Top Cobalt Steel Reviews

Drill America #44 Solid Carbide Drill Bit, DMOD Series

  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools.
  • performance is similar to uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to National Aerospace standard 907.
Check Stock

3/32-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 3/32-inch cutting diameter, 1-1/4-inch flute length, 2-1/4-inch overall length, 118 degree point, straight shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 3/32-inch cobalt drill bits with case.
Check Stock

1/4-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 1/4-inch cutting diameter, 2-3/4-inch flute length, 4-inch overall length, 135 degree split point, 3-flat shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 1/4-inch cobalt drill bits with case.
Check Stock

1/8-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 1/8-inch cutting diameter, 1-5/8-inch flute length, 2-3/4-inch overall length, 135 degree split point, straight shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 1/8-inch cobalt drill bits with case.
Check Stock

3/16-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 3/16-inch cutting diameter, 2-5/16-inch flute length, 3-1/2-inch overall length, 135 degree split point, 3-flat shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 3/16-inch cobalt drill bits with case.
Check Stock

5/16-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 6

  • JOBBER LENGTH: 5/16-inch cutting diameter, 3-3/16-inch flute length, 4-1/2-inch overall length, 135 degree split point, 3-flat shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 6 pieces of 5/16-inch cobalt drill bits with case.
Check Stock

TEMO M35 Cobalt Spiral Flute Type Step Drill, 9 Size from 1/4 Inch To 3/4 Inch, 3/8 Inch Shank

  • TEMO M35 Cobalt Spiral Flute Type Step Drill, 9 Size from 1/4 Inch (6.4 mm) To 3/4 Inch (19 mm), 3/8 Inch (9.5mm) Shank.
  • 9 hole sizes: 1/4″ (6.35mm), 5/16″ (7.94mm), 3/8″ (9.52mm), 7/16″ (11.11mm), 1/2″ (12.7mm), 9/16″ (14.29mm), 5/8″ (15.88mm), 11/16″ (17.46mm), 3/4″ (19.05mm), with 1/16″ (1.59mm) increments. 3/8 Inch Shank with 3 flats to eliminate slipping.
  • Double spiral flutes for more efficient swarf clearance.
  • 1/4 Inch hex Shank with quick release slot to eliminate slipping.
  • Self-starting for clean holes in thin materials.
  • M35 cobalt HSS to cut stainless steel. The step drill bit is made with M35 cobalt. It is ideal for variety of materials from stainless steel, metal, plastic, fiberglass to wood. They also help to enlarge existing holes. M35 HSSCo is a high speed steel alloy made up of 5% cobalt. M35 is similar to M2, but with 5% cobalt added..
  • The addition of cobalt increases heat resistance. It is widely used in metal manufacturing because of its ability to resist wear over conventional high speed steels, allowing for shorter cycle times in production environments due to higher cutting speeds or from the increase in time between tool changes. M35 is also less prone to chipping when used for interrupted cuts..
Check Stock

Drill America 1' Reduced Shank Cobalt Drill Bit with 1/2' Shank, DWDCO Series

  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools.
  • performance is similar to uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Manufactured to National Aerospace standard 907.
Check Stock

TEMO M35 Cobalt Spiral Flute Step Drill 12 Size From 3/16 Inch To 7/8 Inch 1/4 Inch Hex Shank

  • M35 cobalt step drill 1/4" (6.35mm) hex shank 12 hole 3/16" (4.76mm) to 7/8" (22.22mm).
  • 12 hole sizes: 3/16" (4.76mm), 1/4" (6.35mm), 5/16" (7.94mm), 3/8" (9.52mm), 7/16" (11.11mm), 1/2" (12.7mm), 9/16" (14.29mm), 5/8" (15.88mm), 11/16" (17.46mm) , 3/4" (19.05mm), 13/16" (4.76mm), 7/8" (22.22mm) with 1/16" (1.59mm) increments. The size marks are stamped next to each step to ease the use..
  • double spiral flutes for more efficient swarf clearance.
  • 1/4 Inch hex Shank with quick release slot to eliminate slipping.
  • Self-starting for clean holes in thin materials.
  • M35 cobalt HSS to cut stainless steel. The step drill bit is made with M35 cobalt. It is ideal for variety of materials from stainless steel, metal, plastic, fiberglass to wood. They also help to enlarge existing holes. M35 HSSCo is a high speed steel alloy made up of 5% cobalt. M35 is similar to M2, but with 5% cobalt added..
  • The addition of cobalt increases heat resistance. It is widely used in metal manufacturing because of its ability to resist wear over conventional high speed steels, allowing for shorter cycle times in production environments due to higher cutting speeds or from the increase in time between tool changes. M35 is also less prone to chipping when used for interrupted cuts..
Check Stock

M35 5% Cobalt Metric Drill Bits Set (1mm-10mm/19pcs), Straight Shank Jobber Drill Bits, Metal HSS Twist Drill Bits for Stainless Steel Hard Metal and Cast Iron

  • ✅【5% COBALT TWIST DRILL BITS SET】Made from M35 Cobalt Steel with Molybdenum and Cobalt added to form a hardened alloy, can measure up to 67 Rockwell hardness, cut faster, last longer, and last longer than normal HSS drill bits 12 times..
  • ✅【19PCS METRIC DIRLL BITS SET】The set includes 19pcs of M35 cobalt steel twist drill bits: 1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7 mm, 7.5mm, 8 mm, 8.5mm, 9 mm, 9.5mm, 10 mm. Organized in a sturdy plastic storage case for easy transport to your workplace..
  • ✅【TWIST DESIGN AND PERFORMANCE】Precise 135° SPLIT Point, Gold Oxide Surface and Round Straight Shank. Prevents walking and removes chips and particles faster. Precision fully ground to ensure smooth chip movement..
  • ✅【PROFESSIONAL AND WIDELY USED】M35 Cobalt High Speed Steel is more suitable for hardening materials. Ideal for cutting stainless steel, steel and cast iron as well as wood, aluminum alloys and other metals. Not suitable for glass or ceramic materials. Pay attention to speed, pressure and heat control when drilling..
  • ✅【SERVICE】If you have any problem with our metric drill bit set or are not satisfied with the product, please feel free to contact WildBossy..
Check Stock

KEO 53528 Cobalt Steel Single-End Countersink Set, Uncoated (Bright) Finish, 90 Degree Angle, 5/16\ - 5/8\ Head Diameter

  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications.
  • Straight shank, CNC precision cam ground, M35 cobalt steel material, chatter-free cutting action.
Check Stock

Drill America - DWDCO43P12 #43 Cobalt Drill Bit (Pack of 12), DWDCO Series

  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools.
  • performance is similar to uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Ideal for drilling in tough, high tensile strength materials.
Check Stock

Drill America DWDCO40P12 #40 Cobalt Drill Bit (Pack of 12), DWDCO Series

  • Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.
  • Gold oxide is a thinner oxide surface treatment than black oxide typically used to identify cobalt steel tools.
  • performance is similar to uncoated tools.
  • Round shanks allow use with a wide variety of toolholding systems.
  • When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
  • Ideal for drilling in tough, high tensile strength materials.
Check Stock