Top Current Tranformer Reviews

OWON Current Clamp Meter Multimeter CP-05+ Clamp Current Probe 200KHz 400A for Oscilloscope 4A 40A 200A 200-400A Test Range with BNC Connector

¡¾High Performance¡¿The current clamp can take accurate current readings .The current clamps are the ideal tools to extend the current ranges of Oscilloscope tools.Support Auto zero at power on, relative zero correction function.It has Band wide up to 200KHz,support low battery indication .Adopt of amorphous alloy core, with high performance, low loss ..
¡¾BNC connector¡¿The current clamp Multimeter features a BNC connector and can be plugged directly use. After connected well, switch the current clamp on (power LED should light) and then clamp the jaws around the current carrying conductor as shown. Typical Uses The AC/DC Current Probe simply offers the best value for money without compromising resolution..
¡¾Multiple Test Ranges¡¿The OWON CP-05+ current clamp is ideal for use with automotive oscilloscopes for measuring currents between 1 mA and 400 A. Various current test range, 4A, 40A, 200A, 200-400A test range are available.Low noise level, and high detection accuracy..
¡¾Easy to Use¡¿The current clamp has range selection settings, set by a slider switch on the handle of the probe. In use there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No ele....

Check Stock

HotSpot/Caldera Spas Replacement Spa Pillow - 76113

Replacement for: Hot Spot Relay 2010-Current, Hot Spot Rhythm 2010-Current, Hot Spot Tempo 2010-Current, Caldera Palatino 2010-Current, Caldera Marino 2010-Current, Caldera Vanto 2011-Current, Caldera Aventine 2010-Current and Caldera Tarino 2013-Current..
Replace worn out Hot Springs Hot Tub pillows with our Watkins Replacement Pillow! Your spa will have a fresh new look and restored comfort with a new spa neck pillow..
Hot Spring Spa Supplies carries spa fragrances, air & water valves, control systems, filter accessories, lights, cleaners, pumps, thermostats, and more for virtually every hot spring model..

Check Stock

Watkins item 71825 Filter Cartridge OEM for Hot Spring Hot Spot Solana and Caldera spas

71825 Hot Spring Replacement Filter is for the following models:.

Check Stock

Burley Design One-Wheel Stroller Kit, One Size, Black (960047)

Stroller wheel stays attached and folds up out of the way when cycling.
Tool-free adjustment makes switching from bike to stroll mode simple.
Burley easy-glide tow bar retracts closer to the trailer for easy maneuverability.
Compatible with: 2007-Current Honey bee, 2007-Current Encore, 2019-current Encore x, 2007-2018 solo, 2019-current d 'lite single, 2004-current d 'lite, 2019-current d 'lite x, 2007-2018 Cub, 2019-current Cub x, and 2008-current tail wagon.
Includes stroller wheel attachment and wrist tether.

Check Stock

RuiLing 1-Pack Thermal Switch Circuit Breaker Overload Protector 20A Mini Size Push Reset Button Switch

Test standard(25 degrees Celsius): 100% rated current: No trip off 150% rated current: trip off in 1 hour 200% rated current: 5~25 seconds trip off 300% rated current: 1.6~4.8 seconds trip off.
Life test: 125VAC x 150% rated current, 500 cycles.
Overload current: 10 times of rated current.

Check Stock

JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer

This ac current sensor used for measuring alternating current, particularly used for whole building consumption or generation..
This split core transformer is particularly suitable for DIY use and it works well with arduino and raspberry pi..
Use this split core current sensor to build your own energy monitor, reducing your power usage, or use it build an over-current protection device for....
Two Form of Output: current output or voltage output (burden resistor needed to add).
Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement and over-current protection.

Check Stock

DAOKI 5 pcs 5A Current Transformer ZMCT103C AC Sensor Single Phase Current Transformer Module Current Sensor AC Active Output Onboard Precision with Dupont Line for Arduino

【Features】：5A range single-phase AC mutual inductance module The inductance module is equipped with ZMCT103C series high-precision current transformers and high-precision sampling resistors to facilitate the collection of AC current within 5A.
【Convenience】：Sampling resistance of AC current transformer onload sampling resistance to facilitate the signal collection of AC current..
【Analog current output】：the module can measure the AC current within 5A, and corredsponding output is 5A/5mA.
【Small size】：Current transformer of AC current mutual module with precise miniature current transformer.
【Original】：Our electronic components are 100% original manufacturing, please rest assured to buy our products.

Check Stock

INA219 High Side DC Current Sensor Breakout - 26V ±3.2A Max

【Mini Split Base Current Transformer】It's the smallest one compared to the similar products (output 100MA).Current Transformer, 100A 100mA AC Current Sensor, Split Core Amp Transformer Sensing Relay, Mini Clip-on Easy to Install CT Without Power Off. current sensor structure sensor.
【Professional Use】Current transducer used for energy meter in special.
AC 220v, 380v power supply can both be applied.plit Core Current Transformer,AC Current Sensor,Output Class Analog Sensor,Working Principle Magnetic Sensor, Useful for Measuring Whole Building Electricity Consumption.current sensing relay isolation.
【Good Mechanical Properties】Fully enclosed, good mechanical properties and environmental resistance, strong voltage isolation capability, safety and reliability..
【Snap Joint Structure】The diameter of inner hole is 16mm, the accuracy is 0.5 grade, Using snap joint structure, it can be fixed to the cable directly through nylon ties..
【Easy to use】When you fix the energy meter, you don't need to cut off the power if you use this product. Split Core Current Transformer Coil Sensor for 100A Amp Energy Meter.ac transformer amp meter amp tester.

Check Stock

Adjustable Current LED Driver, DC 3.3V 3.7V 5V LED Driver 30-1500mA Constant Current Adjustable Module for LED 18650 Li-ion

This product is a current regulation integrated circuit operating from an input voltage of 2.8V to 6V, the constant output current can be set up to 1.5A with an external resistor..
It consists of high precision reference voltage, amplifier, current mirror, etc. The on-chip power transistor and current sense block greatly reduce the external component count, which makes this product ideal for LED driver..
When the CE pin is high, the input voltage is greater than 2.8V, and is larger than the LED forward voltage plus the required voltage drop, it functions normally to deliver constant current from the LED pin..
Adopts the temperature regulation instead of temperature protection function, the temperature regulation can make the LED being turned on continuously in case of high ambient temperature or high voltage drop. When the junction temperature reaches about 1.
With e chip enable function, which can shutdown the whole chip to limit the current consumption within 1uA. Adopts the over current protection block. When LED current approaches 1.9A(Typical), the over current protection block begins to function to prevent the LED current from increasing further..

Check Stock

Current Transducer, SZT15-CH-420E Current Transducer Transmitter Transformer Sensor AC Current Converter 0-50A,Stable Performance

【DC Current Output Signal】 - The SZT15-CH-420E AC current transducer provides real-time isolated measurement of AC current in the grid or circuit and converts it to a 0-5V / 0-10V or 4-20mA DC current output signal ..
【Withstand Voltage】 - Through-heart structure design, insulation withstand voltage up to 2000V AC. The measured current AC: 0-10A / 20A / 50A can be selected..
【Usage】 - Magnetic hysteresis less than 1%, can be used in strong magnetic field conditions. The current transducer is used for AC current monitoring, detection, current overload protection, and is also used as an electronic switch for automatic control systems..
【High Performance】 - The outer casing is made of self-extinguishing material, it has the characteristics of strong overload ability, high precision, high isolation, high security, low power consumption and strong anti-interference ability..
【Easy To Installation】 - There is no need to connect the dc series into the circuit during measurement, safe isolation of input and output. It is suitable for various applications requiring current and voltage conversion..

Check Stock

MakerHawk Electronic Load Tester - USB Load Tester 150W 200V 20A Resistor Adjustable Constant Current Battery Capacity Tester Module Intelligent Dischar

Prevent burning warning: when the input voltage battery and large power test, access must be beforeusing two current adjustment knob counterclockwise to the minimum to zero, then the access, accordingto the priority according to current power to slowly adjust current knob, must not instantly transferred infull, so there are excessive instantaneous power load discharge tube burnt huge risk! Please use thespecial attention to this point, thank you!.
Two power supply methods: 1. DC6-12V DC5.0 power supply.
2. DC6-12V Micro USB power supply.The body discharge power cannot exceed 150W, otherwise there is a risk of burnout..
Voltage measurement range: 0.00V ~ 200V, Current measurement range: 0.00A ~ 20A..
How to operate: Set the capacity, power, time using the Keystrokes method Reset:1. Reset button Long all data (mAh, Klitschko, 00: 00: 00).
2. Fast button twice capacity reset (mAh).
4. Fast button Four time reset (00:00:00).
5. Fast button five settings auto standby, Discharge count down regularly.
6. No load output No load, fast seven key, And current zero zero current, Environmental temperature Accurate calibration..
150W power refers to: In accordance with the power calculation formula P = UI (power = voltage x curre....

Check Stock

MakerHawk Electronic Load Tester USB Load Tester 150W 200V 20A Resistor Adjustable Constant Current Battery Capacity Tester Module Intelligent Discharge Resistance Power Tester

Prevent burning warning: when the input voltage battery and large power test, access must be beforeusing two current adjustment knob counterclockwise to the minimum to zero, then the access, accordingto the priority according to current power to slowly adjust current knob, must not instantly transferred infull, so there are excessive instantaneous power load discharge tube burnt huge risk! Please use thespecial attention to this point, thank you!.
Two power supply methods: 1. DC6-12V DC5.0 power supply.
2. DC6-12V Micro USB power supply.The body discharge power cannot exceed 150W, otherwise there is a risk of burnout..
Voltage measurement range: 0.00V ~ 200V, Current measurement range: 0.00A ~ 20A..
How to operate: Set the capacity, power, time using the Keystrokes method Reset:1. Reset button Long all data (mAh, Klitschko, 00: 00: 00).
2. Fast button twice capacity reset (mAh).
4. Fast button Four time reset (00:00:00).
5. Fast button five settings auto standby, Discharge count down regularly.
6. No load output No load, fast seven key, And current zero zero current, Environmental temperature Accurate calibration..
150W power refers to: In accordance with the power calculation formula P = UI (power = voltage x curre....

Check Stock

Digilent Pmod ISNS20: 20A Current Sensor

【FUNCTION】Adjustable DC current induction switch is a switch output detection, monitoring and protection product developed by using advanced non-sourced power supply (only for alternating current) technology.
【IDEAL CHOICE】Compared with the traditional transformer and thermal protector, the current induction switch has the advantages of high accuracy, stable performance and long service life, it is an ideal choice for automatic industrial control equipment and power monitoring.
【APPLICATION】Widely used in substations, variable frequency speed regulation devices, frequency converter devices, electrolytic plating, electric locomotives, street lamp monitoring, coal mines and other automation industries that require current monitoring.
【PRINCIPLE】The current induction switch uses the principle of electromagnetic mutual inductance of current for safety, introduction, and convenience to monitor or detect the current of electrical equipment.
【TWO TYPES】The switch type is normally open and normally closed, you can choose the appropriate product according to your needs, the startup time is less than 0.1 seconds. The shell material is fireproof ABS, which is safer to use.

Check Stock