Top Isolated Switch Reviews

Blue Sea Systems Battery Switch m-Series Selector, Black, 6007200

Blue Sea Systems Battery Switch m-Series Selector, Black, part number 6007200, is a Selector 4 Position switch. Switches isolated battery banks to all loads or combines battery banks to all loads.
IP66 waterproof, ISO 8846 and meets ABYC requirements. Ignition protected—safe for installation aboard gasoline powered boats.
Make before break contact design allows switching between battery banks without power interruption.
Continuous Rating: 300A, Maximum Voltage: 32V DC.

Check Stock

CR Magnetics CR9380-PNP-M PNP Transistor Output Split Core Current Switch with Mounting Case, Normally Open, 30 VDC

Current switch for monitoring current flow.
Current carrying wire is routed through an aperture.
Electrically isolated normally open (NO) switch.

Check Stock

LoveRPi Compact PoE HAT with PWM Fan Controller for Raspberry Pi 4

COMPACT RASPBERRY PI 4 POE HAT: Ideal for non-grounded installation, this NON-ISOLATED PoE HAT features optimized footprint. Must be used with a standards compliant IEEE 802.3af PoE or 802.3at PoE+ switch that complies with Section 33.4.1 for power sourcing equipment (PSE) electrical isolation. "Passive PoE" (DC 24V or 48V) is not standards compliant and may cause damage to equipment if connected improperly. Some Ubiquiti switches are not properly isolated and require isolated PoE HATs..
GROUND LOOPS WARNING: Do not use this device with grounded USB peripherals, HDMI displays, and attachments. Please use the professional PoE model with isolation transformer to prevent electrical loops. In non-controlled PoE applications, ALWAYS use the professional PoE model..
INTEGRATED PWM FAN CONTROLLER: Based on the EMC2301 SMBus compliant fan controller, this PoE HAT is fully programmable over I2C to control standard 4-pin PWM fans. Set user-space or device-tree based temperature or event triggers for complete fan control from off to maximum RPM. Fan speed tach also provides stall detection, spin-up control, and ramp rate control with 1% accuracy from 500-16K RPM..
VENTILATED CASE WITH FAN HIGHLY RECOMMENDED: Do not use this product in an enclosed case without acti....

Check Stock

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
With optical coupling isolation, triggering more reliable, more stable..
EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..

Check Stock

AIMS Power PWRIG200012120S 2000W Pure Sine Inverter Continuous 4000W Surge Peak Power 12V DC Input 60hz or 50hz Switch 1 GFCI Dual Outlet

2000W continuous power, 4000W surge peak power, 12 Volt DC input, 60hz or 50hz switch.
Highly efficient - improved ouptut at low voltage, 1 GFCI Dual Outlet.
Connector and cable for remote on/off switch, Isolated ground & neutral.
Short circuit protection (GFCI and AC Breaker), On/off switch, 5 Function Protection LED indicator.
AC Breaker, Dual cooling fans thermally controlled, Internal blade fuse protection, Instruction manual.

Check Stock

Off-Line Controller,DDCSV3.1 3 Axle Off-Line Controller with Emergency Stop Function Handwheel Kit,Strong Anti-Interference Ability, Long-Distance Transmission

[SMART]Support the origin and Limit share the same Input ports.The controller only support NPN type limited switch.Support the operation of quickly specify the running position and ''Power Cut'' recovery. Data is automatically saved..
[PROFESSIONAL ] 16 opto isolated digital inputs,3 opto isolated digital outputs.3axle motor Control.Differential Pulse and direction output signal,maximum.500Khz per axle..
[EASY TO USE]ARM9 main control chip,FPGA core algorithm chip.5 inches TFT screen, resolution ratio: 480x272,17 operation keys. Analog spindle control 0-10V spindle control (can be modified as PWM output)..
[HIGH QUALITY ]Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version..
[WIDELY USED] Applications: CNC machine tools, printing machinery and other zero correction and signal segmentation..

Check Stock

Voodoo Lab Pedal Power X4 Isolated Power Supply

Ultra-compact chassis easily mounts to the smallest pedalboards.
Unique DC transformer topology provides optimum platform for QUIET switch-mode power.
Includes power cables, Universal input power adapter with detachable AC line cord, and 3M dual lock for mounting.

Check Stock

Voodoo Lab Pedal Power X4 Isolated Output Expander Kit

Adds four 9V isolated outputs to an existing pedal power.
Powered from any Voodoo Lab pedal power 12V 400mA output.
Ultra-compact chassis easily mounts to the smallest pedalboards.
Unique DC transformer topology provides optimum platform for QUIET switch-mode power.

Check Stock

Blue Sea Systems 2136 CIRCUIT BREAKER PUSH BUT ST 30A

Yellow Manual Reset button 80 Amp Miniature Circuit Breakers,4 Gauge Plated Inputs.
Compact and lightweight design,Protects your trolling motor from electrical damage, prevents excessive current and stops power surges from damaging Amps.
Visible Red manual reset lever shows open condition, unique push button reset Can also be used as a kill switch. Button on circuit breaker can act as a master disconnect for circuits.
Housing is thermalplastic UL rated 94V0，Surface mount cover protective the stud to be isolated, splash, waterproof IP 67.
Typically used in auxiliary and accessory circuits for Boat, Marine, RV, Caravan, Winch, Tractor and ATV applications. Also can used as an on/off button switch for the battery or DC sound system.

Check Stock

DDCSV3.1 3 Axis Offline CNC Motion Controller Handwheel G Code PLC Control System Electronic Handwheel with Emergency Stop Function

Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version. ARM9 main control chip,FPGA core algorithm chip. 16 opto isolated digital inputs,3 opto isolated digital outputs..
3 axle motor Control.Differential Pulse and direction output signal,maximum.500Khz per axle. Analog spindle control 0-10V spindle control (can be modified as PWM output). Jog function for each axle (continuous, step, defined distance). 24VDC power input, minimum Current is 0.5A..
5 inches TFT screen, resolution ratio: 480x272,17 operation keys. USB flash disk support for G code file input,no size limited of the G-code file. 1GB internal memory and support standard MPG..
Support the operation of quickly specify the running position and ''Power Cut'' recovery. Data is automatically saved. Support the origin and Limit share the same Input ports.The controller only support NPN type limited switch..
Drive output type, strong anti-interference ability, long-distance transmission. Applications: CNC machine tools, printing machinery and other zero correction and signal segmentation..

Check Stock

Aumox 5 Port Gigabit PoE Switch, 4 Port PoE 78W, Gigabit Ethernet Unmanaged Network Switch, Sturdy Metal Housing, Plug and Play, Traffic Optimization (SG305P)

【4-Port 78W PoE】Designed with IEEE802.3af/at standard, Aumox PoE ethernet switch can transmit network data and power at the same time. This gigabit switch offers a maximum 78W PoE power output in total. Single-port POE power up to 30W, meets power supply requirements of various applications..
【Gigabit Ethernet】Aumox network switch features 100/1000 Mbps ports, enables ultra-fast wired connectivity and instant large files transferring. Unmanaged gigabit switch, easy to setup, plug and play..
【Reliable Fanless Metal Housing】Metal housing design makes the PoE switch reliable to use in different use cases. Fanless design give you a quiet and noise free environment..
【One-Key VLAN】Supports one-key VLAN mode, and ports are isolated from each other. Effectively suppress network faults such as network storms, ensuring good network transmission performance and security..
【Intelligent Recognition】Intelligently identify whether the IP terminal supports power supply,protect powered device..

Check Stock

DDCSV3.1 Standalone Motion Controller off-line 100 Pulse MPG Handwheel Emergency Stop for CNC Router Engraving Machine (3-Axis with MPG)

16 opto isolated digital inputs,3 opto isolated digital outputs.Analog spindle control 0-10V spindle control (can be modified as PWM output).Drive output type, strong anti-interference ability, long-distance transmission..
Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version.5 inches TFT screen, resolution ratio: 480x272,17 operation keys..
4 axle motor Control.Differential Pulse and direction output signal,maximum.500Khz per axle.24VDC power input, minimum current is 0.5A. Support the origin and Limit share the same Input ports.The controller only support NPN type limited switch..
ARM9 main control chip,FPGA core algorithm chip.1GB internal memory and support standard MPG.Jog function for each axle (continuous, step, defined distance)..
USB flash disk support for G code file input,no size limited of the G-code file.Support the operation of quickly specify the running position and ''Power Cut'' recovery. Data is automatically saved.Applications: CNC machine tools, printing machinery and other 0 correction and signal segmentation..

Check Stock

4 Axis 500Khz Offline Stand Alone CNC Motion Controller System PLC G code Servo/Stepper Motor Control Replace Mach3+100PPR MPG Handwheel with emergency stop for CNC Router Engraving Machine DDCSV3.1

5 inches TFT screen, resolution ratio: 480x272,17 operation keys.
♞【Feature】16 photoelectric isolated digital inputs,3 photoelectric isolated digital outputs.
the highest output pulse per axis is 500KHz. This....
♞【SB flash disk】4G USB flash disk support for G code file input,no size limited of the G-code file.
ARM9 main control chip,FPGA core algorithm....
♞【Power requirements】The Power Supply for the controller is 24VDC,DDCSV3.1 needs two power supplies,main power is for system,IO port is for....
♞【MPG with 15-pin connector】MPG Resolution:100PPR.
DDSCV3.1 Version enhenced Algorithm,support soft interpolation,fixed arc....

Check Stock