commercial application..
This is a high quality compressed air piping system..

Long nipple for connecting two threaded pipes and extending pipe length.
1/8" Male National Pipe Taper (NPT) threads for connecting to 1/8" female threaded pipes.
Legines pipe fittings are made of CA360 or CA377 brass, not ordinary copper alloy, and meet SAE standard, have dryseal threads, forgings & extruded..
Operating pressure of our fittings is up to 1200psi, more higher than other general fittings. Temperatures range from -53 to 121 degrees C (-65 to 250 degrees F).
These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..

This is a solid brass street elbow that features 1/2" male NPT threads on one side as well as 1/2" female NPT on the opposite side..
This part is produced by RapidAir for the 3/4" MaxLine air piping systems outlets to install an air coupler at a 45 degree angle, but can be used for other applications as well..
1/2" Threads Measure about 3/4" in diameter if measured with a tape measure..

【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
【Operating temperature range】Temperature rating: -65 to 250 degrees F.
【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..

【✔】High Quality Brass Grease Nipple Fittings Kit.
【✔】Set Includes 6 Most Used Sizes: M6, M8, M10, Straight, 45-Degree【 Please See Picture 2 for Specific Dimensional Size】.
【✔】Made of Good Quality Brass and are Hardened to Prevent Wear. Anti-corrosion and Durable.
【✔】Package Quantity: 106-Pieces, All of Product Will Be Packed in A Sturdy Transparent Plastic Case, Can Be Use for A Storage Box.
【✔】The Grease Zerk Nipple mouth is flat and smooth, great for fastening. The thread is deeply, thread pitch more sturdy, it will not slippery when rotating. Suitable for most automotive, motorcycle, truck, farm, and industrial applications..

This is a MaxLine M8203V dual outlet port with ball valve..
Features a 3/8" FNPT Port w/ Ball Valve (Serves as air pressure / moisture drain).
This port has a 1" inlet that only works with 1" MaxLine tubing..
It features two 1/2" outlets that come out at an angle to make adding attachments convenient..
This outlet block also features an inline ball valve to shut off the flow of air to the outlet as well as a twist moisture drain on the bottom to help avoid get excess water build up in your airlines. Dimensions: 3-7/8" Wide x 4-1/2" Tall x 3-1/4" Deep.