Top Hidden Deck Fastener Gun Driver Reviews

Myard Universal Hidden Deck Fastener Clips for Grooved Edges of Composite Decking Boards to Joists, 1/4' Gap Spacing, with Square Driver Bit (100-Pack)

▼ Compatible with AZEK, Cali-Bamboo, Deckorators, DuraLife, Envision, EverNew, Fiberon, MoistureShield, Lumberock, TimberTech, Trex, WearDeck, Zuri branded edge-grooved composite, hardwoods, treated lumber, cedar, & vinyl deck boards..
▼ INSTALLATION: (1) Insert a Myard hidden fastener clip into the grooved edges of decking over a joist. (2) Drive the screw ONLY halfway (Fully tighten later once all boards are in place). The wings must remain level with the joist for the next board to fit correctly. (3) Continue to add clips on each joist against deck boards..
▼ INSTALLATION: (4) Install “next” boards, make sure boards are pressed firmly against the clips and secured under the wings. (5) Do NOT over-tighten the screws. Please set proper driver torquing (2 to 6 drill power). The screw head will be resting on the top of the clip, but not sinking into the clip..

Check Stock

DeckWise (Black) Ipe Clip EXTREMEKD Hidden Deck Fasteners, 1/4' Spacing, Stainless Steel Black #8x2' Trim-Head Screws for 600 Sq. Ft. of KD Hardwood, Thermal or Composite Decks (1050 Bucket)

Kit includes 1050 BLACK hidden deck clips, 1140 #8×2” black T15 stainless steel screws, driver and drill bits plus gap spacer tools.
1050 count kits will fasten 600 Sq. Ft. of decking (16″ on Center).
Use with pre-grooved 5/4 or 1x hardwoods, composites and PVC material.
Stainless Steel Insert molded inside the deck fastener prevents overdriving of the Screw during installation.
Spacer leg automatically sets the gap between boards for consistent spacing.

Check Stock

DeckWise (Brown) Ipe Clip Extreme Hidden Deck Fasteners, 3/32' Spacing, Includes Stainless Steel Black #8x2' Trim-Head Screws for 600 Sq. Ft. of AD Hardwood or Thermal Wood Decks (1050 Bucket)

Kit includes 1050 BROWN hidden deck clips, 1140 #8×2” black T15 stainless steel screws, driver and drill bits plus gap spacer tools.
1050 count kits will fasten 600 Sq. Ft. of decking (16″ on Center).
Use with pre-grooved 5/4 or 1x hardwoods, composites and PVC material.
Stainless Steel Insert molded inside the deck fastener prevents overdriving of the Screw during installation.
Spacer leg automatically sets the gap between boards for consistent spacing.

Check Stock

DeckWise (Brown) Ipe Clip Extreme Hidden Deck Fasteners, 3/32\ Spacing, Includes Stainless Steel Black #8x2\ Trim-Head Screws for 300 Sq. Ft. of AD Hardwood or Thermal Wood Decks (525 Bucket)

Kit includes 525 BROWN hidden deck clips, 570 #8x2” black T15 stainless steel screws, driver and drill bits plus gap spacer tools.
525 count kits will fasten 300 Sq. Ft. of decking (16" on Center).
Use with pre-grooved 5/4 or 1x hardwoods, composites and PVC material.
Stainless Steel Insert molded inside the deck fastener prevents overdriving of the Screw during installation.
Spacer leg automatically sets the gap between boards for consistent spacing.

Check Stock

Max HN120 PowerLite Concrete Nailer

✅ Shoots 14 gauge T-nails from 5/8'' to 2-1/2'' long | Hardened driver | Convenient side-load magazine | Rubber hand grip for added comfort | Heavy-duty light weight aluminum body | Adjustable exhaust.
✅ Soft grip handle reduces fatigue | Touch-strike security system is safe for the operator | Available with either sequential and contact fire trigger | Quick-release nosepiece for fast clearing of jams | Rubber can protect the surface of the gun when the gun fall.
✅ Magazine Capacity: 100 | Operating Pressure: 80-100 PSI | Air Inlet: 1/4" | Fastener Size: 14 Gauges - 0.087" Diameter | Fastener Type: T-Nails (both hardened & galvanized) | Fastener Length: 5/8" - 2-1/2" Long Nails.
✅ Includes: Concrete T-Nailer | Cardboard box.
✅ Wood to concrete & masonry furring | Plywood to concrete nailing | Light gauge steel drywall track to concrete | Wire lath to masonry | Steel banding to wood | Wood to light gauge steel (up to 3/16") | Decking | Fencing | Sub flooring | General construction.

Check Stock

DEWALT Drywall Screw Gun, Variable Speed Reversible, 6.5-Amp (DW276)

Drywall screw gun has helical-cut steel and heat-treated gears for long life and durability.
DEWALT drywall screw gun has a high torque for deck building, drywall and heavy gauge steel stud framing.
The drywall gun has metal gear housing for jobsite durability and increased reliability.
Depth-sensitive, "set and forget" nosepiece for consistent fastener depth.
Two-finger trigger for increased comfort and ease of use.
Excellent ergonomics offers less user fatigue.

Check Stock

DeckWise (Black) Ipe Clip Extreme S Hidden Deck Fasteners, 5/32' Gap, Stainless Steel Black #8x2' Trim-Head Screws for 300 Sq.Ft. of AD and KD Hardwood, Thermal or Composite Decks (525 Bucket)

(570) #8×2″ T15 Stainless Steel Screws.
Automatically spaces deck boards at 5/32″ (4mm).
Manufactured from polyethylene with stainless steel black oxide insert.
Reduces fastener tilting during installation improving gap consistency.
For use with air/kiln dried hardwood, composite, or PVC decking.

Check Stock

CAMO Drive Collated Edge Deck Screws 2-3/8 ProTech 1000 ct

For use in 1" and 2x (1-1/2") thick treated lumber, composite, capped composite, or PVC decking.
Edge Deck Screws install through the edge of the deck board, leaving a fastener-free surface.
Rake tip augers material out, Trimhead reduces visibility on edge, ProTech coating is ACQ Compatible.
1000 ct package covers approximately 285 sq ft (joist spacing of 16 inches). Two(2) driver bits included.
Use exclusively with CAMO DRIVE: the stand-up deck fastening tool that makes installation 5X faster.

Check Stock

NATIONAL NAIL 345001 Marksman Pro Tool

Tool used in conjunction with screws and bit.
Provides a low cost, fastener free deck surface.

Check Stock

CAMO Drive Collated Edge Deck Screws 2-3/8 Stainless Steel 1000 ct

Use in 1" and 2x (1-1/2") thick wood, composite, capped composite, or PVC decking in areas near open water.
Edge Deck Screws install through the edge of the deck board, leaving a fastener-free surface.
Rake tip augers material, Trimhead reduces visibility on edge, 316 Stainless Steel resists corrosion.
1000 ct pkg covers approximately 285 sq ft (joist spacing of 16 inches). Two(2) driver bits included.
Use exclusively with CAMO DRIVE: the stand-up deck fastening tool that makes installation 5X faster.

Check Stock

Concrete Nail Gun, Silencer Shot Nail Grab, Steel Nails Gun, Portable Nail Gun Set, Concrete Nailer With Case, Manual Fastening Tool for Cement Wall

✅ Shoots 14 gauge T-nails from 5/8'' to 2-1/2'' long | Hardened driver | Convenient side-load magazine | Rubber hand grip for added comfort | Heavy-duty light weight aluminum body | Adjustable exhaust.
✅ Soft grip handle reduces fatigue | Touch-strike security system is safe for the operator | Available with either sequential and contact fire trigger | Quick-release nosepiece for fast clearing of jams | Rubber can protect the surface of the gun when the gun fall.
✅ Magazine Capacity: 100 | Operating Pressure: 80-100 PSI | Air Inlet: 1/4" | Fastener Size: 14 Gauges - 0.087" Diameter | Fastener Type: T-Nails (both hardened & galvanized) | Fastener Length: 5/8" - 2-1/2" Long Nails.
✅ Includes: Concrete T-Nailer | Cardboard box.
✅ Wood to concrete & masonry furring | Plywood to concrete nailing | Light gauge steel drywall track to concrete | Wire lath to masonry | Steel banding to wood | Wood to light gauge steel (up to 3/16") | Decking | Fencing | Sub flooring | General construction.

Check Stock

Start Clips - Universal Starter Deck Clips, Start Clips for Decking, Hidden Fasteners & Deck Starter Clips with Decking Screws (36 Pack, Black)

【Characteristic】 Start clips are specially used to install perimeter deck boards to make the installation of grooved composite deck easier. Hidden starter clips provide you a high-quality solution and a clean and fastener-free deck appearance..
【Material】 The start hidden fasteners made of high-quality stainless steel have strong corrosion resistance and are very suitable for indoor and outdoor use. The starter clips have high strength and perfect toughness, which can improve the installation efficiency greatly and have a better fastening effect on the deck..
【Contents】 You will get 36 high-quality start clips, 38 stainless screws and 1 drive bit. Adjust the installation method according to actual usage requirements, and place a decking clip every 12 to 16 inches..
【Application】 It is recommended to install the universal starter deck clips on the center edge of the joists, align the back of the deck starter clips on the same edge and fix them with screws, and then you can push the first board into the starter clips gently..
【Service】 We provide you with 100% return and 24-hour friendly customer service. If you are disappointed with this start clips, we can exchange them for free or give you a full refund..

Check Stock

CAMO Marksman Pro Kit Deck Tool 1750 Edge Screws & Bits Edge Fastening Installation 3/16 Spacing Fits 5-1/4-5-3/4 Composite Decking 0345001 …

ALL IN ONE KIT - Marksman PRO Tool, (1750) 2-3/8" Edge Screws (covers approx 500 sqft) and 2 replacement driver bits..
FASTENER FREE DECK SURFACE - installs two patented CAMO Edge Deck Screws through the edge of the deck board—not the surface—for a beautiful deck top.
AUTOMATIC SPACING - creates automatic 3/16 in. (5mm) spacing - ideal for composite and PVC decking.
COMPOSITE AND PVC DECKING - Fits any 5-1/4 in. (133mm) to 5-3/4 in. (146mm) deck board.
REDUCE SPLITTING & CRACKING - For exclusive use with CAMO Edge Deck Screws that auger material out to reduce splitting and cracking.

Check Stock