Top Lvd Cutting Machine Reviews

Traxxas 3025 XL-5 HV Electronic Speed Control

  • ESC features 11.1V 3-cell LiPo compatibility and works with brushed motors only.
  • Fully waterproof design with Traxxas EZ-Set one-button setup and large, efficient heat sink.
  • Wide voltage latitude 6–7 cell NiMH (7.2–8.4V) and 2–3S LiPo (7.4–11.1V) with two stage low voltage protection (LVD).
  • Features five drive profiles including Trail Mode (forward / brake / reverse / with trail-tuned drag brake in neutral).
  • Special Crawl Mode features forward / instant reverse - no neutral with hill holding brake.
Check Stock

CZH-LABS Electronics-Salon 1PCS Low Voltage Disconnect Module LVD 12V 10A Protect/Prolong Battery Life.

  • Low Voltage Disconnect Module LVD, 12V 10A, Protect/Prolong Battery Life..
  • Suitable battery: 12V , Rated current: 10A..
  • Discount voltage: 10.0V , Reconnect voltage: 10.7V..
Check Stock

hynade CNC Blow Back Digital Air Plasma Cutter, Non-HF Pilot Arc Non-Touch Plasma Cutting Machine, THC Torch Height Control Enabled (CUT60DN)

  • Dual voltage plasma cutter :This is a 110/220V Non-HF Blow Back Pilot Arc Plasma Cutter, Input Power AC110/220V±15%,AC110/220V 55A cutting current with 60% duty cycle, 220V 55Amps 110V 35Amps Cutting Current.The working power range from 100V to 250V, Under 220V Pilot arc will not reliable if the voltage lower than 190V. Under 110V, the pilot arc will not reliable if the voltage lower than 100V.
  • Plasma cutter cutting thickness: Max Cutting Thickness 25mm@55A 220V 70PSI, Clean cutting thickness 20mm@55A 220V 70PSI, 12mm Clean Cutting thickness under 110V 60PSI. 63A power break, 45L/min Air compressor is suggested.
  • 2T/4T Function :Plasma cutting machine CUT60DN with 2T/4T function, also with Air/Cut Function, 2T 4T easy let the user operate machine and it is great help for the CNC cutting table. THC torch height control enabled. machine with function for torch protection, The LED light up if the torch connecting is not well, It will also lighting up while replacing the torch consumables,machine is not able to work while it lighting up.
  • CNC Plasma Cutting Machine : have 2 pins and 4 pins connecting port at rear of machine. 2 pins connector for The arc voltage output ratio 1:1, 4 pins connector for Signal Control.Easy works with CNC cutting table.The plasma....
Check Stock

Invisible Man

  • A small investment can make a huge improvement in the cutting performance of your machine.
  • Getting the best cutting performance from your Prestige Pro machine can be as simple as changing the PR standard cutting pad.
  • This PR Standard Cutting Pad measures 9 7/8" x 18"..
  • The many significant advantages of the extended length of this PVC vinyl Cutting Pad are an increased work surface, the ability to shuttle multiple dies through the machine for quicker cutting and for easy registration of ClearCrop Dies..
  • Cutting pads need replacement generally after 4-6 months.
Check Stock

Cuttlebug Cutting Plate B 6'X13'-

  • Can be used on an embossing cutting machine, the transparent durable cutting pad makes it easy to place materials for precise die-cutting..
  • Ensure both sides of the cutting pads are used, to help extend the life of your pads!.
  • The see-through PC plastic allows easy placement of materials for a precise die cut..
  • Allows complex graphics and complex patterns for die-cutting, suitable for small die-cutting machine, they are not suitable for large injection machine..
  • The clear acrylic die cutting plate is made of quality acrylic board, which is very suitable for your cutting and diy use, and it is very practical..
Check Stock

Monoprice 3-Feet HPDB68 LVD M/M SCSI Cable Screw (100779)

  • Monoprice brings you a wide assortment of classic SCSI (Small Computer System Interface) cables for your legacy storage devices.
  • SCSI was once the de facto standard for high performance systems due to it's faster transfer rates and versatility over the more standard ATA interface.
  • Unfortunately do to it's popularity and failure to standardize on a single connector type a wide variety of cable types exist.
  • We carry cables for many of the most popular configurations.
  • This is a Low Voltage Differential (LVD) cable with 68pin High Pitch D Subminiature HPDB68 connectors.
Check Stock

We-buys Cutting Dies C Plate Replacement Adapter Mat Clear 5.9'×7.6'

  • Can be used on an embossing cutting machine, the transparent durable cutting pad makes it easy to place materials for precise die-cutting.Plate thickness is 3mm.
  • Ensure both sides of the cutting pads are used, to help extend the life of your pads!.
  • The see-through PC plastic allows easy placement of materials for a precise die cut..
  • Allows complex graphics and complex patterns for die-cutting, suitable for small die-cutting machine, they are not suitable for large injection machine..
  • The clear acrylic die cutting plate is made of quality acrylic board, which is very suitable for your cutting and diy use, and it is very practical..
Check Stock

DONYER POWER 1500W Electrical Patio Heater, Ceiling Mounted, Outdoor or Indoor Use

  • ※ Real Fast：Rapid Heating get warm in 3 seconds..
  • ※ 2 Heating Modes ：① 600W low heating.
  • ※ Parameters：ΦA=42CM,2KGS,110-130V,50Hz,1500W, Heating scope: 65sq ft.
  • ※ Easy for installation：1m adjustable chain can disassemble and adjust the distance at any time and the most appropriate height for hanging is 70.9in to prevent children and pets from touching.
  • ※ For indoor and outdoor activities：Can be installed on indoor and outdoor ceilings, such as living room, garden, balcony, outdoor terrace and camping BBQ area；with ETL/CE/GS/LVD/EMC/IP24 certificate.
Check Stock

Monoprice SCSI Cable - 6 Feet - HPDB68 Low Voltage Differential Male/Male with Screw

  • Monoprice brings you a wide assortment of classic SCSI (Small Computer System Interface) cables for your legacy storage devices.
  • SCSI was once the de facto standard for high performance systems due to it's faster transfer rates and versatility over the more standard ATA interface.
  • Unfortunately do to it's popularity and failure to standardize on a single connector type a wide variety of cable types exist.
  • We carry cables for many of the most popular configurations.
  • This is a Low Voltage Differential (LVD) cable with 68pin High Pitch D Subminiature HPDB68 connectors.
Check Stock

DONYER POWER 1500W Electrical Patio Heater, Ceiling Mounted, Outdoor or Indoor Use

  • ※ Real Fast：Rapid Heating get warm in 3 seconds..
  • ※ 2 Heating Modes ：① 600W low heating.
  • ※ Parameters：ΦA=42CM,2.7KGS,110-130V,50Hz,1500W, Heating scope: 65sq ft.
  • ※ Easy for installation：1m adjustable chain can disassemble and adjust the distance at any time and the most appropriate height for hanging is 70.9in to prevent children and pets from touching.
  • ※ For indoor and outdoor activities：Can be installed on indoor and outdoor ceilings, such as living room, garden, balcony, outdoor terrace and camping BBQ area；with ETL/CE/GS/LVD/EMC/IP24 certificate.
Check Stock

CZH-LABS LVD Low Voltage Disconnect Module 12V / 30Amp

  • Operating Voltage: DC 6 to 18V, Rated current: 30 Amp..
  • To protect electronics from damaging low voltages and prevent a deep discharge of a battery during an extended power outage, the LVD module will....
  • Programmable voltage setting for Disconnect and Reconnect (rocker switch set to AUTO). With emergency ON or OFF function, if you want switch output to....
  • Set rocker switch to AUTO, when the battery voltage drops to less than or equal Disconnect Value and continuously held for 5 seconds, load switch will....
  • Based on Microcontroller and MOSFET (on status resistance < 0.003 ohm), more precise voltage, smart and long life switch output. Green-red dual color....
Check Stock

OKVEQUIP 3PCS 4Inch Super Thin Diamond Saw Blade Dry or Wet Tile Ceramic Disc Wheel Porcelain Cutting Discs for Marble Quartz Granite

  • 【Tile Blade Widely Use】: Ceramic tile blade cutting discs can cut porcelain, vitrified tiles, ceramic tiles and thinner granite, marble, etc. quickly and accurately..
  • 【Features】: Diamond tile blade fast cutting, small kerf, low power consumption, sharp and wear-resistant,using hot pressing sintering process, can be used for a long time.
  • 【Applicable type】：Concrete cutting machine saw blade can be used for dry/wet cutting.
  • 【Adapted machine】: Cutting marble granite porcelain tile can be used with marble machine, desktop cutting machine, angle grinder.
  • 【Ceramic cutting disc wheel parameters】: size 105x20x10MM, outer diameter 105MM, inner diameter 20MM, with washer to change 16MM, thickness 1.2MM, RPM2000-8000.
Check Stock

Herocut Plasma Cutter, 35Amp Plasma Cutting Machine, HF 50/60Hz Invert Technology Plasma Cutter, Max Cutting Thickness 8mm (CUT35 110V)

  • ✤ Plasma Cutter, 110V 35A cutting machine with IGBT inverter technology, It is long life and efficient higher than mosfet machine..
  • ✤ Very good to cut car flame, Clean cutting thickness 6mm Max cutting thickness 8mm in 110V 60PSI Machine only work in 110V not 220V, Please confirm the voltage before buying this machine. Machine maybe explode if connect it to 220V, Be careful~!.
  • ✤ This plasma cutter with current display and air gauge fixed on panel, Easy read air pressure and current, these functions are great to help the user cut any metal..
  • ✤ The plasma cutter easy to cut stainless steel, Alloy steel, mild steel, Copper etc. Quality cutting torch PT31 come with machine, Max cutting thickness is 10mm at 40Amps 110V 60PSI..
  • ✤ Machine come with 110V power plug, We provide three years warranty for this unit..
Check Stock