Top Low Temperature Pipes Reviews

Electric Water Pipe Heating Cable with Thermostat for Pipe Freeze Protection, 6ft 120V Snow De-Icing Cable with Build in Thermostat, Pipe Warmer, Heat Pipe Tape - CSA/ETL Listed

  • ✅ 003cb003e[100% Money-Back Guarantee] 003c/b003e--Customer satisfaction is our priority. If for any reason you're not completely satisfied, you can ask for a replacement or full refund, no questions asked. Buy with confidence!.
  • ✅ [High quality]--UL, ETL and CSA certified,more safer to use.Industrial grade heat shrinkage tube for connection.Each Cable consists of tough XLPE inner insulation, AL foil, a continuous ground braid as well as weather and non-supportive climatic conditions resistant PVC (high-low temperature) outer coating. Can convert 100% of electrical energy into heat without energy loss..
  • ✅ [Note]--Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight. If the ambient temperature is lower than -20°F(-29°C), please use 1" thick insulation material..
  • ✅ [Application]--Suitable for use on water filled plastic ((including PEX)and metal water pipes(including copper, galvanized, ABS plastic, PVC plastic pipes, etc).Not use for empty water pipes, fuel lines, hoses, gutters, steam lines and so on.Keeps water flowing down to -40℃..
Check Stock

XAREX RPH 120V 12ft, Pipe Heat Cable with Glass Tape, Self-Regulating Pre-assembled Heat Tape with 6ft Cord & Lighted Plug for Freeze Protection of Plastic and Metal Water Pipes Electrical Heat Trace

  • QUALITY HEAT CABLE - Keeping your pipes/water lines from freezing during the winter,functioning perfectly for all kinds of plastic and metal pipes (including copper, galvanized, ABS plastic, PVC plastic pipes, etc), not suitable for gutters, hoses.
  • SELF-REGULATING TECHNOLOGY - the cable output will change automatically depend on the ambient temperature, the output goes up when the temp is low and goes down when it's high, saving energy and electricity for you, illuminated plug lets you see if the heat cable is working from a distance.
  • BUILD-IN THERMOSTAT - you just tape the thermostat in place against the pipe, the cable is able to monitor the temp of your pipes, it will work when the temperature of the pipe below 37°F and turn off when above 50°F, 1.75 away from the plug.
  • EASY TO INSTALL - pre-assembled for quick installation, the heat cable can be straight-traced or spiral on the pipe, be aware that the lowest installation temperature is 14°F and the maximum exposure temperature is 221°F.
  • HEAVY DUTY AND SAFECABLE - ETL cerfied, 2FT cold lead and 3FT/18FT heat cable is commercial grade for long-time and heavy-duty usages, PVC out jacket, 3W/ft under 50°F, 1 Year warranty provided, please test the cable before the installation.
Check Stock

HEATIT JHSF 60-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

HEATIT JHSF 120-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

  • JHSF doesn't work unless the ambient temperature is below 37F/3 degree C. Please test the cable in a cold environment..
  • Suitable for use on plastic and metal water pipes.( including inlet pipe,drain pipe, sewer , palm tree frost protection etc). Self regulating heating cable output will adjust automatically based on the ambient temperature at each point along the cable..
  • Pre-assembled, easy to install. Including grounded plug with light, built in thermostat(turn the cable 37F on 50F off) and instructions. 120 volt, 3 watts/ft at 50 degrees F. Protect pipes up to 2" in diameter. Can be used by straight, spiral and overlap..
  • ETL approved. 2 ft 18/3 cold lead with plug. The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable. Normally you can feel the slight warm on the heating cable in few minutes..
Check Stock

H&G lifestyles Roof Snow De-Icing Heating Cable Self-Regulating-Plug-in Ready Heat Cable 80 feet 8 Watts Per Foot

  • ROOF HEAT CABLE - Keeping your pipe/water lines/roofs/gutters from freezing during the winter,functioning perfectly for plastic and metal pipes, all kinds of roofs, keep the water flowing in gutters.
  • SELF-REGULATING TECHNOLOGY - the cable output will change automatically depend on the ambient temperature, the output goes up when the temp is low and goes down when it's high, saving energy and electricity for you, illuminated plug lets you see if the heat cable is working from a distance.
  • HEAVY DUTY CABLE - 6FT cold lead and 6FT/18FT heat cable is commercial grade for long-time and heavy-duty usages, PVA out jacket, 5W/ft under 50°F for heating pipes.
  • EASY TO INSTALL - pre-assembled for quick installation, the heat cable can be straight-traced or spiral on the pipe, be aware that the lowest installation temperature is 14°F and the maximum exposure temperature is 221°F.
  • RELIABLE FOR HEATING PIPES - UL and ETL cerfied, illuminated plug lets you see if the heat cable is working from a distance, please test the cable before the installation, 1 Year warranty provided.
Check Stock

HEATIT HISD 18-feet Pipe Heating Cable with Built-in Thermostat

  • ...all and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 15-feet Pipe Heating Cable with Built-in Thermostat

  • ...all and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 12-feet Pipe Heating with Built-in Thermostat, Black

  • ... in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 3-feet Pipe Heating with Built-in Thermostat, Black

  • ... in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

10mm x 10mm Length 1M Black Plastic Open Type Cable Wire Carrier Drag Chain Towline R18 for 3D Printer and CNC Machines

  • The Cable Drag Chain is easy to install and repair, free movement, low noise, wear-resistant, high-speed movement.
  • You can link the cables with each other to form one long length you need.
  • Surface gloss,Low temperature resistance, wear resistance and corrosion resistance.
  • Suitable for reciprocating motion in occasions, with built-in cables, pipes, water pipes, etc.
  • The Drag chain has been widely used in CNC machine tools,electronic equipments, fire machinery, stone machinery, glass machinery, doors and windows machinery, counting devices, electrical machines, etc.
Check Stock

DEWENWILS Roof Heat Cable, 6ft Heat Tape for Pipe, Gutter, Roof, Self-Regulating Cable Pre-Assembled, UL Listed

  • ...tall and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

Qmark WHT500 Utility Heater for Use in Well Houses, Utility Rooms, and Areas with Pipes and Machinery, 500 Watt, 240 Volt, Beige

  • ...tall and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

Closed Cell pipe Insulation, High Density Antifreeze Tubular Insulation, Air Conditioning Water Insulation Tubing, Suitable for Outdoor, Bathroom, Factory, Wall Thic

  • 1. Product material: Use excellent performance polyethylene rubber and polyethylene as the main raw materials, closed-cell foam structure, weatherproof and high temperature resistance. Rubber and plastic materials have high elasticity..
  • 2. Product characteristics: soft, flex-resistant, cold-resistant, high-temperature resistant, flame-retardant, waterproof,.
  • Low thermal conductivity, shock absorption, sound absorption and other properties.
  • 3. Product size: each tube is 1.9 meters long, inner diameter 25mm/0.98in, 32mm/1.26in, 43mm/1.69in, 48mm/1.89in, 60mm/2.36in, 76mm/2.99in, 89mm/3.50in, 108mm/4.25 in. The wall thickness is 30mm..
  • 4. Applicable places: suitable for handles, fitness equipment, room sound insulation, hot and cold pipes, air-conditioning pipes, bathrooms and solar water heaters, etc..
Check Stock