Top Connecting Rod Cap Reviews

2 Pcs Piston Ring Oil-Less AB-9040019 For Husky Bostitch Air Compressor CAP2000P CAP2040P CAP1512 CAP60PB CAP60P

Fits Models: H27508UWK / A600006. Does NOT fit the "WL" or other series units. Part Numbers: AB-9040019, AB9040019.
40mm ID. This is for the 50mm Cylinder Bore..
This part is installed on top of the piston/connecting rod.Its purpose is to create a seal in the cylinder so that air can be pump into the compressor tank..
If this part wears your compressor will not pump the air properly.This is a wear part and it is advised to keep an extra one on hand..
This part is compatible with the following machines: Bostitch CAP2000P-OF Type 0 Air Compressor CAP2040P-OF Air Compressor CAP60P-OF Air Compressor CAP60PB-OF Air Compressor CAP1512-OF (Type 0) Air Compressor.

[SPECIFICATIONS] Cam fittings: diameter 15mm (0.59"), height 13mm (0.51"). Connecting rod bolts: total length 36mm (1.41"), thread length 9mm (0.35"), thread diameter 6mm (0.24"). Plastic nuts: diameter 10mm (0.39"), height 9mm (0.35").
[MATERIAL] Pre-assembled nuts are made of plastic, cam fittings are made from aluminum alloy, and connecting rod bolts are made from high quality zinc alloy with nickel plated on the surface, they have good corrosion resistance, rust resistance, high hardness and stable structure to ensure long service life..
[APPLICATION] The perfect partner for installing furniture, they can make the vertical connection between furniture panels. They can be applied to board wardrobes, shoe cabinets, drawers, cabinets, bed cabinets, etc., especially particle board and particle board..
[EASY TO USE] Super easy to install and remove, they save you a lot of time and energy. 1. Knock the plastic pre-insertion nut into a target position on the plate one. 2. Use a cross screwdriver to screw the connecting rod nut into the pre-assembled nut on the plate one. 3. Aligh the hole of plate two with the connecting rod bolt and place it on the plate one, then tighten the cam fitting clockwise to tighten the connecting rod bolt..

Includes: Engine Block with Piston and rings, Piston Pin, Connecting Rod, Crankshaft, Crank Seals, Crankcase Cover, Camshaft Balancer, Shaft, Low Oil Sensor, Governor, Oil Dipstick/Fill Cap.

17,000 BTU heat input heats up to 570 sq. ft..
Designed for use with liquid propane gas.
Sealed burn system is perfect for bedrooms and living spaces.
Matchless Piezo lighting for quick starts.
No complicated venting to purchase or install, complete kit is included (includes heat shield, vent pipe, air intake pipe, flashing, cap and connecting rod).
Approved for use in mobile or modular homes.

Heats up to 825 sq. ft. with up to 25,000 BTU heat input.
Designed for use with liquid propane gas.
Sealed burn system is perfect for bedrooms and living spaces.
Matchless Piezo lighting for quick starts.
No complicated venting to purchase or install, complete kit is included (includes heat shield, vent pipe, air intake pipe, flashing, cap and connecting rod).
Approved for use in mobile or modular homes.

Engine connecting rod and piston holder measures 24 inch long x 12 inch wide x 9-1/2 inch tall.
This combination rod and piston holder safely supports piston and connecting rod assemblies during engine teardowns or assembly.
Slots are 4-3/4 inch long x 1-1/2 inch wide to accommodate most piston/rod combinations.
Assembly is required and can also be disassembled if desired after use for easy storage.

17,000 BTU heat input heats up to 570 sq. ft..
Sealed burn system is perfect for bedrooms and living spaces.
Matchless Piezo lighting for quick starts.
No complicated venting to purchase or install, complete kit is included (includes heat shield, vent pipe, air intake pipe, flashing, cap and connecting rod).
Approved for use in mobile or modular homes.

Heats up to 825 sq. ft. with up to 25,000 BTU heat input.
Sealed burn system is perfect for bedrooms and living spaces.
Matchless Piezo lighting for quick starts.
No complicated venting to purchase or install, complete kit is included (includes heat shield, vent pipe, air intake pipe, flashing, cap and connecting rod).
Approved for use in mobile or modular homes.

11,000 BTU heat input heats up to 375 sq. ft..
Sealed burn system is perfect for bedrooms and living spaces.
Matchless Piezo lighting for quick starts.
No complicated venting to purchase or install, complete kit is included (includes heat shield, vent pipe, air intake pipe, flashing, cap and connecting rod).
Approved for use in mobile or modular homes.

32Pcs Rotary tool mini cutting discs sets include 6pcs 22/ 25/ 32/ 35/ 44/ 50/mm woodworking thin cutting wheel +10pcs black mesh 32mm resin cutting wheel +10pcs 22mm emery cutting wheel +30pcs 22mm red polishing wheel + 1pc 1/8" connecting rod + 1pc 1/4 "connecting rod + 4pc 3mm connecting rod.
Mini saw blades made of high-hardness steel, hard texture, wear-resistant and heat-resistant, surface-plated emery, fine and uniform particles, rotary tool cutting disc can be used to polish or cut the surface of objects, high cutting efficiency and durability.003cbr/003e.
Rotary cut-off wheel kit has 6 assorted cutting discs set for different needs, HSS mini saw blades for wood and plastic / Diamond cutting wheels for stone / Resin cutting wheels for metal..
The cut-off wheels set + is suitable for all kinds of metal, wood, drywall, plastic, stone, ceramic, glass, hard alloy, the treasure jade stone processing and more / Ideal for cutting, grooving and trimming.003cbr/003e.
Compatibility: Shank cutting disc mandrels fit for most power die grinders or rotary tools & air tools.003cbr/003e.

APPLICATION: For Cement Brick Concrete Stone Wall..
WHAT YOU WILL GET:1x 110mm / 4.33 " drill bit,1x 220mm connecting rod,1x Center positioning drill bit ,1x positioning drill screw.

OEM replacement connecting rod, ideal for the motorbike.
High quality forged steel material, safe and durable.
Includes connecting rod, crank pin, crank pin bearing,thrust washers.
Quality Assurance! If you are not satisfied with our products, we accept all of the return, replacement or refund requests.

APPLICATION: For Cement Brick Concrete Stone Wall..
WHAT YOU WILL GET:1x 160mm / 6.3 " drill bit,1x 220mm connecting rod,1x Center positioning drill bit ,1x positioning drill screw.