Top M1to M1adapters Reviews

Springfield Armory M1A Underlever Pellet Rifle Wood-Stock Air Rifle 0.22 Cal

  • PELLET AIR GUN: The M1A underlever spring-piston pellet rifle is a classic rendition of the M14. With a caliber of 0.177" or 0.22" and a barrel length....
  • QUALITY MATERIALS: Each underlever pellet gun features a wood stock for historic accuracy and a smooth finish. The single-shot pellet rifle has a....
  • UNDERLEVER ACTION: Our high-powered pellet rifle has an underlever design with the cocking lever located underneath the barrel. This pellet rifle has....
  • SAFE & SECURE LOADING: This pellet gun is a good choice for beginners. It features an anti-bear-trap safety mechanism that prevents the loading....
  • FIRING MECHANISM: Since the M1A is a pellet rifle gun, it fires pellets using a coiled spring. This powerful pellet gun has a high velocity of up to....
Check Stock

Case Club Springfield M1A Pre-Cut Waterproof Rifle Case with Accessory Box and Silica Gel to Help Prevent Gun Rust (Gen 2)

  • Pre-cut foam holds a single factory Springfield M1A Scout Squad, SOCOM 16, Standard, Loaded, National Match, Super Match, or Garand Rifle (Not meant to fit Springfield M1A CQB stock).
  • Holds up to six 10 round magazines, or three 20 round magazines & accommodates all major optics mounted either in the forward position or above the rear sight.
  • Stainless steel added to padlock points for added security, Orange peel texture added to exterior finish to minimize scratches, Structural ribs added to outside of case for increased durability, Front handle length increased to help counter balance off center weighted loads, Wide bodied snap latches that can be used with gloves.
  • Foam insert is (closed cell) high grade polyethylene which can be wiped clean.
  • Case is Airline Approved for checked luggage, padlockable, wheeled, fully shippable & dustproof.
Check Stock

Springfield Armory M1A Accessories CC5010

Check Stock

PETFAT Sadlak Industries M14/M1A Cleaning Drill Set

  • Sadlak Industries M14/M1A Light Duty Aluminum Front Rail.
  • Once the Front Rail is installed you have flexibility of attaching a clamp-on type Bi-Pod.
  • All hardware and screws have mil-spec. Manganese Phosphate finish..
Check Stock

Springfield M1A M14 Rifle Scope Mount

Check Stock

SPRINGFIELD ARMORY M1A Cleaning Kit

Check Stock

SADLAK M14/M1A Front Rail, Aluminum Low Profile Rail

  • Sadlak Industries M14/M1A Light Duty Aluminum Front Rail.
  • Once the Front Rail is installed you have flexibility of attaching a clamp-on type Bi-Pod.
  • All hardware and screws have mil-spec. Manganese Phosphate finish..
Check Stock

Guard Force Covert Strike

  • Specific units in Guard Force are tied to the four main building types:.
  • Barracks (soldiers, rangers, Stinger team, medic).
  • Motor Pool (Humvee, LAV, Fast Attack Vehicle, Bradley, M1A1, Paladin, MLRS, Demolition Vehicle, Patriot).
  • Rotary Air Center (Apache, Blackhawk, Transport Helicopter), and Fixed-Wing Center (Air Support Strike, Fighter and Stealth Bombers, Ground Attack Aircraft).
  • Two additional centers (Engineer and Technology) offer specialty units like M9 Ace Minelayers, Bunkers, Sandbags, Upgraded Stinger Crews, and Unmanned Air Vehicles..
Check Stock

BadAce M1A M14 Scope Mount Picatinny Rail Low-Profile

  • Centrally mounted and self-aligned to the bore.
  • Works on all M1A, USGI M14, and Norinco receivers.
  • No gunsmith required, easy installation in 20 minutes.
  • Low-profile design allows the scope to be mounted closer to the receiver.
Check Stock

Kensight M1A & M14 National Match Front Sight Springfield

  • High quality, drop-in replacement for the factory original unit.
  • Sight Body is wire-EDM machined from a Solid Billet of Chrome-Moly steel.
  • Traditional protective steel ears on either side of the front post.
  • M14 and M1A National Match front sight features a narrow 0.062" sight blade.
  • Backed by our Kensight Limited Lifetime Warranty.
Check Stock

New Locking Screw for M14/M1A Scope Mount

  • M1SURPLUS Brings You A Low Profile Scope Mount Rail For Springfiled M1A Rifles – Does “NOT” fit M14.
  • Provides a Picatinny Mounting Rail For Attaching Scopes or Optics.
  • Includes a Set of Low Height Aluminum Scope Ring Mounts.
  • Low Profile Design With See-Through Channel Allows Use of Your Rifles Iron Sights.
Check Stock

Sadlak Industries M14/M1A Heavy Duty Front Rail with Internal Nutplate for USGI Wood Stock

  • Fits: Springfield .308, M1A/M14, SOCOM 16.
  • One Free Aluminum opener(Randomly selected color,One Opener per Order).
Check Stock

NC Star AR10/M1A/FAL .308 Dual Magazine Pouch, Tan

  • MOLLE compatible .308/ 7.62X51 magazine pouch will hold two AR10, M1A/M14, FAL type magazines..
  • Perfect magazine pouch height for 7.62X51mm 20 round magazines..
  • Adjustable for magazine retention bungee cord with pull tab. Retention bungee cord is removeable from magazine pouch..
  • Metal drain grommet on the bottom of each magazine pouch..
Check Stock