Top Conduit Chase Nipple With Locknut Reviews

1-in Liquid-Tight Connector

  • Superior liquid tight seal and pull out strength.
  • No threading of the conduit or tubing required.
  • Smooth interior surfaces for easier wire installation.
  • Furnished with steel locknut and seal gasket.
Check Stock

Klein Tools D333-8 Conduit Locknut and Reaming Pliers

  • Pliers tighten 1/2-Inch (13 mm) and 3/4-Inch (19 mm) EMT or 1/2-Inch (13 mm) rigid locknuts.
  • Reams and smoothes both inside and outside of conduit.
  • Knurled jaws at nose tip pull wire or fish tape and machined nose fits snugly into locknut wings.
  • Forged in the USA with custom, US-made tool steel for maximum durability.
Check Stock

Lamson E943E-CAR Carlon Male Adapter

  • Material: Nylon material, resist sea water, gasoline, alcohol ,grease and so on..
  • Performance: Flammability classification 94V-2.
  • Installation: Easy to install, no diassembly required, just simply push the conduit or tubing onto the ferrule, tightening the domed sealing nut..
  • Application: Suitable for indoor/outdoor usage.
Check Stock

1 Inch 90 Degree Nonmetallic Liquid Tight Electrical Conduit Conector Fitting, 4 Pack, UL Listed

  • Material: Nylon material, resist sea water, gasoline, alcohol ,grease and so on..
  • Performance: Flammability classification 94V-2.
  • Installation: Easy to install, no diassembly required, just simply push the conduit or tubing onto the ferrule, tightening the domed sealing nut..
  • Application: Suitable for indoor/outdoor usage.
Check Stock

OTC 4542 Stinger Wheel Bearing Locknut Socket Set - 7 Piece

  • 7-Piece wheel bearing locknut socket set.
  • For use with 1/ 2 inch ratchet or breaker bar.
  • Set contains 55 mm hex locknut socket 2-3/8 inch hex locknut socket 2-1/ 2 inch hex locknut socket 2-1/ 2 inch rounded hex locknut socket 2-3/4 inch rounded hex locknut socket 2-9/16 inch rounded hex locknut socket and 2-3/8 inch rounded hex locknut socket works.
Check Stock

Mueller Industries 109-814 Float Valves, 0.75 Inch

  • Dual inlet thread for connecting pipe and locknut.
  • Machined flange for support against tank wall.
  • Dual inlet thread for connecting pipe and locknut, high tensile serrated arms, locknut included with male inlet valves.
Check Stock

OTC 1909 3-1/4" 8-Point Octagon Locknut Wrench

  • 3-1/4 inch 8-point octagon locknut wrench.
  • High strength steel resists rounding out.
  • For use with 3/4 inch square-drive manual tools only.
  • Measure from flat to flat to determine size of locknut.
Check Stock

KiWAV Tappet Valve Adjustment Wrench Tool Set Timing Chrome Vanadium Steel

  • The hand tool allows micro adjustment without disturbing the locknut which can be tightened when the correct clearance is achieved..
  • Use a 12mm wrench to hold the locknut socket while using square type driver to loosen or tighten the valve adjustment screw..
  • 8, 9mm locknut sockets and 3mm square type driver included..
  • Fits most motorcycles and ATVs with screw-type tappet adjustments..
Check Stock

NOVINO 14-1/2Dia X 19Pitch Boat Outboard Propeller for Mercruiser Alpha One Prop/Mercury Engine 135 150 175 200 220 225 250 300HP,3-Blade Aluminum 14.5dia x 19 Pitch Propeller,Replace OEM#48-832830A45

  • ... pitch Mercury/Mercruiser propeller,lower fuel consumption and great speed acceleration or rmps,,reduce the wear and tear on engine.
  • Easy Install: The propeller with hub kit Includes Flo-Torque hub kit (hub, splined hub, thrust washer, prop nut and keeper),Just remove prop locknut&locknut retainer& forward thrust washer.Then Install forward thrust washer---Insert drive sleeve into prop---Slide prop on prop shaft---Insert drive sleeve adapter--Slide locknut retainer---Install prop locknut---Insert sth to prevent spinning--Tighten prop locknut.
  • Fitment:perfect propeller replacement for 14.5x19pitch Mercury Engines 135 150 175 200 220 225 250 300HP&Mercruiser Alpha One Bravo One,detail information pls see below.
Check Stock

Manufacturer Morris Products Codes 17454 Post Base Channel 4 Hole Square – for 1-5/8” Strut – Side Orientation, Galvanized Steel – 6” x 6” Base – Pack of 3

  • Material:Conduit hangers are made of zinc-plated iron,durable to use..
  • Conduit hanger ensure that the rigid conduit and EMT conduit are securely secured to the mounting surface..
  • High-quality and durable conduit hangers with bolt..
  • Used to secure and suspend EMT, rigid conduits from overhead supports..
Check Stock

Sigma Electric ProConnex C-560 Snap Lock AC/MC Connector 3/8-Inch, 25-Pack

  • Terminates AC or MC to a 1/2" knockout without a locknut.
  • For aluminum or steel 14/2 - 10/3 AC or MC.
  • No locknut assembly for faster installation.
Check Stock

Valterra RF850 1/4\ MPT x 3/8\ Barb Adapter

  • Right Angle Nylon Cable Glands NPT Thread - These Right Angle Cable Glands are corrosion resistant..
  • Seal & clamp system allows the cord connector to tighten in a circular sequence on the sealing ring to give outstanding strain relief without twisting or damaging the cable.
  • Simply push the cable through the liquid tight Nylon strain relief & tighten locknut for quick installation.
  • Threads into your panel for clearance, locknut included.
Check Stock

Gardner Bender LNW-3PC LNW locknut wrench, Assorted

  • Locknut wrench solves the problem of tight spaces and fits the majority of UL locknuts.
  • Etched markings allow for easy identification.
  • clearly marked tighten and loosen ends make usage a breeze.
  • each tool is a different color for easy size identification.
  • Thin design allows easy maneuvering in tight locations.
  • Hooked tip latches onto locknut and maximizes turning leverage.
  • 3-piece kit includes the 1/2 in. , 3/4 in. and 1 in. sizes.
Check Stock