Top I2c Support Reviews

Clock Splitter, Good Performance High Practical Electronic Component for Industry for Home

  • With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
  • There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
  • Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
  • Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
  • Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
Check Stock

AITRIP 10PCS PCF8574 PCF8574T IO Expansion Board I/O Expander I2C Evaluation Develop Module

  • The PCF8574 IO Expansion Board provides general-purpose remote I O expansion via the two-wire bidirectional I2C-bus (serial clock (SCL), serial data (SDA)..
  • The main resources: PCF8574, I2C interface, the 8-bit parallel.
  • Typical applications: for I / O resource constraints the MCU I / O expansion.
  • PCF8574T expansion board applicable to a variety of platforms including AVR / ARM.
  • PCF8574T PCF8574 IO expansion board support I2C bus cascade (by pin header row seat docking methods can be used simultaneously multiple I2C modules).
Check Stock

RJ45 GPIO Pinout Breakout Board for Raspberry Pi 1A+ 1B+ 2B 3B 3B+ 3A+ 4B Zero-W

  • 8 port(2x4) RJ45 8P8C sockets, with the module you can easily connect Raspberry Pi GPIOs and Power supply to peripheral devices through the RJ45 connector. The module support all 40pin Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B Zero, Zero-W..
  • Each RJ45 port is connected Power Supply and GND. Each RJ45 can independently choose from the Raspberry Pi 5V / 3.3V, or from blue terminal block, to supply power to external devices. The 4 5 pin of all RJ45 ports are connected to the power supply(VCC, V+), and 7 8 pin connected to GND(0V)..
  • RJ45 GPIO connects: Port 1: UART(RXD TXD) GPIO17 GPIO4. Port 2: SPI(SCLK CE0 MISO MOSI). Port 3: GPIO6 GPIO12 GPIO5 CE1. Port 4: GPIO21 GPIO26 GPIO20 GPIO19. Port 5: I2C(SDA, SCL) GPIO18 GPIO27. Port 6: I2C(SDA, SCL) GPIO23 GPIO22. Port 7: I2C(SDA, SCL) GPIO24 GPIO25. Port 8: I2C(SDA, SCL) GPIO13 GPIO16..
  • 2x20pin expansion pin header, pin height 10mm/0.39".
  • Packing list: 1x RJ45 breakout board, 4x brass standoffs, 8x M2.5x6 screws, 8x pin jumpers. (the item not include Raspberry Pi, RJ45 cable and plug).
Check Stock

ACEIRMC 2pcs ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 with Camera Module OV2640 2MP for Arduino (4pcs)

  • The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core.
  • ESP32-CAM WiFi Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card.
  • Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
  • Support OV2640 and OV7670 cameras, built-in flash.
  • Support image WiFi upload and Support TF card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module.
Check Stock

Yahboom Raspberry Pi Pico RP2040 Microcontroller Chip MicroPython Programmable IO(1 pcs)

  • From controlling appliances to operating a light display, Raspberry Pi Pico puts the technology that underpins countless everyday operations into your hands..
  • Programmable in C and MicroPython, Pico is adaptable to a vast range of applications and skill levels, and getting started is as easy as dragging and dropping a file..
  • More experienced users can take advantage of Raspberry Pi Pico’s rich peripheral set, including SPI, I2C, and eight Programmable I/O (PIO) state machines for custom peripheral support..
  • Designed by Raspberry Pi, RP2040 features a dual-core Arm Cortex-M0+ processor with 264KB internal RAM and support for up to 16MB of off-chip Flash..
  • A wide range of flexible I/O options includes I2C, SPI, and — uniquely — Programmable I/O (PIO). These support endless possible applications for this small and affordable package..
Check Stock

KEYESTUDIO Automatic Smart Plant Watering Kit for Arduino, Automatic Watering System for Your Plants

  • New Flexible Microcontroller Board --- Raspberry Pi Pico is a tiny, fast, and versatile board. It's based on RP2040 chip, which features a dual-core Arm Cortex-M0+ processor with 264KB internal RAM and support for up to 16MB of off-chip Flash, flexible clock running up to 133 MHz..
  • Multi-Function GPIO Pins---It has 26 multifunction GPIO pins, including 3 analogue inputs, 2 × UART, 2 × SPI controllers, 2 × I2C controllers, 16 × PWM channels..
  • Rich Peripheral Set---A wide range of flexible I/O options includes I2C, SPI, and — uniquely —8 × Programmable I/O (PIO) state machines for custom peripheral support..
  • Multiple Software Support---Raspberry Pi Pico has rich and complete software support and community resources. Programmable in C and MicroPython. Drag-and-drop programming using mass storage over USB..
  • This kit includes a Rpi Pico with headers soldered, 3-pin yellow header,830 breadboard, Doupont wires and micro USB cable..
Check Stock

MELIFE ESP32-CAM WiFi + Bluetooth Module WiFi for ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card

  • Transmit power: 802.11b: 17+/-2 dBm (@11Mbps), 802.11g: 14+/-2 dBm (@54Mbps), 802.11n: 13+/-2 dBm (@MCS7).
  • Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
  • Support OV2640 and OV7670 cameras, built-in flash.
  • Support image WiFi upload and Support TF card.
  • Low-power dual-core 32-bit CPU for application processors.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Package Included: 1* ESP32-CAM Module, 1* Camera Module.
  • Operating Temperature: -20 -- 85 degree celsius.
Check Stock

Treedix JST Female Connector Breakout Board 4 Channel Mux MultiPort Pitch 1.0mm for JST Male Plug

  • Upgraded from the original basis, MultiPort has multiple connection ports.
  • You can use it as a hub to add I2C devices to the bus as you need, including mounting holes, so the board can be fixed to any system.
  • There are 4pcs 1.00mm 4-pin female connectors and Mounting Points.
  • All boards that support 1mm pitch 4-pin JST connector, which can reduce the required PCB space..
  • To make using this multiplexer easier, all communication is done via I2C using our convenient Qwiic system..
Check Stock

SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V

  • Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
  • 3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
  • The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
  • I2C communication uses an open drain signaling, so there is no need to use level shifting..
  • The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
Check Stock

ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire

  • ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
  • FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
  • This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Check Stock

DORHEA 2Pcs BME280 5V Temperature Humidity Atmospheric Barometric Pressure Sensor Module GY-BME280-5V IIC I2C Breakout Board

  • The BME280 sensor is a precision sensor, is soldered onto PCB, not only the pressure and the temperature, this sensor can measure humidity..
  • BME280 5V uses both I2C and SPI (supports 3-, 4-wire SPI) interface. Interface: I2C (up to 3.4MHz).
  • Temperature humidity module is great for all sorts of weather sensing and can even be used in both I2C and SPI. for simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI..
  • The BME280 stmospheric pressure sensor is made up of a very accurate pressure sensor and an associated temperature sensor which helps calibrate the pressure readings..
  • The BME280 sensor is precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with ±1 meter accuracy..
Check Stock

AITRIP D1 Mini WiFi Dev Board,Mini NodeMcu Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 6)

  • （pack of 6 ）This D1 mini module is a mini WIFI board based on ESP-8266EX..
  • Our D1 mini development board is 100% compatible with Arduino WeMos and can be programmed in Compatible with Arduino IDE..
  • Support OTA on line.Compatible withArduino compatibility. Using Compatible with Arduino IDE for programming..
  • This WLAN board contains 11 digital input / output pins, all pins have interrupt / pwm / I2C / 1-wire and a micro-USB connection..
  • 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB connection.
Check Stock

ACEIRMC 3pcs IIC I2C TWI Serial LCD 2004 20x4 Display Screen Blue + IIC I2C Module Interface Adapter for Raspberry Pi Arduino (Blue)

  • The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures.
  • LCD2004+I2C 2004 20x4 2004A Blue/Green screen HD44780 Character LCD /w IIC/I2C Serial Interface Adapter Module for arduino.
  • It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
  • Compatible with all devices with I2C interfaces, such as for Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
  • please check which chip you have on i2c interface. (Before you upload the code to the control board, please download the LiquidCrystal_I2C library).
Check Stock