Top Ethernet Servo Board Reviews

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

  • 10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
  • Great for jumping from board to board or just about anything else..
  • There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
  • Length:100mm Type:JR Plug Servo Extension wire (Male to Male).
Check Stock

6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat

  • Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
  • This servo Y-cable allows you to control two servos with one radio channel..
  • Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
  • 3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
  • Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..
Check Stock

Arduino | Step by Step: The Ultimate Beginner’s Guide with Basics on Hardware, Software, Programming & DIY Projects (Arduino | Introduction and Projects Book 1)

  • ...t Switch, 3-Axis Accelerometer, LCD, Relay, Servo and Stepper Motor - suitable for beginner or advanced users.
  • Build wireless IoT Automation projects with ESP32 Development Board, HC-05 Bluetooth Module, ESP8266 Wi-Fi Module, 2x NRF24L01 Wireless Transceivers and the W5100 Ethernet Shield.
  • All-in-one bundle with extra accessories + 16G USB storage with free access to the GAR Dropbox Cloud including PDF guides & links to tutorials and videos to help you learn to program all the parts and get started quickly.
  • Effective technical/customer support from USA with lifetime replacement guarantee on all parts – The Monster comes in 16" x 12" durable organizer tool box for safe transport and storage. No soldering required. Please let us know about any improvements we can make to the Monster Kit. Critical feedback is much appreciated.
Check Stock

Ethernet SmoothStepper Motion Control Board with Smooth Stepper Terminal Board

  • 6 Axis Ethernet SmoothStepper Motion Control Board with Terminals control board.
  • Ethernet SmoothStepper Motion Control Board with Terminals.
Check Stock

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

  • This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
  • Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
  • Includes a total of over 190 electronic parts and components.
Check Stock

sb components Motor Driver Board for The BBC Micro bit 2 Channel DC Motors and 3 Channel Servos Motors Motor Driver for Micro bit BBC microbit Motor Driver Board

  • micro:bit edge connector, directly pluggable.
  • 2x DC motor interfaces, 3x servo interfaces.
  • Integrates 5V regulator, up to 3A output current.
  • Onboard multi connector options for DC motors in different specifications, onboard standard servo headers.
Check Stock

KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino

  • This expansion board can directly stack on the controller R3 board and can drive up to 16 servos.
  • Uses I2C input, just occupy A4 and A5 interface on the control board.
  • Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits.
  • Servo power supply independent V + input up to 6V.
  • How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product..
Check Stock

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

  • MKS servo42C is a product developed by MKS to meet market demand. The closed-loop motor uses the motor's rotation angle feedback to the drive circuit to detect whether every step that should be taken has been taken to prevent losing steps. If a closed loop occurs, the motor will make up or lose steps through the feedback information, and the blue LED on the closed loop module will light up..
  • Support 1-256 subdivision,odd subdivision (such as 11 subdivision) is also available. And support motors with 0.9 degree or 1.8 degree. Maximum speed 1000RPM. With usart interface, you can connect the computer by serial port, for parameter adjustment and query..
  • Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
  • Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
  • Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User metho....
Check Stock

Barnabas Robotics Servo Motor Tester Kit | 180 Degree 9g Servo Motor + RC Servo Tester Controller + 6V Battery Holder

  • [CONVENIENT, ALL-IN-ONE KIT FOR TESTING SERVO MOTORS] Experiment with servo motors with this all-inclusive kit. Includes 9g servo motor + servo tester controller + 6V battery holder at a low price!.
  • [9G Servo Motor] 180 degree range of motion. Includes 3 types of servo horns..
  • [4 CELL x AA BATTERY HOLDER] Fits 4 x AA batteries, which produces 6V for your servo tester and servo motors..
  • [SERVO TESTER] Includes 3 modes to test servo motors or ESC.
  • [GREAT FOR RC APPLICATIONS] Use as a power source for robotics, RC cars, helicopters, planes, boats and or any hobby projects.
Check Stock

Orange Pi Pc Plus RAM 1G AllWinner H3 Quad Core Open Source Development Board Desktop with 8GB Emmc Flash, Run Android Ubuntu Debian Single Board Computer (PC Plus)

  • Orange Pi PC PLUS adopts Allwinner quad-core A7 high-performance processor Allwinner H3, integrates Ethernet, DC power input, video/audio output and other interfaces, and supports HDMI, AVOUT video output and other functions. Note: Our shipping time generally takes 15 days, Not as long as Amazon suggests..
  • Orange Pi PC Plus RAM 1G with 8GB Emmc Flash ,Mini Open-Source Single Board,Support 100M Ethernet Port/Wifi/Camera/Hdmi/IR/MIC.
  • Orange Pi PC Plus open source development board references quite rich interfaces, including HDMI, Ethernet, USB-Host, USB-OTG, DVP camera, etc. And it integrates on-board network, on-board storage, LED indicator, and our development board is compatible with Raspberry Pi GPIO port, has a unique debugging serial port, etc..
  • Memory (SDRAM): 1GB DDR3 (shared with GPU). Onboard Storage: TF card (Max. 32GB) / MMC card slot, 8GB EMMC Flash.
  • Three USB 2.0 HOST, one USB 2.0 OTG, 40 Pins Header, Camera Interfacce, HDMI, MIC, IR Receiver.
  • Orange Pi Single Board Computers can builed a computer, a wireless server, Games, music and sounds, HD video, a speaker, Android, Scratch.Pretty much anything else, because Orange Pi is open source..
  • Notice before order: By default, we won't responsible for customs clearance fee charged by your local. If ....
Check Stock

WEISHUJI 25T Servo Horn Steering Arm, Servo Horn 25T Steering Arm, Aluminum 25T Servo Horn Steering Arm for Traxxas TRX4 Axial SCX10 Tamiya 1/10 RC Crawler Truck (Red-Black)

  • 25T Servo Horn Steering Arm fits for Traxxas TRX4 Axial SCX10, SCX10 ii 90046 1:10 scale rc crawler, and Servo Horn 25T Steering Arm is CNC machined..
  • 25T Servo Horn Steering Arm has 18mm and 22mm threaded mounting holes for adjustability, and Servo Horn 25T Steering Arm is of high quality..
  • 25T Servo Horn Steering Arm is Red-Black, and Aluminum 25T Servo Horn Steering Arm is of small size and lightweight..
  • 25T Servo Horn Steering Arm works on Futaba, Savox, Emax, HSP, Power HD, Xcore, Aluminum 25T Servo Horn Steering Arm works on other popular prand servos motor (Except Hitec and JR Servos)..
  • Package of 25T Servo Horn Steering Arm includes: 1 x 25T Servo Arm (Red-Black), Servo Horn 25T Steering Arm, Aluminum 25T Servo Horn Steering Arm.
Check Stock

SunFounder Mega 2560 R3 ATmega2560-16AU Board and Ethernet Shield W5100 for Arduino

  • The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
  • The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library)..
  • The mega 2560 comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files).This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..
  • With this Ethernet Shield, for Arduino board can be used to connect to internet. It can be used as server or client. Directly plug puzzle board, no soldering required..
  • This Ethernet Shield is directly compatible with Arduino official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network..
Check Stock