Top Computer Pcb Board Reviews

uxcell 0.5mm Pitch 20 Pins to 20 Pins Extension Connector Aapter for FFC FPC Cable Extend Zip HDD

  • [Specification]: 20 Pin to 20 Pin 0.5mm Pitch for 20 Pin FFC Cable.
  • [Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
  • [Type]:This is 0.5mm pitch FPC connector extend adapter for make longer install..
  • [Package]:1 x Pin to Pin 0.5mm Pitch FPC Connector Extend Adapter.
  • [Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..
Check Stock

Engineering Notebook: Graph Paper Notebook Quadrille 4 X 4 Quad Ruled Book: 100 Pages (.25″ Lab Grid Format), 8″ x 10″ (Notebooks for Students)

  • Electrical Engineer Keychain, Circuit Board Keychain, Electronic Engineering, Computer Engineering, Gift for PCB Printed Circuit Board Design Engineer, Electrical Engineer, Engineer Teacher, Engineer Graduation Gift.
  • Engineer Charm, Circuit Board Charm, Computer Charm, Electric Plug Vector Charm.
  • Diameter of Key Ring : 1.38 Inches (3.5 cm).
  • Length of Keychain : 2.95 Inches (7.5 cm).
  • Free velvet gift bag to pack and ship our keychain.
Check Stock

ACASIS USB C 3.2 SSD Enclosure for Apple Flash SSDs 12+16 PIN MacBook Pro,MacBook Air, Mac Pro, iMac from 2013 to 2017 Portable Storage Enclosure Compatible with M.2 Nvme SSD with Adapter

  • [More Compatibility] This USB C 3.2 SSD enclosure support for apple Mac SSD with 12+16PIN which was original factory-installed. NOT SUPPORT Toshiba 12+16PIN SSD and all SATA SSD. NOT compatible with Third-party SSDs, including OWC SSDs. Support M.2 Nvme SSD after installing the enclosed interface adapter..
  • [Faster Data Transmission] 10Gbps transmission speed with USB 3.2 Gen2 interface. Save and transfer data in a seconds. It can also reach 20Gbps transmission speed with USB 3.2 Gen2x2 if the computer supports..
  • [Friendly Design] Aluminum alloy case for quicker heat dissipation. ACASIS USB C 3.2 SSD enclosure is sturdy and portable..
  • [System Requirements] ACASIS USB C 3.2 SSD enclosure supports Windows7/8/10/11,Mac OS 10.0,Linux 2.6 or later.Supports for 2013-2017 MacBook Air, 2013-2015 MacBook Pro Retina, 2013-2014 iMac, 2013 Mac Pro.
  • [Easy Installation] Just take out the PCB board from the enclosure,then fully insert SSD to card slot of the PCB board, put PCB back into the enclosure,tighten the screws.Plug and play, support hot plug.On Windows OS, hard disk will not available on "This PC"/ "My computer.
Check Stock

Engineer Keychain Circuit Board Keychain Electrical Engineer Gift Electronic Design Engineering Computer Engineering Computer Laptop Charms Engineer Teacher Gift Engineer Student Graduation Gift

  • Electrical Engineer Keychain, Circuit Board Keychain, Electronic Engineering, Computer Engineering, Gift for PCB Printed Circuit Board Design....
  • Engineer Charm, Circuit Board Charm, Computer Charm, Electric Plug Vector Charm.
  • Diameter of Key Ring : 1.38 Inches (3.5 cm).
  • Length of Keychain : 2.95 Inches (7.5 cm).
  • Free velvet gift bag to pack and ship our keychain.
Check Stock

CPU Chip Gift - Electrical Engineers Computer Circuit Board T-Shirt

  • Men and women are pleased with this gift idea for Christmas or birthday when developing electronic circuit boards and their CPU. A gift for children if they want to be like electronics and program on the computer..
  • The board in a computer developed by the engineer with a CPU and a motherboard. Computer scientists and electrical engineers and electronics engineers are designing the PCB engineers..
  • Lightweight, Classic fit, Double-needle sleeve and bottom hem.
Check Stock

Zorveiio 50 Pcs PCB Board Mounting Feet with Screws, PCB Spacer Kit PCB Feet Plastic PCB Standoffs for Arcade Gaming Board Console Motherboard

  • 【Premium Material】Our pcb board mounting feet are made of high quality insulating plastics, which is sturdy, strong enough and durable in use. Such reliable plastic spacer can stay firmly on PCB Board, good insulation with long service life..
  • 【Pacakge & Suitable Size】 You will receive 50pcs L type pcb feet and 100pcs mounting screws (Each foot comes with 2 pieces screws). Each pcb standoff measures approx. 0.8" x 0.8"/21.2mm x 20.3mm, can secure the board tightly. Sufficient enough for you to satisfy using and replacing daily needs..
  • 【Widely Usage】Our plastic pcb feet are suitable for PCB packaging and stacking applications. Specially for fixing gaming boards, game console motherboard, video board, arcade gaming board ect and work well. Serve as ideal replacement hardware parts and offer you much convenience in your daily life..
  • 【Easy to install】 These pcb spacer kit is easy to install and use, you just need to tighten mounting screws in a breeze, will not need a lot of labor. It can secure the circuit board to other surfaces effortlessly..
  • 【100% Risk-Free Shopping】 Zorveiio's products are backed by incredible customer service to make sure your satisfaction is guaranteed. If you have any other questions about it, please do not hesitat....
Check Stock

Dashtop 40 pcs L Type PCB Mounting feet / legs with Screw Fit for Arcade Games Jamma Game Video Games Windows System Raspberry Pi Board

  • MATERIAL: PCB standoffs are made of insulating plastics, strong and durable in use..
  • SIZE: The size of insulated PCB spacer – 20 x 20 x 9mm / 0.8 x 0.8 x 0.35in (LxWxH). Supporting Height: 20mm / 0.8 inch.
  • TWO SCREWS HOLES: Each L type PCB board mounting feet comes with 2 screws to secure the circuit board to other surfaces easily.
  • APPLICATIONS: Circuit Board Standoffs suit for game console motherboard, video board, and so on, serve as ideal replacement parts and provide you much....
  • Apply for: our L type PCB board mounting feet with screws fit well with arcade gaming board, video board and so on, serve as ideal replacement parts....
Check Stock

Dorhea ESP8266 ESP-12 NodeMcu D1 Module WeMos Lua 4M Bytes WLAN WiFi Internet Development Board + Relay Shield + 2.54mm 40Pin Single Row Male Pin Header - 3Set

  • The esp8266 module is 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB connection.
  • WiFi internet development board 5V 1A switching power supply (switching power supply）onboard..
  • 5V relay shield is a digital switch to control much higher voltages and currents than esp8266 mini microcontroller, controlled by the D1 , the relay will switch to allow current to flow or turn off, depending on wiring..
  • 40 pin 0.1inch (2.54mm) male pin header connector PCB board pin strip electronic component, they are easy to be cut to any length if needed, you can cut or score with some electronic tool..
  • The pin header is an ideal connector for the PCB board and intergrated circuit, used widely in the computer and breadboard, compatible with raspberry pi or other electronic project..
Check Stock

Yellow Sanwa LB35 Balltop for JLF Joysticks

  • Original Sanwa Denshi TP-MA Replacement PCB with Microswitches.
  • Replacement microswitch PCB for Sanwa JLF series Joysticks.
  • Often the PCB is the first to go out on a Sanwa JLF in a few years. Restore it to brand new by getting the Sawa TP-MA PCB assembly. This replaces the entire set of microswitches and PCB, and housed in very easy to install module..
  • Installation: Remove the Sanwa JLF lever restricted Remove the TP-MA board that comes from the Sanwa JLF lever Place the new board pointing in the same direction as the previous one. Finally place the restrict again.
  • Package include One pcs Original Sanwa TP-MA PCB with Microswitch.
Check Stock

Pieces 4 Pin LED Light Strip Connectors Set Including Screw Fixing Clips, 4 Pin LED Connectors, Cuttable T, L and X Shape PCB Board for SMD 5050 RGB LED Strip Lights Gapless Solderless Connector

  • ... stand up to 4A current and 0 - 24V (5V, 12V, 24V) voltage, the heat resistance level is -20℃ - 100℃, so they are suitable for most non-waterproof 4 pin SMD 5050 RGB lights in 0.39 inch/ 10 mm width.
  • Note: you should pay attention to use them correctly for ensuring safety and extending service life.
  • Cuttable PCB board: the PCB board is cuttable, so you can use a cutting tool to cut T-shaped, L-shaped and X-shaped PCB board into any shape you want to facilitate the connection of various forms of light strips.
  • Just use your imagination to DIY a special light strip.
  • Please cut the LED strip according to the cuttable mark when you want to change the shape of PCB board.
  • Simple to install: the LED strip connector clip can be easily opened and closed, you can quickly slide RGB strip into the connector clip without any tool, please make sure connector + - polarity in line with + of strip before you connect it.
  • Wide range of usages: the 5050 LED strip connectors are suitable for standard density strips or DIY LED lights, for corner connection, and able to decorate Christmas trees, parties, birthdays, weddings, parties and other scenes according to your own needs.
  • Sufficient quantity: the package comes with 40 pieces 4 pin LED connectors, 15 pieces L-shaped PC....
Check Stock

DNYSYSJ 1500W CNC Router Engraver Machine, 6040 3Axis USB Engraving Drilling Milling Carving Machine 3D Carving Desktop Machine DIY Artwork Woodworking

  • ★【It can work with various materials(metallic & non-metallic)】Such as: wood, pmma or other plastic, MDF board, native wood, PVC, Acrylic, wood, composite board plywood. and soft metal .like aluminum, copper and silver to engrave them into 3D/2D works etc. The machine can connect with computer as other external device such as printer, scanner. With the assist of the ROUTER 6040T, your design idea will be real-time display..
  • ★【Water cooled spindle motor】It can work longer time than air cooled motor.Water cooled spindle motor has higher stability and better concentricity than air cooled motor,water cooling spindle works more stable and durable.(tips：1. The spindle motor must connect with the VFD.)The mini router Frame is movable..
  • ★【It can used for engraving】Advertising signs, PCB, nameplates, badges, seals, bronzing plate, aluminum alloy, acrylic plates, ABS resin doublecolor plate, PVC foaming board, indentation plates, signs, construction models, instrument panels, wooden products, etc..
  • ★【Wide Range of Applications】This 6040 machine is suitable for industry, Technology Research, Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. Suitable for PCB, wood, Plexi glass, PVC, Crystal Acrylic, RESIN, Pla....
Check Stock

AmScope - Adjustable Circuit Board Holder and Clamping Kit PCB Holder Frame - Single Pack - 1 Piece

  • Adjustable printed circuit board holder (PCB) holds objects in place for soldering, repair or inspection functions.
  • Wide base with rubber feet creates a solid and safe work platform.
  • Spring-loaded clamp holds objects up to 7 ¾” wide (198 mm) securely in place.
Check Stock

Prototype Screw Terminal Block Shield Board Kit MEGA-2560 R31

  • FLEXIBLE USE---Without assembled, the prototype screw terminal block shield board allows you to try variety mount methods, so that you can use it flexibly.
  • COMPACT STRUCTURE---With compact structure, the prototype screw terminal block shield board is made up of screw terminal block, high quality PCB carrier, FR-4 glass fiber PCB.
  • RICH COMPONENTS---The prototype screw terminal block shield board includes prototype PCB, terminal blocks, and female header sockets, satisfying your working needs.
  • LONG SERVICE PERIOD---Made of high quality of material, and with delicate workmanship treatment, the prototype screw terminal block shield board has long serving life, practical and economic.
  • EXCELLENT AFTER SALE SERVICE---Except the premium product we provide, we also provide considerate after sale service. Please contact us for any problem about our product. It is our pleasure to service you.
Check Stock