Top Fluted Hand Tool Reviews

Drill America - DWDA/CX127/64 7/64\ x 12\ High Speed Steel Aircraft Extension Drill Bit, DWDA/C Series

  • High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
  • Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.
  • Round shanks allow use with a wide variety of tool holding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to national aerospace standard 907.
Check Stock

Drill America - DWDA/CX61/8 1/8' x 6' High Speed Steel Aircraft Extension Drill Bit, DWDA/C Series

  • High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
  • Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.
  • Round shanks allow use with a wide variety of tool holding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to national aerospace standard 907.
Check Stock

Drill America 1 High Speed Steel 3MT Taper Shank Drill Bit DWDTS Series

  • High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
  • Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.
  • Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Designed to perform in a broad range of materials in the iron and steel families.
Check Stock

KEO 34140 Solid Carbide High Performance NC Spotting Drill Bit TiN Coated Round Shank Right Hand Flute 90 Degree Point Angle 1/4 Body Diameter 2-1/2 Overall Length

  • Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.
  • Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Right-hand cut tools have a cutting action that engages when they are run in a clockwise direction.
Check Stock

KEO 34180 Solid Carbide High Performance NC Spotting Drill Bit, TiN Coated, Round Shank, Right Hand Flute, 90 Degree Point Angle, 1/8\ Body Diameter, 1-1/2\ Overall Length

  • Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.
  • Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Right-hand cut tools have a cutting action that engages when they are run in a clockwise direction.
Check Stock

Drill America 1-1/4 3MT High Speed Steel Undersized Shank Taper Shank Drill Bit DWDTS Series

  • High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
  • Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.
  • Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Designed to perform in a broad range of materials in the iron and steel families.
Check Stock

Drill America #43 Solid Carbide Drill Bit, DMOD Series

  • Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.
  • Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to National Aerospace Standard 907.
Check Stock

General Tools Scratch Awl Tool with Hardwood Handle - Scribe, Layout Work, & Piercing Wood - Alloy Steel Blade

  • WOODEN HANDLE AWL: Our craft piercing tool is rust-resistant and can be used for punching, screwing holes, scribing, and perforating wood. It features a sharp point and a contoured and fluted wooden handle used by carpenters and other artisans..
  • CRAFT AWL: This handy needle tool can help you create your next woodworking masterpiece. Drag the tip of the awl along the grain of the wood, creating a shallow groove, reducing the chances of the hand saw or chisel from wandering across the board..
  • AWL PUNCH: The hand-held tool features a steel blade through the grip and is fastened to a plated steel ferrule and cap. Awls with rounded points can mark the location of holes that will later be made more prominent with a hole punch..
  • MARKING AWL: It only takes a few seconds to use an awl scratch to make a starting point for a drill bit, which is much less time than it would take to sand out any damage. Our pocket awl can withstand heavy pressure and challenging workloads..
  • GENERAL TOOLS: We're a recognized leader in designing and developing specialized precision tools dedicated to delivering exceptional customer service. We encourage artisans and DIYers to work smarter, measure better, and repair more productively..
Check Stock

Drill America - MMO11/64-4FSE 11/64\ Carbide 4 Flute Single End End Mill, MMO Series

  • Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Check Stock

Qualtech 26.00mm HSS 3MT Metric Taper Shank Drill Bit, DWDTSMM26.00

  • High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
  • Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Check Stock

Topline #44 Wire Size HSS Drill Bit 6pcs Bright Finish M2 Grade

  • Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.
  • Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to National Aerospace Standard 907.
Check Stock

Qualtech 1-1/2\ HSS 4MT Taper Shank Drill Bit, DWDTS1-1/2

  • Cobalt taper shank drills are made of heat resistant cobalt..
  • Engineered with heavy-duty construction to perform well in tough, hard-to-machine materials..
  • Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Designed to perform in a broad range of materials in the iron and steel families.
Check Stock

Ravioli Cutter Stamp Maker and Pasta Roller Wheel Cutter Set, Round Square Shape Fluted Press Mold with Wooden Handle, for Kitchen Ravioli Machine

  • These ravioli makers cutters made of food-grade aluminum fluted frame cut, high-quality wooden handles offer a firm grip. Further comfortable for users to make large batches of the ravioli..
  • Ravioli stamp cutter package includes 1 square cutter, 2 round cutters, and 1 roll wheel cutter. Which allow you to create variety shape consistent ravioli..
  • The ravioli cutter wheel is hand-rolling to cut the rolled out dough and width you want. Also ensures that separate the ravioli shapes and pieces before your cooking begins. Measure approx is 5.1 by 2.8inch..
  • Great for cutting and sealing homemade meat, cheese or lobster filled ravioli. Easy to maintain and use, by hand clean and dishwasher safe. please let ravioli tools dry out before storage..
  • The ravioli tool set is a great additional tool to your kitchen! If you are unsatisfied with the purchase, please directly via Amazon to contact us, we will take care of you within 24 hours!.
Check Stock