Top Led Digit Tube Reviews

uxcell Common Cathode 10 Pin 1 Bit 7 Segment 1.1 x 0.79 x 0.35 Inch 0.55\ Red LED Display Digital Tube 10pcs

  • Panel Size: 19 x 12.7 x 8mm / 0.75" x 0.5" x 0.31" (L*W*H).
  • Total Size: 19 x 12.7 x 14mm / 0.75" x 0.5" x 0.55" (L*W*H).
  • Package Content: 10 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 10 Pin 2 Bit 7 Segment 1.41 x 1.02 x 0.39 Inch 0.8\ Red LED Display Digital Tube 2pcs

  • Panel Size: 35.8 x 25.8 x 10mm / 1.41" x 1.02" x 0.39" (L*W*H).
  • Total Size: 35.8 x 25.8 x 14mm / 1.41" x 1.02" x 0.55" (L*W*H).
  • Package Content: 2 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 10 Pin 2 Bit 7 Segment 0.59 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 15 x 14 x 7.2mm / 0.59" x 0.55" x 0.28" (L*W*H).
  • Total Size: 15 x 14 x 13.5mm / 0.59" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Anode 10 Pin 2 Bit 7 Segment 0.59 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 15 x 14 x 7.2mm / 0.59" x 0.55" x 0.28" (L*W*H).
  • Total Size: 15 x 14 x 13.5mm / 0.59" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 12 Pin 4 Bit 7 Segment 1.18 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 30 x 14 x 7.2mm / 1.18" x 0.55" x 0.28" (L*W*H).
  • Total Size: 30 x 14 x 13.5mm / 1.18" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Cathode 11 Pin 3 Bit 7 Segment 0.89 x 0.55 x 0.28 Inch 0.35\ Red LED Display Digital Tube 5pcs

  • Panel Size: 22.5 x 14 x 7.2mm / 0.89" x 0.55" x 0.28" (L*W*H).
  • Total Size: 22.5 x 14 x 13.5mm / 0.89" x 0.55" x 0.53" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Anode 12Pin 4 Bit 7 Segment 1.98 x 0.75 x 0.31 Inch 0.55\ Red LED Display Digital Tube 5pcs

  • Panel Size: 50.3 x 19 x 8mm / 1.98" x 0.75" x 0.31" (L*W*H).
  • Total Size: 50.3 x 19 x 14.5mm / 1.98" x 0.75" x 0.57" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Anode 12 Pin 3 Bit 7 Segment 1.48 x 0.75 x 0.31 Inch 0.55\ Blue LED Display Digital Tube 5pcs

  • Panel Size: 37.6 x 19 x 8mm / 1.48" x 0.75" x 0.31" (L*W*H).
  • Total Size: 37.6 x 19 x 14.5mm / 1.48" x 0.75" x 0.57" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

uxcell Common Anode 12 Pin 3 Bit 7 Segment 1.48 x 0.75 x 0.31 Inch 0.55\ Yellow Green LED Display Digital Tube 5pcs

  • Panel Size: 37.6 x 19 x 8mm / 1.48" x 0.75" x 0.31" (L*W*H).
  • Total Size: 37.6 x 19 x 14.5mm / 1.48" x 0.75" x 0.57" (L*W*H).
  • Package Content: 5 x LED Digital Display Tube.
Check Stock

SEEU. AGAIN 4pcs 8-Digit 7 Segment Module MAX7219 8 Bit Digital Segment Tube LED Display Module Supports Cascade Eight Bit Serial 3 IO Ports for MCU/51/AVR/STM32

  • MAX7219 is an integrated serial input / output common-cathode display driver, which connects your microprocessor to a 7-segment digital LED display with 8 digits.
  • MAX7219 digital display control module, you can use it..
  • The module is compatible of 5V / 3.3V microcontroller.
  • Only three IO ports are used to drive the eight digit display..
  • Only three IO ports are used to drive the eight digit display. MAX7219 supports flicker free displays as well as cascading displays.
  • PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen..
  • Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01.
  • Digital tube is 0.36 inch 4-bit integrated cathode digital tube.
  • Note:VCC and GND do not reversed, it would burn the chip.51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines..
Check Stock

Metra GM Speaker Harness (72-4568) (72-4568)

  • BATTERY VOLTAGE MONITOR: The Voltmeter will Flash Constantly When the Voltage is Lower than 11.5V or Higher than 19.8V..
  • EASY TO INSTALL: Only Two Wires, The Red Connects to Positive and Black Connects to Negative. No separate power supply is required.
  • Mini size with 3-digit LED Digital Display. Simple connection, easy to use, and waterproof..
  • DC 12V MOTORCYCLE VOLTMETER: It is perfect to Monitor the Condition of the Battery, You can Use It on Your Motorcycle, Car, Trailer, and Boat Marine Vehicle Truck ATV UTV Car Camper Caravan, etc..
  • WIDE APPLICATION: Widely used for cars, motorcycles, bikes, substation automation, distribution automation, test equipment, voltage regulator, and so on..
  • LARGE LED DISPLAY:Operation voltage: DC 8 – 16 Volt.
  • Display mode: 0.56 inch digital tube. The display shows L.L.L. to warn when the voltage is below 8 Volt.
  • the Display shows H.H.H. when the voltage is over 16 Volt..
Check Stock

ALAMSCN LED Display Module TM1637 0.36'' 4-Digit 7 Segment 4 Bits Red Digital Tube for Arduino Driver Board (Pack of 4)

  • 4-digit LED display module, red highlights, with adjustable LED brightness and clock point, can display decimals, letters, etc..
  • The driver IC is TM1637, compatible with Arduino..
  • The digital display tube can be controlled with only two signal lines, simple and easy to use..
  • Control interface: a total of 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
  • 4 M2 screw holes, easy to install, locate and combine modules..
Check Stock

4Pcs MAX7219 8 Digit 7 Segment LED Tube Display Control Module for MCU/51/AVR/STM32

  • MAX7219 is an integrated serial input / output common-cathode display driver, which connects your microprocessor to a 7-segment digital LED display with 8 digits.This module is compatible with 5V and 3.3V microcontrollers, and you you can use it.
  • Material: PCB+Electronic components, LED color: Red.
  • Only three IO ports are used to drive the eight digit display. MAX7219 supports flicker free displays as well as cascading displays. PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen..
  • Wiring instructions (take the provided program as an example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01.
  • Digital tube is 0.36 inch 4-bit integrated cathode digital tube.
  • Note: VCC and GND should not be connected reversed, so as not to burn the chip.
  • 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines..
  • A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding..
Check Stock