Top Intelligent Asphalt Distributor Reviews

BoltHold - AK-4 Asphalt Anchor & Anchoring Cement Kit - Four 1500lb Pull Rated SP10-38 Chemical Anchors 5/8 x 6 with EPX2 Anchoring Cement - For Installation of Sheds Carports Bike Racks & More

  • ASPHALT ANCHORING KIT: Stop wasting time pouring concrete! BoltHold's industrial in-ground anchors and anchoring grout allow you to install anything on asphalt in three simple steps, offering a fast, cost-effective, and reliable solution to asphalt mounting. This AK-4 Kit includes four SP10-38 (3/8"-16 x 6") Zinc-Plated Anchors with a pre-installed 1" long bolt and 1" diameter washer and two bags of EPX2 cement-based Anchoring Grout..
  • LIGHT-TO-MEDIUM LOAD: Pull rated for 1,500 lb! Designed for a light-to-medium load, BoltHold SP10-38 chemical anchors resist at least 1,500 pounds pull and 1,000 pounds of moderate shear force at ground level. Rated for 200 in-lb rotary torque, the anchor's welded spiral offers a strong bond with the grout, while the washer at the top prevents the anchor from dropping below the surface or being pulled up into the mounting plate when tightening the bolt..
  • LONG TERM STABILITY: Creates a stress-free bond that lasts! Due to asphalt's weaker nature, typical expansion-type wedge anchors used in concrete won't hold to the pressure. BoltHold anchors solve this problem by embedding deep into the compacted gravel below the asphalt layer to increase the shear resistance and ensure long-lasting stability—perfect for safely installi....
Check Stock

ASPHALT PATCH & POTHOLE FILLER 56 lb Pail | Pothole Repair Kit | Driveway Patch | Paving Patch - 5 Gallon Pail

  • FIX POTHOLES FAST. This all-in-one pothole filler takes the pain out of patching asphalt. Holds up against years of motor traffic for a long-lasting solution, or your money back..
  • NO PREP NEEDED. No need for primer, mixer, or special preparation. Can be applied in any weather condition. With this driveway patch, you can fill a pothole yourself—no prior experience needed..
  • TRAFFIC READY IN AN HOUR. Safely drive on Asphalt Patch within one hour of application. Boasts a flexible and fast-drying mixture of limestone, quartz, a petroleum solvent, and a petroleum asphalt base..
  • MORE THAN FOR JUST ASPHALT. Don’t stop at roadway cracks. Use Asphalt Patch to fill cracks in concrete, stone, and brick. Perfect for parking lots, playgrounds, and home driveways..
  • STRONG IN MANY WAYS. ASPHALT PATCH works at any temperature above 15 degrees Fahrenheit. The product can be stored indefinitely with no risk of hardening or decay in storage..
Check Stock

GARDENA Automatic 6 Zone Mechanical Water Distributor

  • Automatic Watering for up to 6 Areas: With the GARDENA Water Distributor Automatic, you can effortlessly water up to 6 plant areas in your garden one after the other. Enjoy more free time and healthier plants with this hassle-free watering system..
  • Easy to Operate: Deactivate non-required outlets with the setting lever for easy operation. The Water Distributor works mechanically and doesn't require a battery or power supply..
  • Compact and Flexible Design: The Water Distributor's six outlets are arranged in one direction, saving space and allowing for ground or wall mounting..
  • Full Control Timer Compatibility: Pair the Water Distributor with a GARDENA 1892 Timer and take control of your watering system and personalized watering schedules for each garden area..
  • Quality Made in Europe: The GARDENA Water Distributor Automatic is a high-quality product made in Europe, ensuring long-lasting and reliable performance..
Check Stock

NEW HOLLEY SNIPER EFI HYPERSPARK DISTRIBUTOR FOR CD IGNITION BOX, COMPATIBLE WITH CHEVY SMALL & BIG BLOCK

  • Brand New Holley Sniper EFI HyperSpark Distributor, Compatible with Chevy Small Block & Big Block (Part #565-300).
  • Features: Hall Effect crank trigger sensor housing provides a noise-free RPM signal to the Sniper ECU | Billet distributor housing provides corrosion resistance and stylish looks! | Patented Clear Installation cap eliminates any confusion while installing the distributor | Easiest plug and play way to add timing control to a Sniper EFI Installation | Distributor shutter wheel is pinned and welded to the shaft, for decades of reliable accuracy | Includes Wire Retainer for a clean installation |.
  • Comes with Cast Gear Installed - contact camshaft manufacturer for recommended gear material | Designed to be used with Sniper EFI HyperSpark CD box P/N 556-151 and Ignition Coil 556-152.
  • Specs: Brand: Holley Sniper EFI | Emission Code: 3 | Material: Shiny Billet Aluminum | Product Type: Distributor.
  • HyperSpark distributors are plug and play with all Holley Sniper EFI systems, featuring a high-quality billet distributor housing, hall effect crank trigger sensor, and they com....
Check Stock

WFLNHB 8Pin Distributor Adapter Obd1 to Obd2 Jumper Harness Dizzy fit for Honda Acura E3

  • This Distributor Adapter Fit For 1999-2000 Civic.
  • (Does Not Work For Dohc / Si Model)With An 8-Position Distributor Plug, To Plug Into A Obd1 (92-95) Distributor..
  • Package Included:1 X Distributor adapter.
Check Stock

Clemons Concrete Coatings Supreme Shield SB-600 Wet Look Concrete Sealer 5-Gallon, Clear

  • ✅ SEAL ASPHALT LIKE A PRO - Be extra efficient with sealing asphalt. This sealcoating equipment has all the accessories you need for residential and commercial projects. One tank can cover up to 23,000 square feet..
  • ✅ OPERATE WITH EASE - Our spray system uses proprietary Quick Connect fittings that simplify everything from assembly to cleaning. Its custom valves also make it easy to switch between its two modes..
  • ✅ TOOLLESS OPTIMIZATION - Quick Connect fittings allow the user of this asphalt equipment system to optimize application rate, fan pattern, and pressure without the need for any special tools..
  • ✅ AMPLE SPRAYING POWER - This asphalt sealer machine features a balanced engine that generates just enough power to maintain optimal spray pressure without wearing down the system’s components..
  • ✅ STURDY & COMPACT - Made from 11-gauge steel, this asphalt repair sprayer is remarkably durable. Its compact form also allows it to fit most utility trailers and medium-sized pick-up trucks..
Check Stock

Unlimited Rider Engine Harness OBD2 8-Pin to OBD2 10-Pin DISTRIBUTOR ADAPTER JUMPER HARNESS For HONDA Civic 1999-2000 Single Overhead Cam Civic with an 8-pin Distributor Plug 1.6L 1590cc

  • This adapter is made for a 1999-2000 single overhead cam Civic with an 8-pin distributor plug converting to a OBD2 10-pin distributor..
  • Plug and play, no modifications required.
  • This is an exact replacement DISTRIBUTOR ADAPTER JUMPER HARNESS for your model..
  • Trust this DISTRIBUTOR ADAPTER JUMPER HARNESS to work perfectly in demanding conditions..
  • PLEASE LOOK AT THE PICTURE TO MAKE SURE IT WILL ADAPTER TO YOUR DISTRIBUTOR, MANY THANKS..
Check Stock

51mm Coffee Distributor and Tamper, Espresso Distributor and Espresso Tamper, Espresso Distribution Tool for All 51mm Espresso Portafilter, Depth-adjustable Coffee Leveler, Detachable Tamper

  • ★Dual Head: Distributor/Leveler and tamper are designed in one, double sides are available. The unique four-page propeller design ensures that your coffee powder are balanced..
  • ★More Convenient: You can adjust the depth of this Espresso Distributor to the position you need. And with the scale, you only need to adjust one side, and the other side is adjusted to the corresponding position. Our espresso tamper is more convenient to use..
  • ★Safe Material: This coffee distributor is made of food-grade 304 stainless steel, it enables you to feel reassurance when you make espresso. Plus, every part of this espresso tamp is removable, this makes it easy to clean..
  • ★51mm Coffee Distributor & Tamper: This 51mm Coffee distributor and hand tamper are specially designed to work with all 51mm espresso portafilter, including Delonghi EC0680, EC0685 bottomless portafilter..
  • ★Simple to Use: With a simple twist to adjust the depth, then you can use the paddle surface to even out the coffee powder before tamping it with the flat surface. If you have any questions with the coffee distribu....
Check Stock

100 Feet Asphalt Joint and Crack Sealer Asphalt Crack Filler Asphalt Patch Driveway Crack Filler Bitumen Tape Asphalt Joint Repair Tape for Parking Lot Roof Asphalt Cement Road (2 Inch)

  • You Will Get: there are 2 rolls of asphalt crack tapes, each roll is 50 feet in length, 2 inch in width, enough length can meet your using needs.
  • Reliable Material: the asphalt repair patch is made of quality asphalt material, which is safe and reliable, waterproof and sunscreen, not easy to fray or fracture, high temperature resistant, not easy to melt, with high tensile strength, can be bent at will, serving you for a long time.
  • To Use: the asphalt tape is convenient to use, just clean up the crack, peel off the backing film, then paste the tape on the crack that need to be repaired, and press down firmly.
  • Its softness helps to fit most types of bending cracks, can fully fill the crack to achieve the ideal effect.
  • Self Adhesive: the asphalt filler sealer adopts self adhesive design, can be directly pasted, no need of heating device, saving your time and energy, and features nice adhesion, not easy to fall after pasting.
  • Widely Applicable: the blacktop crack filler is suitable to repair the cracks of expressway, ordinary highway, urban sidewalk, road, etc., fitting for cement and asphalt pavement.
Check Stock

Asphalt Crack Repair Tape Driveway Sealer Filler Joint Repair Tape Patch Crack Filler Parking Lot Self Adhesive Bitumen Tape for Road Parking Lot Roof, No Heating Need 2 Inch x 32.8 ft 2.5 mm Thick

  • Self Adhesive Asphalt Crack Tape: the asphalt crack filler adopts self adhesive design that it can be applied directly, no heating equipment needed, easy and effective.
  • Good Stickiness: the asphalt repair patch features good viscosity, which fits more tightly into the road, waterproof and sunproof, suitable for most kinds of road cracks, not easy to melt.
  • Simple to Use: the asphalt patch filler is simple to apply, just clean up the cracks, peel off the film on the flat surface of one end of the crack repair tape, stick the tape on the cracks that need to be repaired, and compress it, and its softness helps to adapt to most kinds of bending cracks.
  • Quality and Reliable to Use: the asphalt crack tape is made of quality material, which is reliable and safe to use, not easy to fray or break, suitable for road surface with different altitude and temperature.
  • Applicable Occasions: the adhesive joint tape is designed for repairing cracks in expressway, ordinary highway, city pavement and road, etc., suitable for road surface made of cement and asphalt.
Check Stock

Jetcoat Premium Elastomeric Asphalt Crack Filler and Sealant, Perfect for Blacktop Repair (1 Gallon)

  • LONG-LASTING SEALANT – Fortified with plasticizers for added flexibility, Jetcoat Premium Elasto Asphalt Crack Filler is designed to enhance and repair asphalt pavement surfaces. This asphalt driveway filler is polymer-modified and emulsion-based for ultimate sealing power..
  • GREAT FOR MULTIPLE SURFACES – Use this extra strength driveway filler on all types of asphalt pavements and blacktop surfaces. Quickly fill in cracks, holes, gaps, and breaks with this dynamic and powerful sealant in parking lots, airports, athletic courts, driveways, traffic safety islands, playgrounds, and walkways..
  • READY TO USE – This sealant comes ready to fill and seal any blacktop surface. Simply stir the sealer to a uniform consistency and continue to stir throughout the application process. Dries black..
  • EASY APPLICATION – Shake well and use the included spout to pour product into the crack slightly above surface level. The material may settle, requiring a second application. Always allow 24 hours between applications. To prevent cracking or tracking, avoid heavy or uneven application..
  • LONG-LASTING REPAIR – Our polymer-modified asphalt emulsion-based crack sealant has resilient characteristics that allow for self-healing quality and lasting results. It has excelle....
Check Stock

53mm Coffee Distributor & Tamper - Fits 54mm Portafilters - Adjustable Depth Espresso Tamper For Professional Espresso - Dual Head Leveler For Easy Hand Tamper Use

  • Enjoy Improved Espresso Shots - As you spin the coffee distributor, it evenly spreads grounds and fills gaps within the portafilter to reduce channeling and provide a smoother, richer shot..
  • Tamp Confidently - The adjustable tamping depth allows you to refine your desired pressure, and lock in the depth to produce repeatable results. When fully tamped, the collar will sit flush with your portafilter basket to ensure a level tamp and even water distribution across your coffee for a better extraction..
  • Quick and Easy Use - Our diamond pattern grip provides easy handling. With the compact 2-in-1 design, you can quickly move from distributing to tamping..
  • Know It Fits - Use the size chart in our product images to find the correct tamper size for your machine. The 53mm distributor and tamper fits machines with 54mm portafilters such as Breville Bambino, Breville Bambino Plus, Breville Barista Express, Breville Barista Pro, Breville, Barista Touch, Breville Duo-Temp Pro, Breville Infuser. Note: Breville 800 Series requires a 51mm distributor and tamper, and Breville Oracle Touch requires a 58mm distributor and tamper..
  • Our Promise to You - We are a family-owned brand focused on helping people make great coffee. If you are not happy with your 53mm distributor a....
Check Stock

MSD CRATE IGNITION KIT,READY-TO-RUN DISTRIBUTOR,BLASTER SS COIL,8.5MM SPARK PLUG WIRES WITH SEPARATORS & BILLET HOLD-DOWN CLAMP,COMPATIBLE WITH FORD 351W ENGINES

  • Brand New MSD Crate Ignition Kit, Compatible with Ford 351W Engines, Produced by Holley Performance Products (Part #84746).
  • Includes: Built-in Rev Limiter | Ready-to-Run Distributor | Blaster SS Coil | 8.5mm Spark Plug Wires with separators | Billet hold-down clamp.
  • Specs: Brand: MSD | Color: Red | Distributor Type: Ready To Run | Emission Code: 3 | Engine: Ford 351W | Gear: Steel | Product Type: Distributor.
  • These kits are supplied with everything you need for your ignition. The Ready-to-Run distributor is a great choice for your engine. They feature a high output module that produces a vigorous jolt across the plug gap and the installation is simple with just three wires to connect!.
  • The Blaster SS Coil is a compact and efficient coil that is easy to mount and the system is complemented with MSD's red 8.5mm Super Conductor wires. The wires are supplied as a universal fit, with our straight/multi-angle boots and terminals on the spark plug side and after you route them and cut to length, you simply install the distributor side terminal and boot. Our Pro-Clamp separators keep ....
Check Stock