Top Cnc Interface Board Reviews

Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..

Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

Check Stock

MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board Controller Card for CNC Engraving Servo Motor Stepper Motor Servo motor

【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....

Check Stock

Straight Shank Tool Holder, 45-46HRC Hardness 1-7mm Clamping Range 40Cr and Carbon Steel CNC Milling Extension Rod for Lathe Device(C16-ER11A-150L)

Isolated IO port means that with input and output ports isolated from the system, the output port capacity can be up to 1A.
Direct output terminal interface on the back reduces the transfer board, the terminals on the back can be directly wired, clear and convenient, which saves costs.
Supports automatic operation including dry running and singlestep running, CNC lathe controller 's manual operation including motor CW /CCW, back to program 0, back to mechanical 0 and output control..
You can directly use the USB cable to power the system, which is convenient for the transmission of the boot screen and the program, learning and operation.
With 20 control commands, external manual supports control motor CW /CCW, start, pause, alarm, emergency stop, etc..

Check Stock

Milling Machine Linear Scale, 170mm High Accuracy Linear Encoder for Milling Lathe Machine

Supports automatic operation including dry running and single step operation, manual operation of the CNC lathe control including motor CW/CCW, back to program 0, back to mechanical 0 and output control..
The interface of the direct output terminals on the back reduces the transmission board. The terminals on the back can be directly wired, clear and convenient, which saves costs.
Isolated I/O port means that with input and output ports isolated from the system, the output port capacity can be up to 1A.
You can power the system directly using the USB cable. This is practical for the transfer of the start screen and the program as well as for learning and operation.
With 20 control commands, the external manual supports the control motor CW/CCW, start, pause, alarm, emergency stop etc. The parameters of the CNC lathe control include system parameters, system self-test, I/O settings, user and manufacturer password management etc. and it supports also editing, reading, deleting and saving programs..

Check Stock

CNC 3018 Pro Wood Router Kit 3 Axis USB DIY Mini Engraver Milling Engraving Machine Cutter Plastic Acrylic PCB PVC Carving GRBL Control 300x180x45mm

♞【Upgrade Version 3018 Pro】Mini CNC machine small size, light weight, USB interface, GRBL control systems, great cnc router machine for beginers.
The CNC3018 PRO machine is very easy to install,stable structure..
Type:USB Port mini desktop cnc router【Spindle】 775 spindle motor (12-36V) DC24V:10000r/min【Stepper Motor】Nema17 stepper motor,1.3A, phase resistance 2.1 ohms, torque 0.25N.m.
♞【Upgraded GRBL1.1 Control Board】Added the outer casing,emergency stop button port,tool setting (probe) port,X/Y/Z axis limit port and add the power button switch,and come with the fan port to force heat dissipation,with enhanced spindle drive,can support maximum 20000rpm spindle,and also can support 0.5W-20W module..
♞【Main application】Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material,also can work on soft metal like copper,brass,aluminum and other similar metal materials, but can not carve hard metal, jade or other very hard texture of the items..
♞【GRBL Software】Our parcel include a 4G USB flash drive,it include the installation instructions,user manual and GRBL software.
♞【System requirements】 Windows XP SP3,Win 7,Win 8,Win 10 (32/64 can be)....

Check Stock

3-Axis 32-bit ARM Based CNC Controller,GRBL 1.1F USB Port CNC Engraving Machine Control Board with Fan Cooling,Support 500W Spindle/NEMA23 Stepper Motor/Laser (A4988+Fan)

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

Check Stock

ANNOYTOOLS ARM 32-bit 3-Axis CNC Controller,GRBL 1.1F USB Port CNC Engraving Machine Control Board with Fan Cooling DRV8825 Standalone Driver,Support 500W Spindle/NEMA17/23 Stepper Motor/Laser Module

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

Check Stock

CNC 3018 Pro Max 3 Axis Desktop DIY Mini Wood Router Kit Engraver Woodworking PCB PVC Milling Engraving Carving Machine GRBL Control with ER11 Collet (3018 Pro Max)

♞【Upgrade Version CNC3018 Pro Max】Mini CNC machine small size, light weight, USB interface, GRBL control systems, great cnc router machine for beginers.
3018 PRO MAX machine is very easy to install,stable structure,our parcel also include english user manual..
Type:USB port Desktop cnc router【System requirements】Windows XP / Win 7 / Win 8 / Win 10 / Linux.
Supporting files:G-code (.nc/.txt/.tape/.gcode).
♞【Upgraded GRBL1.1 Control Board】Added the outer casing,emergency stop button port,tool setting (probe) port,X/Y/Z axis limit port and add the power button switch,and come with the fan port to force heat dissipation,with enhanced spindle drive,can support maximum 20000rpm spindle,and also can support 0.5W-20W module.【Spindle&Stepper Motor】775 spindle motor (12-36V) 24V:10000r / min.
Collet: ER11 3.175mm (Can be equipped with 0-7mm).
♞【Main application】Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material.soft metal like copper and aluminum and ot....

Check Stock

MT3 BT30 ER25 8000r/m Engraving Spindle Unit Power Head Induction Motor Mechanical Kit w/370W Motor For CNC Engraving Milling Machine USA STOCK

♞【Upgrade Version CNC3018 Pro Max with offline controller】Mini CNC machine small size, light weight, USB interface, GRBL control systems, great cnc router machine for beginers.
3018 PRO MAX machine is very easy to install,stable structure,our parcel also include english user manual.Supporting files:G-code (.nc/.txt/.tape/.gcode).
♞【Upgraded GRBL1.1 Control Board】Added the outer casing,emergency stop button port,tool setting (probe) port,X/Y/Z axis limit port and add the power button switch,and come with the fan port to force heat dissipation,with enhanced spindle drive,can support maximum 20000rpm spindle,and also can support 0.5W-20W module.【Working area】30x18x4.5cm.
Type:USB port Desktop cnc router【System requirements】Windows XP / Win 7 / Win 8 / Win 10 / Linux.
♞【Spindle&Stepper Motor】775 spindle motor (12-36V) 24V:10000r / min.
Collet: ER11 3.175mm (Can be equipped with 0-7mm).
♞【Main application】Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material.soft metal like copper and aluminum and other materials, but can not carve hard metal, jade or other very hard texture of the items. if you have the module....

Check Stock

Twotrees CNC Controller Kit with Nema 23 Stepper Motor,TB6600 Stepper Motor Driver,GRBL CNC Shield Board，Switch Endstop-6.35mm

Newest CNC Shield Expansion Board V3.0 ---CNC shield board is updated version 3.0, which is suitable for CH340G Shield 3.0 version compatible with for....
More Compatibility Possibilities---It's a DIY kit with tons of possibilities. This complete CNC kit is GRBL compatible and has all the essential....
Premium Quality --- Each part of this Logrunner 3d printer conk kit was made of premium material. These components can be used in a wide range of....
Professional 3D Printer CNC Kit --- This is a professional 3d printer DIY kit with multiple types of modules or components you need. It is a great....
Package Included:---1* CNC V3 ，1* Control Board ， 4* TB6600 ， 4* Limited Switches ，4* 23HS5628 Motor with 30cm wire (8mm/6.35mm Shaft....

Check Stock

SainSmart Genmtisu CNC Router Machine Controller Board with ABS Case for CNC 1810-PRO/3018/3018-PRO

This controller board is designed for Genmitsu CNC Router 1810-PRO, 3018, and 3018-PRO. It can perfectly compatible with SainSmart Blue Laser Module..
Software: GRBL controller, UniversalGcodeSender..
Support XYZ three-axis control, spindle and laser module. Support 3 pin and 2 pin lasers (the 2 pin lasers: please connect the white interface " + s-")..
Support stepper motor: 12V, the maximum current within 2A, recommended within 1.5A and additional heat. (Any stepper motor 42, 57)..

Check Stock

Module A9G Board, A9G Development Board GSM/GPRS + GPS/BDS Module Wireless Data Transmission + Positioning Board

★[A9G Development Board] – The A9G development board is a versatile development board based on A9G GPRS / GSM + GPS / BDS module that can be used to validate the basic communication functions and peripheral functions of the A9G module..
★[Multifunction] – A9G development board with the basic phone / SMS, GPRS networking communications, GPS / BDS dual-mode positioning capabilities..
★[Specification] – A9G development board contains a lithium battery charging management, microphone, speaker interface, USB communication interface, multiple user keys / led, TF card slot, accelerometer, I2C2 interface, ADC interface..
★[External Interface] – A9G development board camera expansion board, an external 30W / 200W camera.A9G development board coin machine expansion board, can be external traditional coin machine..
★[After-Sale Service] — Good day. every effort to provide customers with satisfactory service.If you have ANY questions, please email us and BELIEVE us, we will reply you soon..

Check Stock