Top Def Sensor Module Reviews

MEGA 2560 Starter Kit Ultra (100% Arduino IDE Compatible) w/ Battery Holder, Sensors, Modules, Resistor kit and Components (no Supply)

...830 points ) -Dupont Cables 10 * Female-Female + 10 * Male-Female + 10 Male-Male -Cable Jumper for breadboard -6 Push Buttons with multicolored caps -Joystick Module type PS2.
-RC-522 RFID Module with white RFID Card and RFID Keychain -High-precision RTC Real-Time Clock Module DS3231 and EEPROM AT24C32 -PIR Presence Sensor HC-SR501 -Distance measurement module HCSR04 -Sound sensor detector module with programmable threshold -LM35 temperature sensor -Tilt detector module -Servo SG90 motor -Stepper motor (5V) -Motor driver module for stepper motor ULN2003.
5V Active Buzzer -5V Passive Buzzer -LCD 1602 16 characters * 2 lines -LED Display Driver MAX7219 -LED Matrix Display of 8*8 -7 Segments Display 1 digit -7 Segments Display 4 digits -Simple Relay Module - Infrared Remote Control 38kHz - 38kHz Infrared decoder receiver (type 1838) - Infrared phototransistor (Flame sensor) - Infrared LED - Light sensor (Photoresistor).
-10 * LEDs 5mm Diffused RED -10 * LEDs 5mm Diffused GREEN -10 * LEDs 5mm Diffused YELLOW -5 * LEDs 5mm Ultrabright WHITE diffused -3 * LEDs 5mm Red / Green / Blue Diffused RGB -Shift Register (Series to Parallel IC) 74HC595 - NPN Transistor BC547 - PNP Transistor BC557 - Adjustable Knob Resistor 1kOhm (Potentiometer) - Adjustable Knob Resis....

Check Stock

uxcell BWL100 100 mm Pull Rod Linear Position Displacement Sensor for Printer

Shipping list: AC 220V vibration sensor delay module, with ultra-high sensitivity vibration sensor..
AC 220V power supply ultra-high sensitivity vibration delay module plus relay module plus delay three-in-one module, vibration switch module Alarm trigger, with 1 vibration sensor. Relay does not have B1 normally closed end..
corridor delay switch, delay energy-saving products.
Supply voltage: AC 220V power supply, Current: greater than 100mA.

Check Stock

HiLetgo MEGA2560 ATmega2560-16AU Sensor Shield Sensor Expansion Board V2.0 with Bluetooth SD Card APC220 Wireless RF Ultrasonic Sensor Communication Interface

This MEGA Sensor Shield V2.0 dedicated sensor expansion board assembly market a variety of advantages in one of the expansion board design, PCB Immersion Gold processing technology..
Board not only all digital and analog interface to the steering gear line order form extended out, but also ad hoc Bluetooth module communication interface, SD card module communication interface, APC220 wireless RF module communication interface, and RB URF v1.1 ultrasonic sensor interface, independent expansion a more easy and convenient..
For beginners, do not have to worry about cumbersome and complex circuit connection, will simplify this circuit sensor expansion board in the true sense, it can often be easily connected with the sensor..
A sensor requires only a general 3P sensor cable (regardless of digital cable and analog cable), complete the circuit connection, the preparation of the corresponding program downloaded to MEGA controller reads the sensor data, or receive wireless module back pass data through the arithmetic processing, the final easy to complete your own interactive works..
Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers..

Check Stock

WayinTop 2pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 2pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
【Current Sensor Module】Chip: ACS712ELC-30A.
Pin 5V power supply, on-board power indicator.
The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
【Voltage Sensor Module】Voltage input range: DC0-25V.
DC input connector: Terminal cathode connected to VCC, GND negative pole.
Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for Arduino AD pins..
【Package Included】2 x ACS712 Hall Effect Current Sensor Module + 2 x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.

Check Stock

DollaTek 5Pcs SW-420 NC Type Vibration Sensor Module Vibration Switch

Shipping list: 1 channel 24V vibration sensor plus relay module with 1 meter long shock sensor.
6-24V wide voltage power supply stable version With 1 meter long vibration sensor module, this module has no vibration delay function..

Check Stock

UMLIFE 3pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 3pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino Raspberry Pi

❃❃ Package Included：3 x ACS712 Hall Effect Current Sensor Module + 3x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
❃❃A wide range of applications:The current sensor ACS712 provides economical and accurate solutions for ac or dc sensing in industrial, commercial and communication systems. Typical applications include motor control, load detection and management, switching power supply and overcurrent fault protection..
❃❃ACS712 Hall Effect Current Sensor Module：Chip: ACS712ELC-30A.
Pin 5V power supply, on-board power indicator.
❃❃Voltage Sensor Module：Voltage input range: DC0-25V.
input : Terminal cathode connected to VCC, GND negative pole.
Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for AD pins..
❃❃Perfect Combination：Using this product can measure both voltage and current, very suitable for DIY electronic design projects..

Check Stock

ACS712 Hall Effect Current Sensor Module 5A 20A 30A Range + Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
【Package Included】1pcs x 30A,1pcs x 20A, 1pcs x 5A ACS712 Current Sensor Module, and 1pcs x Voltage Sensor Module DC0-25V Voltage Tester Terminal....
【Current Sensor Module】Chip: ACS712ELC-05A，Measuring range: ±5 amps, corresponding Analog output:185mV/A.--- ACS712ELC-20A，Measuring range:....
【Voltage Sensor Module】Voltage input range: DC0-25V.
【Pls Note】: ACS712 is based on the principle of Hall detection, please avoid the influence of magnetic field when using it!.

Check Stock

ICC/Intervox MEU-65PD-02-704, Microphone; 100 to 12000 Hz; 2 V; 0.5 mA (Max.); 6 mm x 5.2 mm; -70 dB

The sound sensor is suitable for assembly, and installed on various small equipment like microphone and robot.
Microphone sound sensor module possess small size, more stable performance and simpler installation.
Sound sensor module have small volume and low output noise, the fixed gain is 20dB, support 3.3v and 5v.
Low power consumption of sensor is easy to control, more stable and more efficient.
This module uses professional microphone amplifier IC, which possess high sensitivity.

Check Stock

ACEIRMC HC-SR04 Ultrasonic Sensor Distance Module for Nano Robot XBee ZigBee by ElecRight（5pcs

HC-SR04 Ultrasonic Sensor Distance Module: using IO trigger for at least 10us high level signal.
This module has stable performance and accurate measurement distance..
Detection distance: 0.78~196 in/ (2cm~500cm).
This module is fully Compatible with GH-311 anti-theft module..
HC-SR04 Ultrasonic Sensor Distance Module for Nano Robot XBee ZigBee by ElecRight.

Check Stock

waveshare for Raspberry Pi Pico Evaluation Kit B Include Pi Pico Board with Pre-Soldered Header,1.14inch RGB Color LCD, 10DOF IMU Sensor Module,Dual GPIO Expander,Breadboard

Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.

Check Stock

KEYESTUDIO Starter Kit V2 for Arduino with RJ11 Connector, Great STEM Education Kit for Students, Teachers and Hardware Enthusiast

Whenever you and your family go for vacations, you may used to get worried about your plants because they need water on regular basis. We develop this Automatic Plant Watering System to solve this problem as plants need water according to the moisture level of soil..
The kit includes a plus controller, DHT22 temperature and humidity sensor, I2C LCD, push button modules, power amplifier module, DS3231 clock module, non-contact level liquid sensor, motor driver module, capacitive soil humidity sensor, and pump..
More than 13 well-selected electronic modules and 17 step by step creative tutorials. Full example code is provided and explained and even includes useful software tool..
Multi-purpose: timing watering mode, and the sensor detection mode that when the soil is dry, Arduino will command the water pump to run(up to 4 plants at once)..
Our system measures the soil moisture and waters automatically according to it. A audio power amplifier module tells us when the bucket is empty. I2C LCD displays the temperature and humidity..

Check Stock

Ambient Weather WS-100-F007PF Smart Home Weather Station WiFi Module w/ Pool & Spa Sensor

Includes WiFi module and (1) F00PF pool /spa sensor.
Easily connects to routers and smart devices using WAP, up to 80 feet open air/line of sight.
NIST time synchronization from Internet with Auto DST, and optional calibration of all measured parameters.
Module powered by 6V, 500mA adapter (included).
Sensor has ssolar panel with 4 x AAA battery back-up (not included).

Check Stock

GAOHOU 2 PCS DS18B20 Waterproof Digital Temperature Sensor with Adapter Module for Arduino

The kit contains a waterproof digital temperature sensor DS18B20 and a DS18B20 adapter module..
It can measure the temperature directly in the water. Compatible with Arduino UNO R3 / Mega2560..
With pull-up resistor on board, the adapter module can be connected directly to most microcontrollers and it is widely used in temperature monitoring for fish tanks, equipment, machinery, greenhouses..
You can plug the sensor onto the adapter module directory with screwing..
Package Includes: 2X DS18B20 temperature sensor + 2 X adapter modules..

Check Stock