Top Fitting Ferrule Reviews

Stainless Steel 316 SS316 Sanitary Fitting Diameter 51MM 2 Weld Pipe with 64MM Ferrule Flange fits 2 Tri Clamp

Stainless steel 316 for resistance to corrosion and high temperatures.
Maximum operating pressure rating of 250 psi at 70 degrees F ambient temperature.
Ferrule fitting for providing a seal when compressed between two mating components.
Attaches to a fitting to help provide a leak-resistant seal on a tube or hose.
This long weld clamp ferrule sanitary fitting is suitable for use in food, beverage, and dairy applications.

Check Stock

Parker A-Lok 4NU4-B Brass Compression Tube Fitting, Nut, 1/4\ Tube OD

Nut tightens and provides compression on the ferrule of a flareless fitting.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
For use with a twin ferrule compression fitting set for a leak-resistant seal in high-pressure applications.

Check Stock

Parker A-Lok 8NU8-316 316 Stainless Steel Compression Tube Fitting, Nut, 1/2\ Tube OD

Nut tightens and provides compression on the ferrule of a flareless fitting.
Chemically hardened type 316 stainless steel for higher strength and greater corrosion resistance than untreated stainless steel.
For use with a twin ferrule compression fitting set for a leak-resistant seal in high-pressure applications.

Check Stock

DERNORD Tri Clamp Bowl Reducer Sanitary Fitting Stainless Steel 304 (Tri Clamp Size: 4 inch x 2 inch)

Bowl Reducer fitting to connect two pipes of different diameters that are along the same pipe axis.
Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access.
Stainless steel 304 for resistance to corrosion and high temperatures.
Tri Clamp Bowl Reducer Ferrule Size 119MM fits 4" tri clamp.
Tri Clamp Bowl Reducer Ferrule Size 64MM fits 2" tri clamp.

Check Stock

Compression Sleeve Puller Tool Remove Nut & Ferrule Of Pipe 03943, Sleeve Remover For 1/2” Compression Fittings Only, Corroded & Frozen Supply Stops, Plumbing Tools Compression Ring Removal Tool

...ssion sleeve puller removes leaking compression sleeves without damaging walls, which effortlessly pulls the nut and ferral off of the pipe. This sleeve remover removes 1/2-inch copper water compression sleeve. If you are in need of replacing a quarter turn valve on a dishwasher, sink or toilet that has compression fittings, buy this sleeve remover tool and make your life easy. Precision machined plumbing tool..
【Not Need To Cut Off The Pipe】Saves a lot of time around cutting old pipes. This puller tool is easy to use in relatively tight spots. Especially if you don’t have sufficient exposed copper to cut off the old compression fitting, this angle stop puller will effortlessly remove the old compression ring and reform the previously crimped copper pipe back to a perfect circle. No damage to the copper. Makes removing a nut and ferrule simple, and makes plumbing work simple..
【Work On Corroded & Frozen】Fully machined body and screw, this ferrule puller is durable, corrosion resistant & wear resistant. Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe..
【Easy & Fast Remove】1.Remove the old compression fitting or the old angle stop. 2.Put the nu....

Check Stock

Beduan Brass Compression Fitting, Insert Tube Support Compression Sleeve Fitting 1/4\ Tube ID (Pack of 10)

...ade of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing.....

Check Stock

Hilitchi 8Sizes Tube OD 4mm-16mm Brass Compression Sleeves Ferrules Compression Fitting Kit Metric 220Pcs

...de of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
✅ [FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅ [HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅ [APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubin....

Check Stock

Hilitchi 3Sizes Tube OD 1/4 5/16 3/8 Brass Compression Sleeves Ferrules Compression Fitting Kit (SAE, 105Pcs)

...ade of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing.....

Check Stock

DERNORD Sanitary Concentric Reducer Tri Clamp Clover Stainless Steel 304 Sanitary Fitting End Cap Reducer (Tri Clamp Size: 2 inch x 1.5 inch)

Concentric reducer fitting to connect two pipes of different diameters that are along the same pipe axis.
Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access.
Stainless steel 304 for resistance to corrosion and high temperatures.

Check Stock

1/4\ 0.25\ double ferrule for compression Tube Fittings, Stainless Steel 304 (Pack of 10 PCS)

Fit 1/4" OD stainless steel tube double ferrule compression tube fitting.

Check Stock

uxcell Stainless Steel Compression Tube Fitting 1/2 NPT Male x 1/2\ Tube OD

【1/2 NPT MALE x Ф1/2 TUBE OD】Tube OD : 12mm(1/2").
【DOUBLE FERRULE】This fitting has a double ferrule construction,reducing the possibility of leakage.
【NO NEED TO WELD】It does not need to be welded when it is connected with steel pipe, which is conducive to fire prevention, explosion protection and high altitude operation.
【SAFE & DURABLE】Strong connection, strong pressure resistance, good sealing, convenient installation and maintenance, safe and reliable operation.
【REPEATABLE INSTALLATION】All joints can be re-installed, but to ensure that the parts are not damaged and clean.

Check Stock

Litorange 3 Pack Metal Brass Compression Tube Pipe Fitting Connector, Straight Coupling Adapter, 3/8\ Tube OD x 1/2\ NPT Male

★ 【Material】: Heavy Duty Brass,strong and durable. Size: 3/8" Tube OD x 1/2" inch NPT Male Adapter..
★ 【Firm And Durable】: Litorange Brass for corrosion resistance, high temperature ductility and low magnetic permeability..
★ 【Function】: Fitting connects to tubing on one end and has an NPT male connector on the other. Use with copper, brass, aluminum, or plastic tubing..
★ 【Tips】: Single ferrule compression fitting has fewer possible leak paths than twin ferrule fittings. Primary uses water, gasoline, oil and vacuum lines..
★ 【Package Include】: 3 PCS 3/8" Tube OD x 1/2" NPT Male connector. Comes with 1 year warranty..

Check Stock

Legris 0124 10 00 Brass Compression Tube Fitting, Sleeve, 10 mm Tube OD

Sleeve of a ferrule set for providing a seal when compressed between two mating components.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Ferrule compression fitting for a leak-resistant seal.
For use with Legris 0110 brass nut (sold separately).

Check Stock