Top Glass Tube Flow Meter Reviews

Argon/CO2 Flow Meter Gas Regulator Compatible with Mig Tig Welder Regulator with 6.6FT Gas Hose 10 to 60 CFH Output Flow 0 to 4000 PSI - CGA-580 Inlet argon flow gauge welding regulator

...rdy and durable, which can withstand harsh environments and have a longer life. Came with 6.6 Ft argon welding gas regulator hose and protective cover are made of impact-resistant composite material for safety and durability.
【Wide Application】Idea choice for CGA 580 Tank Fitting. This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet). So it will screw right into the Argon, Argon/CO2 tanks. IDEAL FOR Miller, Lincoln, Hobart, HTP, and most other welders! Idea choice for MIG TIG welding, cutting ,chemical and electronics industry.
【Accurate Gas Flow Gague】Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube. 0-4000psi inlet pressure, easy-to-read bottle pressure gauge included, allowing you to view how much gas is left in the tank range 0 to 4000psi. Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting. It also comes with a standard 1/4" barbed fitting.
【Good Design】Use economic style flow meter regulator and single stage piston design, combination of regulator and flow meter as one unit, compact lightweight construction, convenient for use. Argon Regulator is a ideal choice for professional TIG/MIG welding applic....

Check Stock

Allturn Argon CO2 Mig Tig Flow meter Welding Weld Regulator Gauge Gas Welder CGA-580 With 80 6.6FT Hose

✅The Square flow tube reads from 0 - 60 CFH ,which is indicated by a ball which moves up and down in the flow tube.And has large 1 1/2" diameter....
✅Argon / CO2 regulator and flow meter..
✅INLET - CGA580 Bottle Connection for argon and argon, CO2, and helium blend bottles.
✅OUTPUT - Two Female 9/16" x 18 nut and male 5/"8 UNF-18RH fitting and a standard 1/4" barbed fitting..
✅100% HIGH QUALITY AND STURDY - Flowmeter regulator is made of high quality brass and came with 6.6 Ft argon regulator Hose.

Check Stock

BETOOLL HW9003 Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Welding Weld

Brand New BETOOLL Argon / CO2 regulator and flow meter..
Flow Meters are more accurate than the flow gauge regulators..
The pressure gauge which shows how much gas is left in the tank goes from 0 to 4000 psi..
And this flowmeter does not use a diaphragm, so it is more reliable than the flow-gauge style regulators..
The output flow is adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube..

Check Stock

AWLOLWA Argon CO2 Mig Tig Flow meter Welding Weld Regulator Gauge Gas Welder CGA-580 With 80'' (6.6FT) Hose

INLET - CGA580 Bottle Connection for argon and argon, CO2, and helium blend bottles.
OUTPUT - Female 9/16" x 18 nut and male 5/"8 UNF-18RH fitting.
The Square flow tube reads from 0 - 60 CFH ,which is indicated by a ball which moves up and down in the flow tube.And has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI. Easy to Read, Accurate.
100% HIGH QUALITY AND STURDY - Flowmeter regulator is made of high quality brass and came with 6.6 Ft argon regulator Hose.

Check Stock

TERA PUMP | 4.5 GPM Electronic 35L Metered Pail Transfer Pump Flow Control Nozzle 16.5 in 22.6 in Intake Tube Fits 5 Gallon Pail Buckets Engine Oil Hydraulic Fluid DEF Gas Diesel AG Chemicals

Flow Rate of 4.5 Gallons/ Minute with Engine Oil (1.4 GPM) Hydraulic Fluid DEF Gasoline Diesel AG Chemicals Washer Fluid Antifreeze.
Suction Tube is Adjustable to 16.5 in to 22.6 in | Flexible Discharge Hose: 6 foot with Flow Control Nozzle.
Transfer Liquid to Cars, Boats, Tractors, ATV/UTV, Generators, Snowmobiles etc..
Precise Flow Rate with 35L Digital Oil Meter with LCD Display.
Pump, Meter, Pail Lid, and Power Adapter are Included.

Check Stock

4PCS Clear Glass Tube Adapters 14mm Oil Lamps

High quality material. The lily tube outflow is made of high-quality borosilicate glass. Durable, safe, non-toxic and easy to clean..
Elegant Appearance: The glass transparency gives your aquarium a gorgeous look. It will create an elegant curve in your aquarium..
Size: Slowed down the flow of water. Let the water flow smoothly. The lily tube effluent delivers clean water from the filter at the proper water flow rate. The smooth poppy shape helps the water flow smoothly..
Packaging and Service: We do our best to make the product you receive complete. If you have any questions, please feel free to contact us. We will give you a satisfactory answer..

Check Stock

Vehicle Maintenance Log Book: Easy-to-use Vehicle Service and Repair Record Book

Flow Rate of up to 7.1 Gallons with the Included 110V DC Plug-In Adapter, Plug-In Pump, Flip the Switch and Squeeze the Trigger to being the Flow.
Compatible with Engine oil, Hydraulic fluid, DEF, Diesel, Kerosene, Washer Fluid, Antifreeze, Non-Potable Water and more.
Discharge Hose Length of 6.6 ft with Flow Control Nozzle / Adjustable Intake Tube Reaches from 2.8 ft to 4.1 ft to fit 55 Gallon Drums to IBC Totes.
Digital Oil Meter - 35L Flow Rate of Low Viscosity Fluids.
Backed by a 1 Years Limited Manufacturer Warranty on Defects / Do Not Use with Chlorinated Acids or Drinking Water.

Check Stock

Horiba 9096001700 Plastic Body PH Electrode

Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..

Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..

Check Stock

RX WELD Argon Mig Tig Flow Meter Gas Regulator Gauge with Gas Hose Welding Weld

1.VERSATILE APPLICATIONS FOR CGA-580 Tanks: This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet).
2.Accurate Gas Flow Gague：Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube..
3.RELIABLE QUALITY - Our argon flow meter's body is made of high-quality brass, which can withstand harsh environments..
4.OUTPUT:Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting..
5.Hose Included: RX WELD 6.6Ft Hose Quick Connect Fitting enable your tanks at a safe distance from your welding projects..

Check Stock

CGOLDENWALL Turbine Flow Meter Digital Fuel Flowmeter with FNPT Inlet/Outlet, 1inch Flow Meter for Water Diesel Kerosene Gasoline, 2.5-26GPM /9-100LPM (1 inch)

FLOW METER: the 1 inch flow meter can read instantaneous flow rate, single cumulative flow and total cumulative flows. But it has minimum flow rate requirment, if the flow rate of the tested liquid is lower than 2.5 gal/min, the readings will be inaccurate..
TECHNICAL PARAMETERS：① diameter of water inlet: 32mm.
③ the flow speed requirenment for tested liquid: 2.5~26 gal/min.
⑥ max temp of tested liquid: 158°F/70°C.
MULTIPLE UNITS: the flow meter provide 4 meauring units for option, which are liter, gallon, pint and quart. The unit defaults to gallons, if the unit is not gallons, please refer to the user manual to change the unit to the needed one..
NOT WATER PROOF: the flow meter is not water proof, please keep the display from water during use, to avoid chip damage. We upgraded The flowmeter has been upgraded from never-sleep model to auto-sleep model, which automatically dims the screen when no liquid is flowing through it..
WIDE APPLICATION: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids. If there is any problem, please contact us in time..

Check Stock

RX WELD Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Welding Weld

1.VERSATILE APPLICATIONS FOR CGA-580 Tanks: This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet).
2.Accurate Gas Flow Gague：Adjustable from 10 to 60 cfh (cubic feet per hour), and is indicated by a ball which moves up and down in the flow tube..
3.RELIABLE QUALITY - Our argon flow meter's body is made of high-quality brass, which can withstand harsh environments..
4.OUTPUT:Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting.It also comes with a standard 1/4" barbed fitting.
5.DESIGNED and PERFECT for MIG and TIG Welding Applications. Our Flowmeter is an economic alternative for the demanding customers who wants more precise gas metering..

Check Stock

Argon Regulator Dual Co2 Flowmeter by Manatee for TIG MIG Welder Gas and backpurge 60 SFCH - CGA 580 inlet connection and 5/8 x 18RH outlet fitting - Accurate Gas Metering Delivery System

✔ WHETHER YOU ARE a welding beginner or a seasoned professional, you will surely enjoy using the Argon Regulator Dual Flowmeter! Perfect for hooking....
✔ COMPATIBLE with a range of gases, including CO2 as well as argon, and designed to reduce and control pressure levels, this MIG TIG Welding Argon....
✔ DESIGNED and PERFECT for MIG and TIG Welding Applications. Our Flowmeter is an economic alternative for the demanding customers who wants more....
✔ HAS CGA - 580 Tank fitting so it will screw right into the Argon, Argon/CO2, and Helium Tanks. The Square flow tube reads from 0 - 60 CFH and has....
✔ Welders around the nation agree that the Argon Flow Meter Regulator is key to accurate gas meter readings..

Check Stock