Top Incra Miter Sled Reviews

INCRA MITEREXPRESS Miter Express

  • If you own a miter gauge - any miter gauge.
  • This sled is a sliding, miter-cutting platform that fully supports and controls your work piece throughout the cut.
  • Miter gauges drag your board across the table, a sled slides the work piece giving more support and control creating better, more consistent cuts.
Check Stock

SWAG Off Road Incra V27 Miter Gauge

  • The INCRA V27 miter gauge is made in the USA, and build to last as long as our tables..
  • The V27 features four adjustable expansion joints to eliminate any side play in the miter track..
  • The V27 also features their AngleLOCK indexing for quick tool free angle adjustment..
Check Stock

18” Precision Steel Miter Bar Rail Runner with Adjustable Spring Loaded Plungers For DIY Table Saw Crosscut Sleds, Jigs and Fixtures to Slide in 3/4 inch by 3/8 inch Miter Slots

  • Build your next table saw sled, router table jig or band saw fixture to operate with a smooth sliding action using the Fulton 18 inch Precision Steel Miter Bar! Attach the steel bar to most any type of sled, jig or fixture that is to be used with a 3/4 inch (19mm) by 3/8 inch (9mm) miter slot. Using our steel bar versus plastic or aluminum gives your sled, jig or fixture more strength and stability and it won’t bend or warp..
  • When building sleds, jigs and fixtures one of the most important aspects is to achieve a smooth sliding action without side to side play. The Fulton Precision Steel Miter Bar does both with its solid steel bar and 4 adjustable spring loaded plungers. The plungers can be adjusted with the included hex key wrench for just the right fit..
  • Not only is the Fulton Steel Miter Bar adjustable, its easy to mount! You can mount the bar from the top of your sled, jig or fixture platform or base, or you can mount it from the bottom. There are three threaded holes along the length of the bar for mounting the bar using 1/4 inch by 20 tpi machine screws (not included). There are also three counter sunk holes on the bar to mount the bar using #8 wood screws (not included)..
  • Once you mount the bars to your sled, jig or fixture you are sure to fee....
Check Stock

Miter T-Bar for Jigs Fixtures Sleds Router Tables and General Woodworking 48 inch MADE IN THE USA

  • When building sleds, jigs or fixtures for your woodworking projects that help keep your fixtures from moving or to help your sleds and jigs slide through a track, the Miter T Bar may just be the perfect solution. The Miter T Bar does this bit fitting neatly into most standard miter slots that measure ¾” x 3/8”. The aluminum bar can be used to slide your sleds or it can be used to lock fixtures like featherboards (when cut into smaller length pieces) in place in a miter slot..
  • The T-bar is made in the USA from a solid piece of extruded aluminum and can be cut into sections and drilled as needed. Typical uses for the T-bar are fixtures like featherboards where the featherboard needs to be kept stationary to apply consistent pressure. The T-bar also works great for sleds and other sliding fixtures like cutoff sleds on a table saw or coping sleds on a router table..
  • When mounting the Miter T-Bar it is a good idea to keep in mind that the “T” on the bottom of the track is approx. 1/8” tall, which is just enough to clear the t-slot on most miter slots. If mounted directly to platform for a sled, the tabs may catch and prevent the sled from sliding freely. To remedy this, we recommend using washers between the mounted track and the platform to....
Check Stock

WEN 3962T 3.5-Amp 10-Inch Two-Speed Band Saw with Stand and Worklight

  • CNC laser out of 3/16″ thick steel plate, formed on a CNC press brake..
  • Dual Miter Gauge slides, with optional foot swtich and Incra V27 Miter Gauge.
  • Fits the following models Milwaukee 6232-20, 6232-21, 6238-20, 6238-21& BS125.
  • Fits the following models Milwaukee Fuel M18 2729-20, 2729-21, 2729-22 & CBS125.
Check Stock

Rockler Table Saw Small Parts Sled

  • Sled base and fence provide zero-clearance support—just run it through your saw to locate the kerf.
  • Sled rides in miter track of your table saw—included miter slot stop limits forward travel of sled.
  • Rear-mounted blade guard is adjustable to fit most table saws.
  • Aluminum T-track on top edge of fence lets you add a flip stop (not included) for repeatable cuts.
  • Short T-track parallel to blade accepts an optional T-track hold-down clamp (sold separately).
Check Stock

INCRA MITER1000SE Miter Gauge Special Edition With Telescoping Fence and Dual Flip Shop Stop

  • Engraved stainless steel primary scale for precision accuracy.
  • 41 laser cut V-stops for extreme accuracy at all popular angles.
  • Patented GlideLOCK miter bar with 6 expansion points for quick repeats.
  • 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths.
  • INCRA Flip Shop Stop-Fence Positioner for optimal mitering accuracy.
Check Stock

Flattening Workbenches and Wide Boards with a Router

  • ...n blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place..
  • Many sleds rely on the miter slot for reference. Our coping sled uses the fence as a reference instead. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2” above the base so you won’t cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence.
  • This robust, full featured coping sled has a laminated ½” thick MDF base that slides across your router table surface effortlessly. The sled also features a large, heavy duty hold down toggle with a 1-5/8” hold down foot to keep your stock in place. The unit also includes two large and sturdy handles for guiding the sled through the cutter. The maximum stock size is 5” wide by 1 ¼” thick. Full instructions are included..
Check Stock

3-1/2\ To 4-1/2\ Universal Fence Clamp 2 Pack

  • Our 525 Large Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 10" wide. Heavy duty 1/2" phenolic base (15-3/4" x 15-3/4") will not distort from clamp pressure..
  • Features one 500 lb. Outboard Toggle Clamp and two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 24” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock

The Original Dubby Cut-Off • Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw (Left Side Dubby Sled)

  • THE ORIGINAL DUBBY SLED From standard 4 sided panel cutting to the absolutely stunning heptagon frame you will be completely accurate with the angles on your mitered projects with the Dubby Sled. The Dubby will allow you to make perfect cuts the first time you do them and keep your creative juices flowing with idea after idea. It is ideal for making frames but it also works very well for the cutting of tiny pieces while keeping your fingers out of harms way..
  • WORKING WITH LARGE PANELS The Dubby has the capacity to crosscut panels up to 24″ wide x 52″ long, and allows you to do them safely. Since the panels don’t make contact with the table saw top, “walking” of the material is virtually eliminated. This will allow you to cut perfectly square panels for your furniture and cabinet making projects quickly, easily and accurately..
  • WORKING WITH ANGLES The Dubby angle scale is the simplest, most accurate and easiest to read scale available. Being about 15-20 times more accurate than the average miter gauge, the scale has pre-determined lines for any shape (from 4 to 16 sides) you want to cut. This means no calculations, no hassles, and best of all, no test cuts for perfect results.
  • WORKING WITH SMALL PIECES- No miter gauge on the market can offer yo....
Check Stock

Router line Storage Box Power Cord Socket Sorting Box Set-top Box Rack

  • Our 526 Medium Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it! Two adjustable feed handles provide firm control over the sled and your work..
  • Includes an 11-3/4" adjustable steel miter bar that mounts in 6 different locatons for best placement. Can also be used without the miter bar against your fence..
  • Holds stock up to 6" wide. Heavy duty 1/2" phenolic base (11-5/8" x 11-3/4") will not distort from clamp pressure..
  • Features two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-3/4" thick, or 2-3/4" with optional 6305R Riser Kit (one Riser Kit required for each toggle clamp). Fence is 12” long. Optional 525S Flip Stop available for repetitive work..
  • Lifetime guarantee against defects in material or workmanship. Made in the USA!.
Check Stock

The Original Dubby Cut-Off • Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw (Left Side Dubby and Right Side Dubby Sleds are Included)

  • THE ORIGINAL DUBBY SLED From standard 4 sided panel cutting to the absolutely stunning heptagon frame you will be completely accurate with the angles on your mitered projects with the Dubby Sled. The Dubby will allow you to make perfect cuts the first time you do them and keep your creative juices flowing with idea after idea. It is ideal for making frames but it also works very well for the cutting of tiny pieces while keeping your fingers out of harms way..
  • WORKING WITH LARGE PANELS The Dubby has the capacity to crosscut panels up to 24″ wide x 52″ long, and allows you to do them safely. Since the panels don’t make contact with the table saw top, “walking” of the material is virtually eliminated. This will allow you to cut perfectly square panels for your furniture and cabinet making projects quickly, easily and accurately..
  • WORKING WITH ANGLES The Dubby angle scale is the simplest, most accurate and easiest to read scale available. Being about 15-20 times more accurate than the average miter gauge, the scale has pre-determined lines for any shape (from 4 to 16 sides) you want to cut. This means no calculations, no hassles, and best of all, no test cuts for perfect results.
  • WORKING WITH SMALL PIECES- No miter gauge on the market can offer yo....
Check Stock

Fulton Rail Guide Coping Sled PRO For Cutting Profiles Into The End Grain Of Your Stock | Ideal for Cutting Precise Clean Joints for Cabinet Door and Drawer Fronts

  • ...n blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place..
  • Many sleds rely on the miter slot for reference. Our coping sled uses the fence as a reference instead. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2” above the base so you won’t cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence.
  • This robust, full featured coping sled has a laminated ½” thick MDF base that slides across your router table surface effortlessly. The sled also features a large, heavy duty hold down toggle with a 1-5/8” hold down foot to keep your stock in place. The unit also includes two large and sturdy handles for guiding the sled through the cutter. The maximum stock size is 5” wide by 1 ¼” thick. Full instructions are included..
Check Stock