Top Clutch Tool Reviews

SR Performance Clutch Alignment Tool; 10 Spline

OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
Rugged construction will easily support the weight of heavy clutch discs.
To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
1-3/4 inch O.D. shaft, 1 inch pilot, 10 splines.

Check Stock

NexADD Fan Clutch Wrench Set 32mm & 36mm Water Pump Holder Tool Fit for BMW Ford GM Chevrolet,Fan Clutch Nut Wrench Set,Fan Clutch Removal Tool,Water Pump Pulley Holder,Clutch Fan Removal Tool Kit

REMOVE & REINSTALL AUTOMOTIVE FAN CLUTCHES ★- The NexADD 32mm & 36mm Fan Clutch Wrench Kit with Fan Pulley Holding Tool removes lock nuts on temperature-dependent thermo-viscous fans. The holder bar keeps the water pump pulley in place while loosening the radiator fan. It is a direct replacement and completely fit, wich could help you save much money..
FITS YOUR VEHICLE★-The NexADD Fan Clutch Wrench Set is compatible with BMW vehicles, including, but not limited to,the following applications: fan clutch wrench tool is kit compatible with BMW M4 M10 M20 M30 M40 M44 M50 M52 M52TU M54 M56 M60 M70 M73 S14 S38 S54 S50B30 S50B32 and compatible with Ford.Also compatible with some Ford, GM, and Chevy models..
BUILT TO LAST★- The 15" fan clutch wrench and holder are specially lengthened to provide extra leverage with sure grip when working on hard-to-get-to fan clutch nuts on metric thermo-viscous fans, letting you service your timing or water pump quickly and easily. The rubber handle covered in the middle helps prevent hand fatigue during prolonged us..
EASY TO USE ★- Attach the pulley holder bar with your bolts inserted through the holes, lock into place on water pump face, place wrench on fan clutch nut, and loosen the fan clutch nut by turning clock....

Check Stock

Dorman 14505 Clutch Alignment Tool Compatible with Select Models

OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
Rugged construction will easily support the weight of heavy clutch discs.
To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
2 inch O.D. shaft, 1-1/4 inch pilot, 10 splines, splines are 3.6 inches long.

Check Stock

QISF 2Pcs Magneto Flywheel Puller 24mm & 27mm and 20mm & 24mm Clutch Lock Nut Spanner Tool for Motorcycle ATV Dirt Bike Scooter Repair Tool

【Function】-- Clutch plate hub nut spanner tool designed to loosen and tighten the lock nut for the removal and installation of a motorcycle clutch.Another Used for removal of the flywheel or rotor if applicable..
【Fits】 Flywheel Puller for GY6 50CC 125CC 150CC Yamaha Honda Suzuki KTM ATV scooter dirt bike.
Clutch lock tool for 50cc-125cc Honda Motorcycle ATV Dirt Bike Go Kart Pit Bike 4 Wheeler.
【Flywheel puller Size & Material】-- Stator magneto flywheel puller with 2 sizes:24mm&27mm.
【Clutch lock Size】-- Clutch lock tool Inner Diameter(upper): 20mm.
【Package includes】-- 1×Magneto Flywheel Puller, 1×Clutch lock tool.

Check Stock

RZR Clutch Cover Removal Tool kemimoto RZR Removal Tool kit with Reversible Socket Compatible with Polaris RZR XP 1000/ XP Turbo RS1 Ranger XP 1000

【Fitment】-Clutch removal tool only Compatible with 2016 2017 2018 2019 2020 Polaris RZR/RZR-4 XP Turbo & RS1, 2018 Polaris Ranger XP 1000 & 2019....
【 Flexible shaft】-RZR removal tool with flexible shaft and no-slip grip,which can be used within 90 degree bending range. The clutch cover removal....
【Reversible】-kemimoto RZR clutch cover removal tool with a reversible socket that fits 8 mm clutch cover screw heads and 1/4" hose clamp. The....
【Comfortable to use】-This clutch removal tool handle is designed according to ergonomic principles. Ensure the comfort of your hands during the....
【Durable】-Removal tool of RZR is made of aluminum alloy, which is lighter and will not rust compared to other tools made of steel, and can be used....

Check Stock

2-in-1 Lock Nut Wrench Clutch Lock Nut Tool 20mm/24mm clutch lock nut spanner socket for Crf 600rr 450r 250l

STURDY SOLID MATERIAL -- The clutch lock nut spanner is made of solid steel material, sturdy construction, durable in using.
DESIGNED FOR LOCK SPANNER KIT -- A special and perfect replace grom clutch removal tool for : Replace special tool: # 07716-0020100,....
IMPORTANT DATA FOR YOU TO CHECK -- Large End Inner Diameter: 24mm / 0.94 inch.
Large End Outer Diameter: 30mm / 1.18 inch.
COMES WITH 4 PIN LOCK NUT SPANNER -- 4-pin socket clutch nut tool, each end has 4 pegs.
One side is 20mm inner diameter and another side is 24mm inner....
FITMENT -- This clutch nut tool can be used for 14mm clutch lock nut on: crf50, xr200 1980-1984, xr200r 1984-1994, xr250l 1991-1994, xr250r 1986-1994,....

Check Stock

ClutchXperts SPC Clutch Alignment Tool KIT Compatible With 2006-2015 Mazda MX-5 Miata 2.0L 6-Speed

OTC's 10-Spline Truck Clutch Alignment Tool is designed for use when installing heavy-duty single, two-plate, push/pull, manual, and self-adjusting clutches.
Tool is constructed of lightweight fiberglass-reinforced nylon that won't hang up in clutch disc splines.
Rugged construction will easily support the weight of heavy clutch discs.
To use, loosely install clutch disc and pressure plate on flywheel then insert alignment tool through the clutch into the bearing, center disc, then tighten pressure plate to spec.
2 inch O.D. shaft, 1-1/4 inch pilot, 10 splines, splines are 7.3 inches long.

Check Stock

ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch Puller for Car Auto Air Conditioning on GM, Ford, Chrysler

REPLACe A/C CLUTCH ASSEMBLY: Use the ABN Air Compressor Clutch Rebuild Removal Tool Kit – AC Clutch Puller for Car Auto Air Conditioning to remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors.
GM R4 and A6, HR-6, DA-6 and V A/C compressors.
sander compressors SD 505, 507, 575, 708, and 709.
Wide application of vehicles including GM, Ford, Chrysler, imports, and other makes and models.
Check vehicle owner’s manual for a list of compatible compressors.
EASY TO USE: Keep all threads clean and well-oiled.
Outer part of tool has smooth side and threaded side (threads used to attach to inner clutch shaft when removing).
Start with one bearing between tool and clutch, and thread down fully onto compressor's inner shaft threads (This is the fixed part - inner bolt does not move when threading down outer piece).
Remove tool and stack other bearing on to take up the distance the clutch pushed into pulley.
BUILT TO LAST: Constructed from stainless steel with a black coated finish for ultimate strength and longevity.
Resists rust and corrosion with proper care and lubrication.
2 and 3 hold puller plate allows mechanical force to do all of the pulling on most clutches.
EASY STORAGE: Heavy-duty 10.5” x 8.25” x 2.25” inch (2....

Check Stock

BILITOOLS Fan Clutch Removal Tool Kit, Fan Clutch Wrench Set 22 36 40 47 51 MM with Pulley Holder

Fan clutch service tool set includes 5x Fan clutch wrenches - 22mm, 36mm, 40mm, 47mm, 51mm.
Special fan clutch wrench tool kit is designed to remove and install fan clutches when repairing or replacing the water pump, timing chain or the fan clutch..
The pulley holder with 4 pairs of replacement pins is designed to trap and hold bolt on pulleys by the mouting bolts. It is suitable for most vehicles and newer Chrysler engines with press on pulleys requiring sprcial pins to hold housing..
This fan clutch tool Kit is made from forged steel for superior strength, black finish further improves corrosion resistance for lasting durability..
The fan clutch wrenches are compatible with Ford Trucks (2.8L, 2.9L, 3.0L, 4.0L, 1.9L engines), Dodge Trucks (3.9L, 5.2L, 5.9L, 8.0L, V10 engines), GM Trucks (4.3L, 5.0L, 5.7L engines), ect..

Check Stock

YHB 32mm & 36mm Fan Clutch Nut Wrench and Water Pump Holder Tool Kit Removal for BMW Fan Clutch Tool Removal kit (3pcs) - Fan Clutch Removal Tool 36mm and 32mm Fan Clutch Tool Kit

【Item name】 Fan Clutch Nut Wrench, Clutch Removal Tool Kit, Fan Clutch Wrench Set, Water Pump Holder Removal Tool Kit, designed to easily remove the lock nuts on a temperature dependent thermo-viscous fan..
【Compatible with】Fan Clutch Nut Wrench Compatible with BMW E34 E46 E90 E39 E36.
【Applications】32mm Clutch Removal Tool Kit Made to be compatible with BMW engine models M4 M10 M20 M30 M40 M44 M50 M52 M52TU M54 M56 M60 M70 M73 S14 S38 S54 S50B30 S50B32.
【Features】FEXON Fan Clutch Wrench Set makes it easy to hold water pump pulleys in place while you loosen and service your radiator fan. The tools have been heat treated to improve product performance..
【Easy to Use】Quickly removes and installs fan clutch when repairing the water pump or fan clutch..

Check Stock

Van SanShao years Replace Echo Clutch Removal Tool CS-400 CS-500 CS-510 for Echo Chainsaws 89750516133

Clutch Removal Tool for Echo Chainsaws / Echo Part # 89750516133.
Replaces: Echo Part #s 89750516132, 89750516131, 89750516130, 89750502830, 89750503930, 89771002830.
Fits Echo Chainsaw Models: CS-4600 S/N, CS-5000 Type 1E, CS-510 S/N, CS-5500 S/N, CS-520 S/N, CS-4000, CS-4500, CS-4600 S/N, CS-5500 S/N.
The metal tool is used to remove the clutch from the crankshaft. This item fits over the clutch and a wrench or ratchet is used to put leverage on the....
Package Qty: 1 Clutch Removal Tool for Chainsaws.

Check Stock

UNIGT Belt Changing Tool with Clutch Cover Removal Tool Kit Replacement for Polaris XP/RZR XP4 1000/RZR S 900

Belt changing tool help RZR owner to change a belt, the clutch tool can help you easy to remove the clutch cover.
Belt changing tool made by Solid Aluminum Alloy, the clutch tool is dismountable and flexible.
A must tool kit for your Polaris RZR: The RZR belt changing tool makes changing your belt easier,and speed up change belts,save the time of Polaris RZR owner.
Custom design: This rzr belt removal tool is custom made for Polaris XP/RZR XP4 1000/RZR S 900 etc almost all Polaris rzr belts.
Easy to use: the belt changing tool is with an ergonomic handle for a comfortable grip, it’s very easy to changing the belt. It can be rotated 360 degrees..

Check Stock

UNIGT Clutch Cover Removal Tool Compatible with Polaris RZR XP Turbo RS1 Ranger XP 1000 Reversible Belt Changing Tool with Socket Kit Belt Tool

Belt changing tool help RZR owner to change a belt, the clutch tool can help you easy to remove the clutch cover.
Belt changing tool made by Solid Aluminum Alloy, the clutch tool is dismountable and flexible.
A must tool kit for your Polaris RZR: The RZR belt changing tool makes changing your belt easier,and speed up change belts,save the time of Polaris....
Custom design: This rzr belt removal tool is custom made for Polaris XP/RZR XP4 1000/RZR S 900 etc almost all Polaris rzr belts.
Easy to use: the belt changing tool is with an ergonomic handle for a comfortable grip, it’s very easy to changing the belt. It can be rotated 360....

Check Stock