Top High Power Attenuator Reviews

Boealzhl 2W SMA DC-6GHz Coaxial Fixed Attenuators Frequency 6GHz SMA Fixed Connectors (20DB)

Useful in a wide variety of applications including impedance matching and level control..
With diffrent attenuation values of fixed attenuator to be chosen from. High quality, rugged construction..
Suitable for microwave equipment, electronic equipment or communication systems. The use of features frequency bandwidth, low standing wave, power, stable performance..
Coaxial Fixed Attenuator ONLY,other accessories demo in the picture is not included..

Useful in a wide variety of applications including impedance matching and level control..
With diffrent attenuation values of fixed attenuator to be chosen from. High quality, rugged construction..
Suitable for microwave equipment, electronic equipment or communication systems. The use of features frequency bandwidth, low standing wave, power, stable performance..
Coaxial Fixed Attenuator ONLY,other accessories demo in the picture is not included..

【IRF Tube】Using IRF series transmitting tube to ensure its being durable & can be used to connect to an antenna (instrument base)..
【Lightweight&Cost-saving】The original QCX circuit is greatly simplified, and the installed components are reduced by 50 percent to save you the trouble of complicated transformer windings and wiring procedures..
【Less Power Consumption】Thanks to the EER transmitter E-level, it boasts high power efficiency and no bulky heat sink is required..
【DSP Function】Automatic gain control (AGC), noise reduction (NR), voice trigger, voice trigger Xmit (VOX), RX attenuator attenuator (ATT), TX noise gate, TX driver control, volume control, dBm/S-meter..
【Quality Material Handling】Laser marking aluminum laser, aluminum knobs with translucent silicone buttons..

Measuring power range -75 ~ +16 dBm (external RF attenuator can be extended to 100dBm).

Useful in a wide variety of applications including impedance matching and level control..
With diffrent attenuation values of fixed attenuator to be chosen from. High quality, rugged construction..
Suitable for microwave equipment, electronic equipment or communication systems. The use of features frequency bandwidth, low standing wave, power, stable performance..
Coaxial Fixed Attenuator ONLY,other accessories demo in the picture is not included..

【Connector Type】 20dB attenuation amount, FC-APC Female to FC-APC male attenuator, adopting high performance attenuated fiber.
【Operation Wavelength】This attenuator is suitable for both 1310nm and 1550 nm single mode fiber connection.
【High Attenuation Precision】 Attenuation precision: ±10%, when connector attenuation amount003e5dB.
【Transmission Stability】 Reflectance: dB≥50, which ensures the optical power stay in a stable level on its original transmission wave..
【Easy Installation】 The simple and compact structure make it very user friendly, just need plug and play for installation.
【Product Application】 Widely used in the fiber optic communication system, for example, optical instrument calibration or fiber signal attenuation etc..

Large Range: The measuring power range of this RF power meter is -60～-5 dBm (External RF attenuator can be extended to 100dBm), and the frequency range is up to 8000MHz..
Specific Feature: The RF power meter is light, compact and convenient, with a measurement power resolution of 0.1 dBm, and an output interface SMA_K..
Clear Display: This RF power meter comes with an LED screen, the data is clear and straightforward, and it is easy to use..
Standard Structure: The precise mechanical structure of the RF power meter makes the measurement accurate, convenient and reliable..
Quality Assurance: The RF power meter has been inspected many times before it leaves the factory to confirm the quality..

Choose between Eurorack power, FRACK power (panel is still Eurorack format), or 9V battery/wall plug.
Coarse & fine clock adjustment - Switchable linear 'random' function with speed adjustment - Momentary & Hard Hold Function - Manual Step Button - Internal/External Clock Switch - Reset Input Jack - Current draw is 20mA - Size: 3U 20HP - Module depth (Eurorack version): 1.5 inches.
3 CV Outs, each with their own attenuator, 0-5 volt output..

20:1 OSCILLOSCOPE PASSIVE ATTENUATOR: Can be used with most oscilloscopes to measure injector and primary ignition waveforms. Note that this attenuator should not be used for any high pressure measurements other than injectors and primary igniters.
PASSIVE 20:1 ATTENUATOR: If input 20V signal, it can output 1V signal. Since the signal is attenuated, using this project, the oscilloscope can measure voltages above its range (±20V).
MEASUREMENT RANGE: Due to signal attenuation, using this item, the HT201 attenuator can measure voltages above its range (±20V).
PRODUCT FEATURES: It provides enhanced input overload protection when used in oscilloscopes to measure inductive signals, such as nozzles and primary ignition. Do not use it for secondary ignition tests.
AFTER SALES & SERVICE: If for some reason you are not satisfied with your purchase, damaged, damaged in shipping or even changed your mind. Please feel free to contact us, we will be happy to answer your questions.

This is an RF power meter, which is operated by buttons..
Advantages: simple structure, convenient use, stable performance, reliability, high sensitivity and fast measurement speed..
Application: RF power measurement, instrument calibration.
Measuring power range: -50~+0 dBm (external RF attenuator can be extended to 100dBm).

Attenuation Factor and Step Size :The HMC472 is a wideband 6-bit digital attenuator with an attenuation range of 0 to 31.5 dB and a typical step error of ± 0.25 dB..
Operating Frequency Range :Adopt QFN surface mount package, uses single power supply 5V, working frequency range from DC to 3.8 GHz..
Insertion Loss :Insertion loss is less than 2.0 dB (typical) and IIP3 is +54 dBm..
Objects Used :Suitable for a variety of RF and IF applications..
Attenuation Control Interface :Manually adjust the control through the 6-position pin header on the board..

Can be built with FRACK power (panel is still Eurorack format), or 9V battery/wall plug.
3 CV Outs, each with their own attenuator, 0-5 volt output..