Top Industrial Water Testing Reviews

16 in 1 Water Test Strips Professional Hardness Testing Kits, Tap and Well Water Test Strips with Hardness PH Mercury Lead Iron Copper Chlorine Nitrate Chromium Cyanuric Acid and More, (100 PCS)

  • ...ut direction. Third: Compare with the color chart. No need to send specimens, no need to go to the lab, you can do it yourself..
  • 【Wide Range of Applications】: The test strips are suitable for testing drinking water, household taps, well water, tap water, swimming pools, hot tub spas, aquariums, ponds, aquariums, industrial wastewater, etc. You can also check whether your water reducing agent works..
  • 【Outstanding Customer Service】: Ensuring that you get the correct water test results is our number one goal. If you have any questions, please contact us and our team will do their best to keep you satisfied..
Check Stock

Gasket Material, General Purpose, NSF-61 Certified, 1/64\ Thick, 30\ x 30\ (1 Sheet) V

  • Certification to NSF-61 provides assurance to a highest level that this material is safe for use in drinking water service..
  • NSF-61 SSS Compressed Fiber Sheet technology provides mechanical and service characteristics unmatched by standard elastomeric grades.
  • When a gasket is submitted for testing, the formulation is reviewed for prohibited substances, and then tested for contaminants that could leach out of the gasket into your drinking water.
  • Temperature: Continuous Service: 500ºF (260ºC),Maximum Service: 752ºF (400ºC), Pressure: Continuous Service: 1160 psi (80 bar) Maximum Service: 1595 psi (110 bar).
  • Sterling Seal supplied NSF-61 is suitable for service handling the following general media categories: Drinking Water, Diluted alkalis, Industrial gases, General chemicals..
Check Stock

Gasket Material, General Purpose, NSF-61 Certified, 1/32\ Thick, 30\ x 30\ (1 Sheet) D

  • Certification to NSF-61 provides assurance to a highest level that style 7001-NSF-61 supplied by Sterling Seal & Supply is safe for use in drinking water service..
  • NSF-61 SSS Compressed Fiber Sheet technology provides mechanical and service characteristics unmatched by standard elastomeric grades.
  • When a gasket is submitted for testing, the formulation is reviewed for prohibited substances, and then tested for contaminants that could leach out of the gasket into your drinking water.
  • Temperature: Continuous Service: 500ºF (260ºC), Maximum Service: 752ºF (400ºC), Pressure: Continuous Service: 1160 psi (80 bar) Maximum Service: 1595 psi (110 bar).
  • Sterling Seal & Supply #7001-NSF-61 is suitable for service handling the following general media categories: Drinking Water, Diluted alkalis, Industrial gases, General chemicals..
Check Stock

Gasket Material, General Purpose, NSF-61 Certified, 1/32\ Thick, 10\ x 10\ (1 Sheet) V

  • Certification to NSF-61 provides assurance to a highest level that style 7001-NSF-61 supplied by Sterling Seal & Supply is safe for use in drinking water service..
  • NSF-61 SSS Compressed Fiber Sheet technology provides mechanical and service characteristics unmatched by standard elastomeric grades.
  • When a gasket is submitted for testing, the formulation is reviewed for prohibited substances, and then tested for contaminants that could leach out of the gasket into your drinking water.
  • Temperature: Continuous Service: 500ºF (260ºC),Maximum Service: 752ºF (400ºC), Pressure: Continuous Service: 1160 psi (80 bar) Maximum Service: 1595 psi (110 bar).
  • Sterling Seal & Supply #7001-NSF-61 is suitable for service handling the following general media categories: Drinking Water, Diluted alkalis, Industrial gases, General chemicals..
Check Stock

Gasket Material, General Purpose, NSF-61 Certified, 1/32\ Thick, 30\ x 30\ (1 Sheet) V

  • Certification to NSF-61 provides assurance to a highest level that style 7001-NSF-61 supplied by Sterling Seal & Supply is safe for use in drinking water service..
  • NSF-61 SSS Compressed Fiber Sheet technology provides mechanical and service characteristics unmatched by standard elastomeric grades.
  • When a gasket is submitted for testing, the formulation is reviewed for prohibited substances, and then tested for contaminants that could leach out of the gasket into your drinking water.
  • Temperature: Continuous Service: 500ºF (260ºC),Maximum Service: 752ºF (400ºC), Pressure: Continuous Service: 1160 psi (80 bar) Maximum Service: 1595 psi (110 bar).
  • Sterling Seal & Supply #7001-NSF-61 is suitable for service handling the following general media categories: Drinking Water, Diluted alkalis, Industrial gases, General chemicals..
Check Stock

Sea Foam SS14 Upper Engine Cleaner and Lube (4 pack)

  • Powerful degreaser removes oil, dirt, grime, and grease from machinery and all types of engines.
  • Low-residue, water- based foaming formula penetrates deep into crevices for completely clean results.
  • Recommended application areas include auto and truck engines, industrial machinery, and farm equipment.
  • Nozzle sprays degreaser up to 5 ft. for long-distance application. It sticks to whatever you spray it on. Included straw creates a precision stream of cleaner for controlled application.
  • In independent laboratory testing, WD-40 Specialist Machine & Engine Degreaser Foaming Spray outperforms the leading competitors.
Check Stock

GP66 Green Miracle Cleaner, Gallon Cleans Over 1,000 Surface Types All-In-One Powerful NSF Approved

  • REMOVES THE TOUGHEST DIRT, GREASE, AND GRIME FROM JUST ABOUT ANYTHING ANYWHERe! GP66 is a water based and proprietary all in one cleaning solution initially developed for industrial use. Now, its in homes all across America..
  • MADE IN AMERICA, NSF APPROVED, NO ANIMAL TESTING.
  • ONE-DO-IT ALL SOLUTION! GP66 cleans ovens, carpets, pots and pans, concrete, brick, grout, laundry, equipment, microwaves, spray paint, grills, airway strips, graffitti, automobiles, floors, wine, blood, pet mess, tables, golf clubs, fireplaces, bacon grease, laminate floors, roofs, vinyl, glass, furniture, stove tops, walls, and more!.
  • THE MOST EFFECTIVE AND POWERFUL FORMULA! When you clean with water and other detergents, you are not getting results because water is like a film that sits on top of a surface rather than penetrating through it. GP66 breaks the surface tension of water which allows GP to mix and emulsify your stain..
Check Stock

HEATIT HISD 18-feet Pipe Heating Cable with Built-in Thermostat

  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 15-feet Pipe Heating Cable with Built-in Thermostat

  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

HEATIT HISD 12-feet Pipe Heating with Built-in Thermostat, Black

  • ...ng grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

New Stainless Steel 304 Dual Scale Liquid Filled Pressure Gauge,Premium Spa Pool Aquarium Water Pressure Gauge,2.5\ Dial Display, 1/4\ NPT Bottom Mount (2, 0-100PSI)

  • Clear And Accurate: Pool Pressure Gauge Provides Accurate Readings of Filter Pressure Pump from 0 to 100 PSI..
  • Product Parameters:2.5" DIAL Display, 0-300 PSI,+/-1.5% Accuracy,1/4" NPT Bottom Mount,3/4" hose adaptor.
  • Applications: Swimming Pools, Spas, Hot Tubs, Aquariums Residential & commercial pressure testing of water lines,Potable water systems,Industrial Pressure test Gauges..
  • Commitment:If You Are Not Happy With Your Purchase We Will Issue a 100% Refund - No Questions Asked!.
Check Stock

HEATIT HISD 3-feet Pipe Heating with Built-in Thermostat, Black

  • ...ng grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Only use 5 amps or less of electricity. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8” and less than 1 1/2” in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don’t plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock

DEWENWILS Roof Heat Cable, 6ft Heat Tape for Pipe, Gutter, Roof, Self-Regulating Cable Pre-Assembled, UL Listed

  • Pre-assembled easy to install. Including grounded plug with light, built in thermostat, and instructions. Easy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
  • Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
  • Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight..
  • Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..
Check Stock